livn DUBLIN User manual

EN WALL MOUNTED FIREPLACE DUBLIN
NL HANGHAARD DUBLIN
FR CHEMINEE MURALE DUBLIN
DE WANDKAMIN DUBLIN
EN Instruction manual NL Handleiding FR Manuel d'instructions DE Bedienungsanleitung

2
EN INSTRUCTION MANUAL
Important:
Please read the instruction manual carefully before installing or using the electric fireplace and please
keep it for future reference. This manual is part of the device and should be stored with it. If sold to a
third party, this manual should be supplied with the product. Liability will not be accepted, and the
warrant shall not apply in case of improper use or failure to follow the safety instructions. For
assistance or additional information, contact a qualified technician, the help desk, or the point of sale.
SECTION 1: WARNINGS & ELECTRIC SPECIFICATIONS
1.1 Important Safety Instructions
This symbol alerts you to potential hazards
that can kill or hurt you and/or others
DO NOT:
•Install or operate a damaged heater
•Modify the heater
•Operate the heater without fully assembling all components
WARNING!
Improper installation, adjustment, alteration, service, or maintenance can cause
injury or property damage. Refer to the owner’s information manual provided with this
heater. For assistance or additional information consult a qualified installer, a service
agency or your dealer.
WARNING!
When using electrical heaters, basic precautions should always be followed to reduce
the risk of fire, electric shock, and injury to persons, including the following:
•Do not use this heater in the immediate surroundings of a bath, a shower, or a swimming
pool.
•Do not switch on the electric fire until it has been properly installed, as described in the
manual (however, it is important to test the fire before you built it in).
•Never leave the appliance burning while you are away.
•Never leave the appliance connected to the power supply while you are away.
•The appliance is intended for domestic use and must not be used for industrial purposes.
•Do not use the appliance with wet hands.
•For indoor use only. This appliance is not suitable for use outside the house and only
suitable for well insulated spaces or occasional use.
•Do not use the appliance on or near hot surfaces.
•The appliance may only be cleaned when the electric fire has been disconnected from the
mains/socket and when the electric fire has cooled down completely.
•Never clean the electric fireplace with aggressive cleaning agents.
•Never use accessories not recommended by Livn. It may endanger the user or damage the
electric fireplace.
•Do not use this fire as a free-standing appliance. It must always be fixed to the wall.

3
•This appliance must not be supplied through an external switching device, such as a timer,
or connected to the circuit that is regularly switched on and off by utility in order to avoid
a hazard due to the inadvertent resetting of the thermal cut out.
•To reduce the risk of fire, keep textiles, curtains, or any other flammable material a
minimum distance of 1 meter from the air outlet.
•Keep the power cord away from hot surfaces and hot conditions. Do not route the power
lead in front of the appliance.
•This heater must be earthed. If in any doubt consult a suitable competent person.
•This heater must not be located immediately below a socket-outlet.
•This appliance can be used by children aged from 8 years and above, and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved.
•Children shall not play with the appliance.
•Cleaning and user maintenance shall not be made by children aged from 8 years and above
without supervision.
•Children of less than 3 years should be kept away unless continuously supervised.
•Children aged from 3 years and less than 8 years shall only switch on/off the appliance
provided that it has been placed or installed in its intended normal operating position and
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children aged from 3 years and less than 8 years
shall not plug in, regulate, and clean the appliance or perform user maintenance.
•Some parts of this product can become very hot and cause burns. Particular attention has
to be given where children and vulnerable people are present.
•DO NOT use this appliance in small rooms that are occupied by persons not capable of
leaving the room on their own, unless constant supervision is provided.
•Do not cover: In order to avoid overheating, do not cover the heater.
•The meaning of figure in marking is “WARNING: DO NOT COVER”.
•Do not use the electric fire with a damaged plug or cord, after a malfunction, after a fall or
when the fire has been damaged in any way.
•Make sure that the power cord never passes sharp edges, comes into contact with hot
surfaces or gets tangled.
•Do not let the power cord run under carpets, rugs, etc.
•Warning: in order to avoid overheating, do not allow the appliance to be covered or let
the air inlet/outlet become obstructed.
•Do not disconnect the appliance from the power while it is in operation. Use the functions
of the remote control to switch off the fire and make sure that the main switch is in the
OFF (“o”) position before removing the plug from the socket.
•If the power cord is damaged, it must be repaired by the manufacturer, its authorized
service centre or professional person.
•Keep the power plug accessible after installation.
•Never immerse the product in water or other liquids.
•Do not use this fire in rooms that have explosive gas in them (for example petrol), or if you
are using solvents, glue, aerosol spray or in flammable paints, as these may catch fire.
•DO NOT use if there are visible signs of damage to the appliance.
•DO NOT use this appliance if it has been dropped.

