Logic ZOOM User manual

:: 4.3” Display ::
QuickStart Guide www.logicpd.com

ZOOM 4.3” Display
QuickStart Guide
We fast forward
the evolution of
new products.

1 Introduction
Congratulations on your purchase of the Zoom™ 4.3” Display
Kit. The 4.3” LCD connects directly to Logic’s Zoom SDK and LV
baseboards allowing you to immediately begin development work.
1.1 Zoom 4.3” Display Kit Features
+ 4.3” WQVGA TFT LCD with touch screen
+ 60-pin LCD connector to interface with baseboard
1.2 Register your Display Kit
Registration provides you access to the latest revision of this
manual, as well as other documentation and resources. In addition
to downloads access, registration provides future notifications when
Logic releases documentation and updates for your product.
To register, visit the Logic Support website at
http://www.logicpd.com/product-support and click on “Register Your
Kit”. Follow the on-screen instructions to register your product.

2 Connect LCD to Baseboard
Locate the 60-pin LCD connector on your baseboard (reference1.
designator J11).
Align the keyed connector on the LCD board with the baseboard
2.
60-pin LCD connector.
Press straight down on the LCD board until the baseboard3.
connector levers move into a vertical position. Note: Use caution
when pressing down on the LCD board as the solder points may
be sharp.

Before using the LCD touch screen, remove the protective4.
plastic film covering the display.
To remove the LCD board from the baseboard, pull back on the
5.
ejector levers until the connector on the display board moves up
and disengages from the baseboard 60-pin LCD connector.
2.1 Baseboard Jumper Settings
If you are attaching the display to an LV baseboard (as pictured in
step 3), verify that jumper JP1 is placed across pins 2 and 3.
If you are attaching the display to an SDK baseboard, verify that
jumpers J6 are placed on pins 5 and 6.
1
2
6
5
+–
1
2 6
5
+–
Normal Operation JTAG Operation
J6 J6
5
6
1
JP1
3

3 Interact with Display
Connect the development kit to a host PC as described in the1.
appropriate Zoom Development Kit QuickStart Guide.
Open the Tera Term application or equivalent software terminal
2.
emulation tool. Use the proper Serial Port Settings as explained
in the appropriate Zoom Development Kit QuickStart Guide.
Apply power to the development kit.
3.
To initialize the screen, type the following command at the losh>4.
prompt and press the Enter key: video-open 15 16
To display a test image on the screen like that shown below,
5.
after the video-open command has been entered, type the
following command at the losh> prompt and then press the
Enter key: draw-test

4 Product Notices
Evaluation Purposes Only
This Zoom Display Kit being sold by Logic is intended for
ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES
ONLY and is not considered by Logic to be fit for commercial use.
As such, the goods being provided may not be complete in terms of
required design, marketing, and/or manufacturing related protective
considerations, including product safety measures typically found
in the end product incorporating the goods. The user assumes all
responsibility and liability for proper and safe handling of the Display
Kits.
ESD
Due to the open construction of the product, it is the user’s
responsibility to take any and all appropriate precautions with regard
to electrostatic discharge. Logic’s warranty does not cover products
damaged by ESD.

5 Support
5.1 Documentation and Software Downloads
Logic provides additional documentation and resources for the 4.3”
Display Kit. These resources are available as downloads from the “My
Account” section of the Logic website. Click on the “Login” link at
the top of any www.logicpd.com web page and enter your username
and password to access the available downloads for the 4.3” Display
Kit.
5.2 Frequently Asked Questions
Visit www.logicpd.com/product-support/frequently-asked-questions-
faq for FAQs regarding the 4.3” Display Kit.
5.3 Technical Discussion Group
Visit http://www.logicpd.com/product-support to join our Technical
Discussion Group (TDG) and share valuable information with other
designers. Please note that the TDG site requires its own account
creation that is separate from the account for the main Logic website.
5.4 Warranty Statement
Refer to the card enclosed with the 4.3” Display Kit for warranty
information.

6 Revision History
REV EDITOR REVISION DESCRIPTION APPROVAL DATE
A
PN 1012053
JCA Initial release EGR 04/23/09

Logic PN 1012053A
© 2009 All rights reserved. Logic Product Development Company. Zoom and LogicLoader are trademarks of Logic
Product Development Company. Terms and product names in this document may be trademarks of others.
Logic Product Development Company makes no warranty for the use of its products. The Company assumes no respon-
sibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed
herein at any time without notice, and does not make any commitment to update the information contained herein. The
names of the sample source code files and the platform dependent environment variables may be subject to change
without notice. Some steps and figures may vary between different versions of tools. No licenses to patents or other
intellectual property of Logic are granted by the company in connection with the sale of Logic products, expressly or by
implication.
embedded product solutions
411 N. Washington Ave. Suite 400 Minneapolis, MN 55401
T : 612.672.9495 F : 612.672.9489 I : www.logicpd.com