LIVINOX LCH-ROSEDC-90BL User manual

1
LCH-ROSEDC-90BL
User Manual

2
From the Manufacturer
Please read this user manual carefully before attempting to operate the appliance and keep it in a safe place for
future reference.
This appliance and its packaging are produced by processes that minimize waste and respect the environment.
Please help us to continue this effort to protect the environment by using the appliance efficiently and dispose of
the packaging in a responsible manner.
FOR THE USER
1. Safety Instruction
Warning
PLEASE READ THIS SECTION THOROUGHLY BEFORE ATTEMPTING TO OPERATE THE
APPLIANCE
1.To ensure adequate ventilation in the room when the range hood is in use at the same time as gas/fuel burning
cooking appliances (this is not applicable to appliances that only discharge the air back into the room).
2.There is a fire risk if cleaning is not carried out in accordance with the instructions.
3.To avoid using food products that produce flame under the range hood.
4.Do not “flambé“ food (is a cooking procedure in which alcohol is added to a hot pan to create a burst of flames)
under the range hood.
5.Sufficient air is needed for proper exhausting of gases through flue (chimney) of fuel burning appliances.
6.This appliance is not intended for use by persons (including children) with reduced physical, sensory, mental
capabilities, lack of experience and knowledge.
7.To reduce risk of fire and to properly exhaust air and to ensure to duct air outside. Do not vent exhaust air into
spaces within walls, ceilings, into attics and crawl spaces.
Installation
1. This appliance must be installed or repaired by a qualified technician only.
2. Do not modify any part of this appliance by yourself.
3. To ensure the location in which this appliance is installed has good and permanent ventilation.
4. In ducted mode, there must be one or more permanent air inlet. The air collected must not be discharged into
a duct used to blow off smoke from other appliances fed with electricity.
5. The distance between the bench to the lower part of the hood must not be less than 300-350mm.
6. Use an electrical connector with earth that is correct for your location.
7. To check the voltage in your area correspond to the appliance as indicated on the rating label.
8. Do not connect the hood to a duct that carries combustion fumes (e.g. fireplace).
Intended For Household Use
1.This product is designed for household use only and should never be used for commercial applications.
2.After use, always ensure that all controls are in the "OFF" position.
3.When frying with a gas flame, take particular care not to allow the oil or grease in the pan to catch fire.

3
Cleaning, Maintenance & Service
It is very important to clean and maintain the grease filters regularly (at least once monthly) to improve its efficiency
in eliminating heat and contaminated air in the kitchen. Heavy oil deposits is a fire hazard. Hood surface should be
cleaned with soft cloth and non-corrosive detergent.
Important: Never attempt to repair this appliance by yourself. Always refer to qualified Service Technicians.
For safety precaution, always purchase the original replacement parts.
Always switch off the power and unplug the connection before conducting maintenance or cleaning.
Electrical Cord
1.To ensure the electrical cord is not exposed to heat, chemical or sharp objects.
2.If the electrical cord is damaged, it must be replaced by the manufacturer or its service agent or qualified
electrician.
2. Dimension Diagrams
3. Instructions for use

4
Press Turbo,The indicator blinks three times,its indicator light is on and the fan is at booster/highest
speed (LED Screen shows “F4”). After running for 3 minutes, it will automatically switch
to high speed state. Press again, the motor will stop working, the indicator light will be off,
and the range hood will enter non-working state.
Press +,Press + once,The indicator blinks three times, the fan is working at low speed (LED screen shows”F1”).
Press C second ,The indicator blinks three times, the fan runs at mid speed (LED screen shows “F2”).
Press C third,The indicator blinks three times ,the fan runs at high speed (LED Screen shows “F3”).
Press C fourth,The indicator blinks three times ,The display shows the time,enter non-working state.
Press -,Press - once,The indicator blinks three times, the fan is working at high speed (LED screen shows”F3”).
Press C second ,The indicator blinks three times, the fan runs at mid speed (LED screen shows “F2”).
Press C third,The indicator blinks three times ,the fan runs at low speed (LED Screen shows “F1”).
Press C fourth,The indicator blinks three times ,The display shows the time,enter non-working state.
Press Auto Clean,In non-working state, press Auto Clean for 3 seconds, oil removing function will operate for 10
minutes(The fan will automatically operate at high speed for 1 minute after the 10 minutes cleaning
function. ). press Auto Clean for 3 seconds again,The indicator blinks three times, turn off oil removing
function.
Press ,In non-working state, Press 3 seconds to set clock, the hour position on LED screen twinkles then you
can use + and - to set hour. Press Settings once again, the minute position on LED screen twinkles then
you can use + and - to set minute.
Press ,turn on power. Press it again, turn off power.
Press ,In non-working/ working state,Press once, The indicator blinks three times,turn on the light. Press
again,The indicator blinks three times, turn off the light.
Cleaning & Maintenance
ALWAYS SWITCH OFF AND UNPLUG FIRST!
SURFACES:
Wash with warm soapy water and a soft sponge. Never use abrasive detergent, scouring pads, steel wool or
solvents on any part of this appliance as this will cause irreparable damage.
ALUMINIUM NET:
Wash in the dishwashers or soak the panels in a degreasing agent for an hour, then rinse off and dry before re-
installing.
For this appliance to function effectively, regular maintenance is a must.
Clogged filters restrict airflow and may cause the motor to overheat.