4
1.2 Specifications
Model No.: Dublin
Supply Voltage: AC 220-240V 50Hz
Maximum power consumption: 2KW
Power for flame effect: 6,4 (LED 2,4W + Motor for flame 4W)
Power for background lighting: DC12V, Max 1,92W, 0,16A
Heat Output:
Nominal heat output (Pnom): 2KW
Minimum heat output(indicative) (Pmin): 1KW
Maximum continuous heat output (Pmax): 2KW
Auxiliary Electricity Consumption:
At nominal heat output (elmax): 12.5W
At minimum heat output (elmin): 12.0W
In standby mode (elSB): 0.48W
Type of heat output / room temperature control
Single stage heat output and no room temperature control
No
Two or more manual stages, no room temperature control
No
With mechanic thermostat room temperature control
No
With electronic room temperature control
Yes
Electronic room temperature control plus day timer
Yes
Electronic room temperature control plus week timer
Yes
Other Control Options
Room temperature control, with presence detection
No
Room temperature control, with open window detection
Yes
With distance control option
No
With adaptive start control
Yes
With working time limitation
No
With black bulb sensor
No

5
SECTION 2: INSTALLATION
Tools required
Magnetic Screw Driver
Rotary Hammer
Content of the package
Mounting materials, remote control, batteries, user manual, electric fireplace.
2.1 Unpacking the Fireplace
WARNING! Do NOT use this appliance if any part has been under water. Immediately call a
qualified service technician to inspect and to replace any part of the electrical system if
necessary. Keep plastic wrapping away from children.
•Open the packaging carefully and remove the foam; make sure that the appliance is intact, has
no signs of damage caused by transport, and no part of it has been exposed to water. If in doubt,
do not use the appliance and contact an authorized service centre.
•Remove and discard the plastic bag.
•Be responsible when handling the packing materials.
•Keep the original packaging because this may be needed if you have a complaint about the product
or for future transport and/or storage.
•Make sure that all parts are removed from the packing.
•Keep little children away before and during installation. Be aware that the little children do not be
in contact with the parts.
•The electric fireplace can be installed almost anywhere in your home. Please, read and follow the
instructions carefully by choosing a location. For the best result, install the electric fireplace not in
direct sunlight.
•The appliance should be connected to an earthed electrical outlet that can be easily accessed to
disconnect the device.

6
2.2 Dimensions

7
2.3 Mounting instructions
STEP 1. Find a safe location. Minimum clearance on the left and right side must be at least 100mm;
minimum clearance from ceiling must be at least 200 mm; minimum clearance from the floor must
be at least 400 mm; minimum clearance from the front must be at least 3 feet 3⅜ inches (100 cm).
Choose a location near an outlet so an extension cord is not required. DO NOT position the unit
directly below a power outlet.
STEP 2. Choose a solid and plain wall and then put the bracket on the position where you want to
install the fireplace. Mark the 4 holes by a pen from the holes on the bracket. Take away the bracket
and then drill 4pcs Φ8 holes on the wall. Put the plastic wall plug into the hole. If the wall is solid
wood, it is no needed to drill the holes on the wood and no needed of the plastic wall plug. Then
use 4pcs ST5*40 to fix the bracket to the wall.
STEP 3. With the firebox at an angle, fit the slots in the back of firebox over the hooks on the wall
mount bracket, and carefully press the top of the firebox against the wall mount bracket. The slots
at the top edge of the firebox should slide over the wall mount bracket tabs. Hold the firebox in
place and thread the thumb screws through the holes in the firebox and into the wall mount bracket
tabs. Tighten both thumb screws and make sure the firebox is secure to the wall.

