LLOYTRON A1210WH User manual

MODEL: A1210WH
OPERATING INSTRUCTIONS
2000w Remote
Controlled Socket Set

2
thank you
Thank you for the purchase of this quality LLOYTRON product. Used carefully and in accordance with the
instructions enclosed, it should give you trouble free service over a long period of time. Please keep these
instructions for future reference.
FEATURES
This pack contains 2 wireless controlled plug sockets, which allow you to remotely switch on and off table
lamps or appliances with power requirements up to 2000w.They are very simple to setup, just plug into
the electric socket you want to control and set the socket to the required remote button. You can then
control the socket from up to 30 metres away with the remote control. You can set each of the 2 sockets
on different RF channels to be individually controlled, or on the same RF channel so that all 2 sockets can
be controlled at same time.
FUNCTION
• Ideal to control hard-to-reach sockets to switch appliances on and off.
• Several sockets can be controlled at same time.
• 4 individual code selections to avoid interference with other units.
• The LED on the Remote Control can indicate the signal transmission status.
• Both Remote Control and Receivers (Sockets) have 4 channels and 4 frequency codes.
• Up to 16 Receivers (Sockets) can be added.
IMPORTANT SAFEGUARDS AND PRECAUTIONS
SAVE THESE INSTRUCTIONS
• Do not use more than 2000w power consumption.
1) LED LIGHT 2) ON/OFF CHANNEL BUTTONS
3) LED LIGHT 4) CODE ADJUSTMENT SETTING
5) UK SOCKET 6) BATTERY COMPARTMENT
7) CODE ADJUSTMENT SETTING 8) CHANNEL / BUTTON SETTING
9) UK PLUG
LOCATION OF CONTROLS

3
WEEE/ENVIRONMENTAL PROTECTION
Disposal of Electrical and Electronic Equipment
Do not dispose of this product with household waste. For the proper treatment, recovery and
recycling please take this product to the appropriate waste collection point. If you are unsure
where this may be, please contact your local authority. Improper disposal may be harmful to
the environment.
1) Insert 1x A23S Battery (supplied) into the remote control.
2) Set the code and channel of the remote control and sockets to the desired setting.
3) Plug the electrical appliance (No more than 2000w rated) into the desired reciever (socket).
4) Press the corresponding channel number on the remote control to operate the socket ON and OFF.
Note: Always check that the reciever (socket) is switched on and the wall socket before use.
HOW TO USE
• Remote Control Battery: A23S 12v 23 A
• Remote Control Radio Frequency: 433.92 Mhz
• Receiver Voltage: 220-240v~50Hz
• Receiver Maximum Wattage: 2000w (Socket)
• Transmission Range: Typically 30m (Open Area)
SPECIFICATION
Code Adjustment Setting
The code is to avoid interference from other remote controlled socket transmitters.
The code on every socket should be the same as the code set on the remote control.
Therefore if the code set on the remote control is III, then the 2 sockets in this pack should be set to III.
NOTE: Codes should be changed if you meet interference with similar unit.
RF Channel / Button Setting
The RF channel adjustment is to set each socket to the required button press.
To switch on and off Socket 2, then the socket should be set to 2 etc.
Multiple sockets can be given to the same RF channels, so that by the press of one button, several sockets
will operate at the same time. If each socket is given an individual RF channel, then each socket requires a
different button press.
CODE & CHANNEL ADJUSTMENTS

call: 08454 81 8808
email: [email protected]
web: www.lloytronhelpdesk.com
If you have any queries about this product, there are three ways to contact our customer service department:
To nd more details on a wide range of Lloytron products please visit our website at www.lloytron.com
Lloytron plc, Laltex House, Leigh Commerce Park, Greenfold Way, Leigh, Lancashire, WN7 3XH. England, U.K
CUSTOMER SERVICES
2011/65/EC