LOEHR L2 ENO User manual

1
• Frame assembly: The main beams (A)
are placed in the sockets of the leg
frames (C). It is recommended that you
first connect one beam and one leg
(see step 2), then place the second leg
on the other end of the beam. Finally,
the second beam can be placed on the
already standing frame and fastened.
• The spacer fittings (B) are placed
between the beam (A) and the mounting
plate (C) of the respective leg frame.
2
• Fasten the leg frames with four screws
(M8x16) each per mounting point.
3
• From the underside, the leg frames are
additionally fixed to the main beams
with a screw (M8x16).
L2ENOASSEMBLY INSTRUCTIONS
BA C
4x
4x
4x
B
B
B
B
A
A
C
C
C
C

4
• The frame can now be positioned and
aligned.
• The height-adjustable feet can be used to
level out any unevenness in the floor.
• Then place the table top and align the
screw positions along the main beams.
5
• Now fix the table top to the frame from
the underside with nine screws (M8x16)
per main beam.
L2ENOASSEMBLY INSTRUCTIONS

6
• Then mount the rails for the cable duct
covers (D) with three screws per rail
(M5x12).
7
• Now the cable management is installed.
• It is recommendable to equip the cable
baskets with socket strips etc. before
mounting.
• The parts with the lateral surfaces (E) are
positioned under the cable outlets in the
tabletop.
• The slots in the cable basket allow the
electrics to be secured.
• The large holes in the bottom of the cable
baskets should be kept free for mounting,
but can also be utilised as cable outlets
as needed during later use.
8
• The cable baskets are fixed with four
screws (M8x16) each at the intended
positions.
L2ENOASSEMBLY INSTRUCTIONS
D
E4x

9
• Place the cable duct covers over the
cable outlets.
10
• The table is now usable.
L2ENOASSEMBLY INSTRUCTIONS
ENJOY!

11
• One leg frame is mounted in the regular
way (F, see steps 1-3), the other leg frame
(G) is fastened with the connector fittings
(H) instead of spacer fittings (see step 1,
component B). Like the spacer fittings,
these sit between the main beam and the
mounting plate of a leg section.
• The mounting point at the end of a main
beam is used (I).
12
• Use two of the bolt points on the
mounting plate to connect the leg frame
to the main beam (M8x16).
• Then use the four regular screw points
(M8x16) for the leg frame to connect the
connector fitting to the main beam there.
L2ENOASSEMBLY INSTRUCTIONS
WORKBENCH COUPLING
F
H
G
HI
2x
2x
I
ATTENTION: Please pay attention to
the colour markings of the parts and
match them correctly to guarantee a
perfect fit.
!

13
• Place the frame to be coupled at the
other side of the junction and fasten it
(see steps 11-12).
• Align the entire frame.
14
• When installing cable management,
a bridge basket (J) is inserted across
the junction. Its central bracket fits to
the crossbeam of the leg frame at the
junction.
• The bridge basket is inserted before the
table tops are mounted.
L2ENOASSEMBLY INSTRUCTIONS
WORKBENCH COUPLING
ATTENTION: Any number of frames
can be coupled together. If more
than two frames are lined up, steps
11-14 are simply repeated.
!
J

15
• Now all the table tops are placed and
bolted (see steps 4-5).
16
• At the junction, the connector fittings are
fixed to the table tops (M8x16) (K).
• Under the cantilevering sides of the
tabletops, two additional connecting
plates are mounted across the junction,
connecting the table tops (M8x16) (L).
• The bridge basket is also fastened to the
tabletops from below, in the same way as
the regular cable baskets.
• For the installation of the standard cable
management, see steps 6-8.
L2ENOASSEMBLY INSTRUCTIONS
WORKBENCH COUPLING
K
L
L
4x

L2ENOASSEMBLY INSTRUCTIONS
WORKBENCH COUPLING
02-2022
[e-mail] [phone]LOEHR.CO
17
• Place the cable duct covers over the
cable outlets.
18
• The ENO workbench is now usable.
ENJOY!