8
STEP 4. Carefully arrange the decorative stones (WS/CS) along the inset window ledge at the front
of the firebox. Use care when relocating the fireplace to prevent the stones from falling out.
STEP 5. 1. Carefully set both hooks of the front glass panel into the slots at the top front edge of the
firebox. 2. Press the two posts of the glass panel into the locking slots near the lower corners of the
front firebox panel. NOTE: Make sure the posts click into the slots. This will keep the decorative
glass in place. 3. Thread the M4x8 machine screws through the glass panel hooks and into the
threaded holes in the firebox. Partially tighten by hand. Check the alignment of the glass panel and
securely tighten the screws with a Phillips screwdriver.

9
SECTION 3: OPERATING INSTRUCTIONS
WARNING: Do not operate the appliance if it is damaged or has malfunctioned. If you suspect the
appliance is damaged or has malfunctioned, call a qualified service engineer to inspect the appliance,
and replace any part of the electrical system, if necessary, before re-use.
MAKE SURE that the plug fits tightly into the outlet. Faulty wall outlet connections or loose plugs can
cause the outlet to overheat.
This appliance can be operated by both remote control and manual buttons. Once the unit has been
properly connected to an earthed electrical outlet, turn on the main power switch that is located on
the control panel located on the bottom right-hand side of the firebox. A beep should be heard when
the power is first applied.
NOTE! To use both remote and manual functions the manual on/off switch must be in ‘ON’ position.
In order to protect the product not becoming too hot, there is 10 seconds delay when turning on the
heater; also, there is 10 seconds delay when turning off the heater fan.
3.1 Operating by Manual Button
NOTE! The manual button on the fire box unit will not provide you with all function control, and its
propose is to control some basic function when you lose the remote handset. Please use the remote
handset to carry out all functions.
MAIN POWER SWITCH
Switch ON (|) before operating either the remote or manual controls.
LIGHTS ON/OFF BUTTON
Press “LIGHTS ON/OFF” to turn on or turn off both the flame and fuel bed at the same time.
FLAME BUTTON
Press “FLAME” button to select the colour of flame (3 colours) or return to the OFF position.
MOOD LIGHT BUTTON
Press “MOOD LIGHT” button to select the colour of mood light (13 colours), colour-cycle mode or
return to the OFF position.
NOTE: The controls on appliance will lose the memory for all function settings when the switch is set
to the Off Position. When the remote runs out of power or when you change the batteries, only the
flame function will lose memory and will not affect the timer settings, however, the clock may need
adjusting.

10
3.2 Operating by Remote Handset
•Make sure the batteries are installed properly in the remote control.
•The effective range of the remote control is up to 4 meters or 13 feet.
•Aim the remote control at the remote receiver which is behind the middle of the flame screen.
NOTE: This is a thermostatic remote control. The remote should be in the same room as fireplace and
placed on a flat surface. It must be placed away from the heater so the hot air will not blow on it and
affect thermostatic reading.
The communication frequency between the fire and remote has already been set up. If you cannot use
the remote with the fire, please follow instructions Step 3.2.34 to initiate this connection in point.
Stand-by for Remote Handset
3.2.1 The screen shown to the right is when the remote handset is in standby condition.
Turn on/off
3.2.2 Press to turn on the flame effect, turn off flame effect and heater when in normal
mode.
3.2.3 Press to turn on/off the flame effect under daily and weekly timer mode.
Flame Effect
3.2.4 Press to enter the flame effect adjustment screen.
3.2.5 Press the ‘←’ and ‘→’ button to select the 3 kinds of flame effect.
3.2.6 Press the ‘+’ and ‘-’ button to select the 5 brightness of flame effect and OFF settings.
Mood Light
3.2.7 Press to enter the mood light adjustment screen.
3.2.8 Press the ‘←’ and ‘→’ button to cycle through the 13 mood light colour options.
3.2.9 Press the ‘+’ and ‘-’ button to increase the mood light brightness.

