Logmaster WLS520-A User manual

Instruction
Instruction
Instruction
Instruction Manual
Manual
Manual
Manual
heck
heck
heck
heck
Model
Model
Model
Model WLS520-A
WLS520-A
WLS520-A
WLS520-A
REF.
REF.
REF.
REF. #:
#:
#:
#: D
D
D
D 1402
1402
1402
1402
MODEL
MODEL
MODEL
MODEL 7TWLS520-A
7TWLS520-A
7TWLS520-A
7TWLS520-A
REF.
REF.
REF.
REF. #:
#:
#:
#: D
D
D
D 1917
1917
1917
1917

Please read the manual first. It will help you assemble, prepare, operate and maintain the unit for best
performance. Pay special attention to the safety instructions before operating. For future reference , please
copy the model number and the serial number of the equipment you purchased in the space below.
Model Number:
Serial Number:
If you have difficulty or any problems regarding the assembling, operation or maintenance of this unit,
please call customer support of an authorized dealer or the manufacturer.
Distributed by: BVG-Airflo Group plc, Unit 6, Industrial Estate, Brecon, Powys, LD3 8LA . After Sales
Customer Service Telephone: [phone] Fax: [phone]
Table
Table
Table
Table of
of
of
of Contents
Contents
Contents
Contents
SECTION 1: Know your log splitter
1. Machine overview ּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּ
2. Accessories ּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּ
3. Decals on machine ּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּ
4. Superiority of your log splitter ּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּ
5. Technical specifications ּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּ
6. Component parts diagram ּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּ
7. Electric circuit principle diagram ּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּ
8. Hydraulic circuit principle diagram ּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּ
SECTION 2: Safe operating instructions
1. Assembling your log splitter ּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּ
2. Preparation before operating ּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּ
3. Operation ּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּ
4. Transportation ּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּ
5. Maintenance and repair ּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּ
6. Storage ּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּּ
1
1
1
1
2
2
2
4
4
5
6
6
7
7
8
8
8
9

SECTION
SECTION
SECTION
SECTION 1:
1:
1:
1: Know
Know
Know
Know Your
Your
Your
Your Log
Log
Log
Log Splitter
Splitter
Splitter
Splitter
1.
1.
1.
1. Machine
Machine
Machine
Machine overview
overview
overview
overview
1.
Hydraulic tank
2. Wedge
3. Ram
4.
Log cradle
5. Electric motor
6. Connecting box
7.
S witch
8. Power cable and plug
9. Wheel
10.
Control handle
11. Front frame
12. Towing handle
13.
Vent plug
14. Oil dipstick
2.
2.
2.
2. Accessories
Accessories
Accessories
Accessories
1.
Copper seal at dipstick × 1
2. Hex wrench × 1
3. Screw, washer and nut × 4
4.
Safe guard × 2
5. Control handle bar × 2
6. Operator ’ s manual × 1
3.
3.
3.
3. Decals
Decals
Decals
Decals on
on
on
on machine
machine
machine
machine
Locate model plate and safety label on the equipment. Read and follow the instructions in them.
Model plate (WLS 52 0- A ) Model plate ( 7T WLS520- A )
Note: S6 %40, continuous operation periodic duty: time of one load cycle is 10 minutes,
o peration time at constant load is 4 minutes, operation time at no-load is 6 minutes.
WEEE label
2
2
2
2
1)
The left figure means: Do not abandon the waste product
freely; the product should be sent to relevant recycle
organization.
2)
Dispose of the packing in the proper manner. Should you wish
to part with the product, dispose it in accordance with the
latest provision. Regarding the detail information, please refer
to us.

Safety label
Symbols meaning
4.
4.
4.
4. Superiority
Superiority
Superiority
Superiority of
of
of
of your
your
your
your log
log
log
log splitter
splitter
splitter
splitter
Compact and powerful, the latest electric/hydraulic log splitter features a 1960 / 2900 W motor that packs a
whopping 4, 7 ton of splitting force . It can slice logs up to 520mm long and 250mm in diameter easily. Unlike a
gas-powered splitter, there are no loud noises and no fumes . It ’ s an ideal choice for homeowner to use indoors
or outdoors. It ’ s small and lightweight enough for one person to easily move about. It will even fit in the trunk of
your car. In addition, our technical improvements make this unit more durable, convenient, efficient, and safe for
all operators.
3
3
3
3
Read the manual carefully
before assembly, operation
and maintenance.
Wear safety gloves.
Wear safety shoes or heavy
boots.
Wear a protection mask or
protective eye wear.
Don ’ t touch rotating parts.
Caution: Pinch point.
Warning: Moving parts. Never place
body between log and ram during
forward or reverse stroke.
Allow only one person to operate this
machine on the workbench, keep
bystanders away.
Never remove stuck log or clean the
knife bare-handed.
Maintenance, installation, adjustment
and cleaning of the machine only once
the power supply is disconnected
according to the instructions in this
manual.