5
4. Installation
1. Use suitable bolts to mount the appliance on a secure surface.
2. The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest
part of the range hood. When the range hood is located above a gas appliance, this distance should
between 300-350mm. If the instructions for installation for the gas hob specify a greater distance, this has
to be taken into consideration.
3. To obtain best performance, it is advisable to install in an air ventilated area.
4. Do not install the outlet of the exhaust duct in the wind direction, which can prevent the exhaust air from
flowing backward.
5. Fasten the components on exhaust outlet with screws. To perform for smooth airflow, the exhaust duct
should bend in L-shape till exhaust outlet
1) Complete components include as follow :
NOTE: Fixing Screws bag should contain :
Screw Size
ST4.8 x 3PCS
M4-10 x 4PCS
M4-8 x 15PCS
ST2.9-12 x 2PCS
ST3.9-25 x 4PCS (including 4PCS plastic expansion
bolt)
ST5-40 x 3PCS (including 3PCS plastic expansion
bolt)
1M grey sponge tape

6
2) Use a phillips screwdriver to loosen the two pieces of screws on the left and right side and remove chimneys
as per below fig.：
3) Install duct cover：
Please remove the sponge tape and adhere it under the bottom of the duct cover. Remove the four screws
(M4*16mm) from motor outlet, Fix the duct cover onto fan assembly as per below fig.
4) Please connect the wires between fan assembly and chamber assembly as per below fig

7
5) Fix the Fan Assembly & Chamber Assembly by using the 10 pcs M4x8mm screws to tighten it as per below
fig.
6) LED light plug must pull out from the hole to enable the connection to LED lamp.

8
7) Install the Exhaust Duct: Fix the Exhaust Duct and duct cover tightly with 2 pcs ST2.9*12mm screws. Then
fix 2pcs M4*10MM screws to each side of the body.
Remarks: Do not screw too tight, keep about 5mm gap between the body and M4*10mm screw head as per
below fig
8) Install The Hook ：Measure a standard hanging height and pre-drill 3 holes by horizontal position on the wall,
and drive the plastic expansion bolt into the holes. Use 3pcs ST4.8 screws to fasten the hook on wall firmly.

9
9) Install the fan assembly into the chamber assembly and align the second holes with 2pcs M4 screws.
Connect LED light plug into fan assembly
10)1st chimney and ducting cover bracket connection : Use a philips screw driver to fix the ducting cover bracket
into the extra chimney with 2 PCS Screws M4*8 mm as below fig.：

10
11) Install the cooker hood：Hang the complete set onto the hook firmly.
12)2nd Chimney installation：Measure a suitable height for 2nd Chimney and pre-drill with 2 screws holes by
horizontal position on wall. Insert the plastic expansion bolt into the holes and tighten the ducting bracket by 2
pcs ST3.8*25mm screws. Pull up the 2nd chimney to fix on the bracket.

11
FOR THE INSTALLER
5. Safety Information
1. Electrical connection must be in accordance with the local standards and laws.
2. To ensure that the electrical supply in compliance with the appliance setting, otherwise, do not
connect.
3. To ensure the power supply cord is free from any heat source or sharp objects.
4. The electrical connection of this appliance must be soundly earthed. In the event of electrical short
circuit, grounding reduces the risk of electrical shock. If unsure, contact a qualified electrician.
5. Replacement of lamp must not exceed 20W.
6. LED lamp must not exceed 1.5W/7W.
Wire Color Codes:
Green & Yellow = EARTH
Blue = NEUTRAL
Brown = LIVE
6. Trouble shooting

12
Problems
Possible Cause
Action
Not function
No power supply
Check that the main switch is turned
on
Check that the plug is connected
Poor airflow
Aluminum grease filter clogged
Clean the filters and replace when
dry
Charcoal grease filters clogged
Replace charcoal filters with new
sets
Motor running but no
airflow
Butterfly valve jammed
Contact technician
Motor cuts after a few
minutes
High temperature safety device
activated
The kitchen is not sufficiently
ventilated
The hood is installed too near
the cooking stove
The hood must be at least 300mm
from stove
Strong cooking smell
Airflow weak/ventilation clog
Clean the Aluminum filter and
replace when dry.
Check duct cover valve, contact
technician if jammed.
Oil dripping
Oil cup missing or not installed
Remove aluminum filter and replace
oil cup
aluminum grease filter saturated
Wash the aluminum grease filters
Whirring sound
Abnormal object clog on fan
blade
Contact technician

13