11
Normal Mode
3.2.10 Normal control mode is factory set. If it is not, then press button until the
logo shows up at the upper right corner of the screen.
3.2.11 Press the ‘+’ and ‘-’ button to adjust the setting temperature from 17°C to 25°C by 2
intervals.
3.2.12 Press button to turn on/off heat, ON or OFF will show at the lower part of
the screen.
NOTE: It is normal for the fan heater to stop running for periods of time. This happens because the
room temperature is at or above the temperature set on the remote control. The heater indicator
will be turned off after 10s if you have the flame ON. The heater indicator will stay ON if you only
use the heating function.
Count Down Timer
NOTE: This setting is only for normal mode. It allows the appliance to go into
standby after a set period.
3.2.13 Press to cycle through the settings from OFF and 0.5 hours to 9 hours. The timer
logo and time will show on the screen. The heater must be inthe ON position.
Set up Day, Time and Comfortable temperature
3.2.14 Press to turn on the remote handset. Hold the button for 3 seconds to enter
the setting screen.
3.2.15 Press the ‘←’ and ‘→’ button to choose Day, Time or your comfortable temperature.
The character selected will be highlighted.
3.2.16 Pressing the ‘+’ and ‘-’ button will adjust the number.
•Time: 24-hour system
•Select your comfortable temperature from 15-25°C.
•Temperature unit: °C or °F
Daily Timer Heating
3.2.17 The following are preset heating periods, which can be altered if desired.
06:00 until 08:30
17:00 until 22:00
3.2.18 Press until shows at the upper right corner of the screen, then enter the daily
timer heating mode
3.2.19 Hold the arrow symbol button for 6 seconds to enter the daily timer setting. Max
3 timed heating periods per day.
•Press ‘←’ or ‘→’ to choose hour or minute, press ‘+’ or ‘-’ to set the time.
•Minute will increase/decrease by 15 minutes per press.
•Hold for 3 seconds or wait for 10 seconds to save and exit the heating
time period setting.

12
Adjust the set temperature
3.2.20 Press the ‘+’ or ‘-’ button to increase or decrease the set temperature based on your
comfortable temperature setting.
ECO means 2°C lower than your comfortable temperature setting, ECO- means
4°C lower, COMF+ means 2°C higher, COMF++ means 4°C higher.
3.2.21 To check your daily timer settings, press .
3.2.22 If heating needs to be turned off, it will be necessary to go back to the Normal Mode to
turn off.
Week Timer Heating
3.2.23 The following are preset heating periods, which can be altered if desired. From Monday
to Friday.
06:00 until 08:30
17:00 until 22:00
From Saturday to Sunday
06:30 until 09:30
11:00 until 13:00
17:00 until 22:00
3.2.24 Press until shows at the upper right corner of the screen, then enter the week
timer heating mode.
3.2.25 Hold button for 6 seconds to enter the week timer setting.
•Press ‘←’ or ‘→’ to move the cursor (a flashing underline), press the
button in the corresponding week position to select (the character is
highlighted) or cancel (the character is displayed normally) the current
setting. Several days can be selected together.
•Press the ‘→’ button to move the cursor to the time period setting area.
•Press ‘←’ or ‘→’ to choose hour or minute, press ‘+’ or ‘-’ to set the number.
•Max 3 heating periods for a day.
•Minute will increase/decrease by 15 minutes per press.
•Press to set the heating time for the selected day(s) and return to the
week line.
•Hold for 3s or wait for 10s to save and exit the heating time period
setting.
3.2.26 Press , ‘←’ and ‘→’ to check your week timer settings.
3.2.27 If heating needs to be turned off, it will be necessary to go back to the Normal Control
Mode to turn off.
Advance Mode (A)
3.2.28 Under the daily and week timer mode, Press :
3.2.29 To turn the heater off when the heater is on during a preset heating period.
3.2.30 To turn the heater on when the heater is off in between preset heating periods.
Adaptive Start Control
3.2.31 Accordingtoroomtemperature andsettemperature,theheaterwillautomaticallycome
on in time to heat the room to the set temperature at the set time. For example, if your
timer is set to start at18:00 and temperature is set to 23°C,the fire will come on at 17:30
to ensure the room is 23°C at 18:00.

13
Window Open Detection
3.2.32 When the transmitter detects a rapid drop in room temperature, it will be judged as a
window open, the warning icon will be displayed, and the heating will be turned off
automatically.
3.2.33 Aftertheindoortemperaturehasrisenoramanualoverrideofthewarning(byoperating
remote control) has been done, the fire will return to normal working state.
Set up the communication between the remote and appliance
3.2.34 The below operations should be carried out before programming, when changing to a
new remote or in the event the appliance cannot be controlled by the remote:
•Hold the reset button on the appliance for 3 seconds (pen point may be
needed) until you hear 3 short beeps from the unit, release the button.
•Press the button on the remote, the programming is finished when you
hear 1 long beep from the appliance.
3.2.35 Resetting the code for remote control is necessary if the appliance operates wrongly or
the remote control does not operate correctly.
•Open the back cover of the remote control.
•Press the Reset button on remote handset.
•Follow step 3.2.34
Resetting the Thermal Cut Out
3.2.36 The appliance is fitted with an Electronic Safety Control (E.S.). This is a safety device, which switches
off the fire if, for any reason, the appliance overheats, e.g.when covered. If the heater stops operating
while the flame effect continues working normally, this indicates that the E.S. Control is in operation.
The E.S. Control can only be re-set after the appliance has cooled down, and the appliance has been
reset. Re- setting of the E.S. Control proceeds is as follows:
3.2.37 Switch off the appliance (Manual On/Off switch) and leave it off for approximately 10-15 minutes.
3.2.38 Remove any obstruction to the fan heater outlet or fanblades etc. Make sure that the powersupply is
disconnected with the plug socket outlet while doing this.
3.2.39 Switch on the appliance and the E.S. Control will be re-set.
3.2.40 Ensure that the appliance is functioning correctly. If the E.S. Control operates again, the appliance
should be checked by a competent electrician.

SECTION 4: MAINTENANCE
Warning: Before any maintenance and/or cleaning the exterior of the fireplace, disconnect the
unit from the power supply and leave until cooled off.
4.1 Remote Handset Battery Replacement
Full battery
Half full battery
When the batteries are out of power and need replacing immediately
Battery replacement is recommended after 1 year. The batteries are 1.5V alkaline AAA batteries.
Dispose of old batteries at an appropriate recycling facility.
4.2 Cleaning the Fireplace
You can clean the exterior of the fireplace with a soft, damp, lint-free cloth. Do not use cleaning or
polishing products. To remove fingerprints or other marks on the front glass panel, use a soft, damp,
lint-free cloth with a good quality household glass cleaner. The front glass panel should always be
completely dried with a clean, lint- free cloth or paper towel.
Caution: Do not use abrasive cleaners on the glass panel. Do not spray liquids directly onto any
surface of the unit.
Caution: Other maintenance must be performed by a competent electrician.
4.3 Environment
Meaning of crossed –out wheeled dustbin:
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
Contact your local government for information regarding the collection systems available. If electrical
appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and
get into the food chain, damaging yourhealthand well-being. Whenreplacing oldappliances with new ones,
the retailer is legally obligated to take back your old appliance for disposals at least free of charge.
This fire complies with the Safety Standards EN 60335-1 and EN 60335-2-30 which covers the essential
requirements of the Low Voltage Directive 2014/35/EU and the EMC standards EN 55014-1; EN 55014-
2; EN 61000-3-2 and EN 61000-3-3 which covers the essential requirements of the European Electro
Magnetic Compatibility 2014/30/EU and the RED standards EN300220-2, EN301489-1, EN301489-3 and
EN6247 which covers the essential requirements of the European Radio Equipment Directive
2014/53/EU.
GIMEG Nederland B.V. –Atoomweg 99 –3542 AA –Utrecht –The Netherlands

15
NL HANDLEIDING
Belangrijk:
Lees de handleiding zorgvuldig door voordat u de elektrische open haard installeert of gebruikt, en
bewaar hem voor toekomstig gebruik. Deze handleiding maakt deel uit van het apparaat en moet bij
het apparaat worden bewaard. Als u het apparaat doorverkoopt, dient u deze handleiding bij het
product mee te leveren. Bij onjuist gebruik of het niet opvolgen van de veiligheidsinstructies is de
fabrikant niet aansprakelijk voor de gevolgen hiervan en vervalt het recht op garantie. Neem voor hulp
of aanvullende informatie contact op met een gekwalificeerde servicemonteur, de helpdesk of uw
verkoper.
DEEL 1: WAARSCHUWINGEN & ELEKTRISCHE GEGEVENS
1.1 Belangrijke veiligheidsinstructies
Dit symbool waarschuwt u voor mogelijke gevaren die u en/of anderen
kunnen doden of verwonden
NOOIT DOEN:
•Een beschadigde kachel installeren of gebruiken
•Het verwarmingselement veranderen
•De kachel gebruiken zonder volledig samenvoegen van alle onderdelen
WAARSCHUWING!
Onjuiste installatie, aanpassing, wijziging, service of onderhoud kan letsel of
materiële schade veroorzaken. Raadpleeg voor informatie de handleiding die bij deze
kachel zit. Voor hulp of meer informatie neem contact op met een erkende installateur,
een servicecenter of uw dealer.
WAARSCHUWING!
Bij gebruik van elektrische kachels moeten de voorzorgsmaatregelen altijd zorgvuldig
opgevolgd worden om het risico op brand, elektrische schok en persoonlijk letsel te
beperken.
•Gebruik deze kachel nooit in de onmiddellijke nabijheid van een bad, een douche of een
zwembad.
•Schakel de elektrische haard pas in totdat het goed is geïnstalleerd, zoals beschreven in de
handleiding (wel is het belangrijk om de haard te testen alvorens deze wordt ingebouwd).
•Laat de elektrische haard nooit branden terwijl u weg bent.
•Laat de elektrische haard nooit aangesloten op het stroomnet terwijl u weg bent.
•De elektrische haard is bedoeld voor huishoudelijk gebruik en mag niet worden gebruikt
voor industriële doeleinden.
•Gebruik de elektrische haard niet met natte handen.
•Gebruik de elektrische haard niet buiten.
•Gebruik de elektrische haard niet op of in de buurt van hete oppervlakten.
•De elektrische haard mag pas schoon gemaakt worden, als de elektrische haard is
ontkoppeld van het netstroom/stopcontact en als de elektrische haard volledig is
afgekoeld.
•Maak de elektrische haard nooit schoon met agressieve schoonmaakmiddelen.

16
•Gebruik nooit accessoires die niet zijn aanbevolen door Livn. Het kan gevaar opleveren
voor de gebruiker of schade aan de elektrische haard.
•Deze kachel moet geaard zijn. Neem bij twijfel contact op met een hiervoor bevoegd persoon.
•Gebruik deze haard niet als vrijstaand toestel. Het moet altijd aan de muur worden bevestigd.
•Om onbedoeld resetten van de thermische beveiliging te vermijden, dient dit toestel niet
te worden verbonden aan een externe schakelinrichting, zoals een timer of verbonden
circuit dat regelmatig aan en uit wordt geschakeld. Het toestel moet ten alle tijden direct
aangesloten worden op een wandcontactdoos.
•Deze kachel mag niet direct onder een stopcontact worden gemonteerd.
•Dit apparaat mag worden gebruikt door kinderen vanaf 8 jaar en ouder en personen met
verminderde lichamelijke, zintuiglijke of geestelijke vermogens of gebrek aan ervaring en
kennis mits onder begeleiding of als ze goed worden geïnstrueerd over het gebruik van
het apparaat op een veilige manier en ze begrijpen wat de gevaren zijn.
•Kinderen mogen niet met het apparaat spelen.
•Reiniging en onderhoud door kinderen boven de 8 jaar alleen onder toezicht.
•Kinderen onder 3 jaar moeten worden weggehouden van de kachel tenzij onder continue
begeleiding van een ouder.
•Kinderen tussen 3 jaar en 8 jaar mogen alleen het apparaat aan/uit zetten, mits deze
geïnstalleerd is zoals aangegeven in de handleiding en ze onder toezicht staan of worden
geïnstrueerd over het gebruik van het apparaat op een veilige manier en begrijpen wat de
mogelijke gevaren zijn. Kinderen tussen 3 jaar en 8 jaar mogen het apparaat niet
aansluiten, regelen of reinigen, of hier onderhoud op uitvoeren.
•Sommige delen van dit apparaat kunnen zeer heet worden en brandwonden veroorzaken.
Vooral kinderen en kwetsbare mensen moeten hiertegen beschermd worden door een
verantwoord persoon.
•Gebruik dit apparaat NIET in kleine ruimten waar mensen aanwezig zijn die de kamer niet
zelfstandig kunnen verlaten, tenzij er constant toezicht is.
•Bedek nooit de kachel, dit om oververhitting te voorkomen.
•Dit gemarkeerde figuur betekent: “WAARSCHUWING: NIET BEDEKKEN”.
•Gebruik de elektrische haard niet met een beschadigde stekker of snoer, na een storing,
na een val of wanneer de haard op enige wijze is beschadigd. Controleer regelmatig of het
snoer en de kachel geen beschadigingen hebben.
•Als de voedingskabel is beschadigd, moet deze door de fabrikant, een erkend
servicecentrum of een professioneel persoon worden gerepareerd.
•Om de kans op brand uit te sluiten, houd alle brandbare materialen (waaronder meubels,
gordijnen, textiel) op minimaal 1 meter afstand van het verwarmingselement.
•Zorg ervoor dat het netsnoer nooit over scherpe randen gaat, in aanraking komt met hete
oppervlakten of in de knoop komt.
•Laat het netsnoer niet draaien onder tapijten, karpetten etc.
•De stekker moet altijd bereikbaar blijven na installatie.
•Dompel het product nooit in water andere vloeistoffen.
•Sluit de elektrische haard niet aan op een tijdschakelaar of een stroomvoorziening die
regelmatig in- en uitschakelt door een programma.
•Koppel de haard niet los van de stroom wanneer deze in werking is. Gebruik de functies
van de afstandsbediening om de haard uit te schakelen en zorg ervoor dat de
hoofdschakelaar in de OFF (“o”) positie staat, voordat u de stekker uit het stopcontact
haalt.

17
•Houd het elektra snoer weg van het verwarmingselement. Begeleid het elektra snoer nooit
over de voorzijde van de haard.
•Gebruik de haard niet in een ruimte waar explosieve stoffen bewaard worden (zoals
petroleum).
•Gebruik dit apparaat NIET als er zichtbare tekenen van schade aan het apparaat zijn.
•Gebruik dit apparaat NIET als het is gevallen.
1.2 Specificaties
Model no. Dublin
Voedingsspanning: 220-240 V AC, 50 Hz
Maximaal verbruik: 2kW
Verbruik van vlameffect: 6,4W (LED 2,4W + Motor voor vlam 4W)
Verbruik van achtergrondverlichting: DC12V, Max 1,92W, 0,16A
Warmte opbrengst:
Nominale warmteopbrengst (Pnom): 2KW
Minimale warmteopbrengst (stand 1) (indicative) (Pmin): 1KW
Maximale warmteopbrengst (stand 2) (Pmax): 2KW
Elektriciteitsverbruik (zonder warmteopbrengst):
Bij nominale warmteafgifte (elmax): 12.5W
Bij minimale warmteafgifte (elmin): 12.0W
Stand-by modus (elSB): 0.48W
Type warmteafgifte / regeling van de kamertemperatuur
Single stage heat output and no room temperature control
No
Two or more manual stages, no room temperature control
No
With mechanic thermostat room temperature control
No
With electronic room temperature control
Yes
Electronic room temperature control plus day timer
Yes
Electronic room temperature control plus week timer
Yes
Andere besturingsopties
Room temperature control, with presence detection
No
Room temperature control, with open window detection
Yes
With distance control option
No
With adaptive start control
Yes
With working time limitation
No
With black bulb sensor
No

18
DEEL 2: INSTALLATIE
Benodigd gereedschap
Magnetische kruiskopschroevendraaier
Boormachine
Inhoud van de verpakking
Montagematerialen, afstandsbediening, batterijen, gebruikshandleiding, elektrische hanghaard.
2.1 Uitpakken van de haard
Waarschuwing! Gebruikhet apparaat nooit als een van de onderdelen nat is geweest. Neem
dan eerst contact op met een gekwalificeerd onderhoudstechnicus voor controle en/of
vervanging van elektrische onderdelen indien nodig. Houd de plastic verpakking uit de buurt
van kinderen.
•Open de verpakking voorzichtig en verwijder het schuim; controleer of het apparaat intact is, geen
tekenen van transportschade vertoont en of geen enkel onderdeel ervan blootgesteld is geweest
aan water. Neem het apparaat bij twijfel niet in gebruik en neem contact op met een erkend
servicecentrum.
•Verwijder de plastic zak en gooi deze weg.
•Wees verantwoordelijk bij het hanteren van het verpakkingsmateriaal.
•Bewaar de originele verpakking want u heeft deze misschien nodig als u een klacht heeft over het
product of als u het in de toekomst wilt transporteren en/of opslaan.
•Controleer of u alle onderdelen uit de verpakking heeft genomen voordat u de verpakking opbergt.
•Houd kleine kinderen uit de buurt voor en tijdens de installatie. Laat kleine kinderen niet in
aanraking komen met de losse onderdelen tijdens montage.
•De elektrische haard kan bijna overal in huis geplaatst worden. Lees en volg de instructies
zorgvuldig bij het kiezen van een locatie. Voor het beste resultaat, installeer de elektrische haard
niet in direct zonlicht.
•Sluit het apparaat aan op een geaard stopcontact dat goed toegankelijk is, zodat u het apparaat
gemakkelijk kunt loskoppelen.

19

20
2.2 Afmetingen hanghaard (in mm)
2.3 Montage hanghaard
•Het is aanbevolen dat minstens 2 of meer mensen de elektrische haard installeren.
•Zet de elektrische haard pas aan nadat het apparaat goed is aangesloten en de instructies
volledig zijn gelezen.
•De elektrische haard moet in de buurt worden geplaatst bij een geschikt, geaard stopcontact. Het
stopcontact moet gemakkelijk toegankelijk zijn.
STAP 1. Zoek een veilige locatie. Minimale vrije ruimte aan de linker- en rechterkant moet ten minste
100 mm zijn; minimale afstand van het plafond moet minimaal 200mm zijn; minimale afstand van
de vloer moet minimaal 400mm zijn; minimale afstand van de voorkant moet minimaal 100 cm zijn.
Kies een locatie in de buurt van een stopcontact zodat een verlengsnoer niet nodig is. Gebruik de
haard niet direct onder een stopcontact.
STAP 2. Kies een stevige en vlakke muur en plaats de montagebeugel op de gewenste positie.
Markeer met een pen de 4 bevestigingsgaatjes van de beugel op de muur.