5.
5.
5.
5. Technical
Technical
Technical
Technical specifications
specifications
specifications
specifications
4
4
4
4
Technical specifications
WLS520 -A
7TWLS520 -A
Electrical
Requirement
Voltage
230V ± 10%
230V ± 10%
Frequency
50 Hz ± 1%
50 Hz ± 1%
HVF
＜0.02
＜0.02
Power input
1960 W
2900W
Power output
1500 W
2200 W
Rated current
8.5A
12A
Motor speed
2800 rpm
2800 rpm
Thermal protector
130 ℃
130 ℃
Protection degree
IP 4 4
IP 4 4
Motor working mode
S 6 40%
S 6 40%
Power cable
3G1. 5 mm ²
3G1.5mm ²
Technical specifications
WLS520-A
7TWLS520-A
Machine dimension (L × W × H) (cm)
97 x 28 x 46
97 x 28 x 46
Machine net weight
47.5 kg
50kg
Min. o il capacity
3.2 Liter
3.4Liter
Max. splitting force
4 ton
7ton
Max. splitting length
520 mm
520mm
Max. splitting diameter
25 0mm
25 0mm
Hydraulic pressure
16 MPa
28MPa
Cylinder inner diameter
55 mm
55 mm
Feed time
10s
10s
Retract time
4s
4s
Max. cylinder stroke
520mm
520mm
Noise emission value
≤ 68dB(A)
≤ 68dB(A)
Vibration of control handle
≤ 2.5m/s
2
≤ 2.5m/s
2
Environmental data
WLS520-A, 7TWLS520-A
Operation
Altitude
≤ 1000m
Temperature
5~40 ℃
Humidity
40 ℃
≤ 50%
20 ℃
≤ 90%
Transportation & storage t emperature ( ℃)
-25~+50

6.
6.
6.
6. Component
Component
Component
Component parts
parts
parts
parts diagram
diagram
diagram
diagram
5
5
5
5
Note:
Note:
Note:
Note: Due to continuous product improvement, we
reserve the right to change the product without prior
notice.

7.
7.
7.
7.
Electric
Electric
Electric
Electric circuit
circuit
circuit
circuit principle
principle
principle
principle diagram
diagram
diagram
diagram
A.
Power cable
B.
Switch
C. Wiring board
D.
Motor lead wire
E.
Thermal protector
F. Main winding
G.
Aux. w inding
H.
Capacit or
8.
8.
8.
8. Hydraulic
Hydraulic
Hydraulic
Hydraulic circuit
circuit
circuit
circuit principle
principle
principle
principle diagram
diagram
diagram
diagram
A.
Hydraulic tank
B.
Oil filter
C. Oil pump
D.
Electric motor
E.
Relief valve
F. Control handle
G.
Cylinder
6
6
6
6
Ref. No.
Part Description
Ref. No.
Part Description
1
Optional four way wedge
41-44
Oil tube assembly (tank -pump)
2
Tank with wedge
45-47
Hydraulic pump assembly
3
Oil filter
48-51
Motor rear plate assembly
4
Ram
52
Motor shell
5
Nylon liner
53
Stator
6-9
Base plate assembly of ram
54
Rotator
10-13
Log cradle assembly
55, 70-72
Connecting box assembly
14
Front paper seal ring
56-60
Key switch assembly
15-18
Piston and seals
61-66
Capacitor assembly
19 ― 21
Piston shaft
67-68
Cable fastener assembly
22
Retracting spring
69
Power cable
23
Hydraulic cylinder
73-76
Motor front plate assembly
24
2-end long bolt
77-78
Fan assembly
25
Front cylinder cover
79-81
Fan cover assembly
26
Vent plug
82-87
Front frame assembly
27
Seal ring
88-92
Towing handle assembly
28
Dust-proof ring
93-95
Wheel assembly
29-30
Dipstick assembly
96-99
Wheel frame assembly
31
Rear paper seal ring
100-103
Control handle assembly
32-36
Hydraulic valve assembly
104-106
Shield assembly
37-40
Oil tube assembly ( valve – pump)
107-110
Safe guard assembly
Note:
Note:
Note:
Note: The mains connection must have maximum 16A fuse .

SECTION
SECTION
SECTION
SECTION 2:
2:
2:
2: Safe
Safe
Safe
Safe Operating
Operating
Operating
Operating Instructions
Instructions
Instructions
Instructions
NOTE: This machine is only intended for homeowners to split firewood as detailed in instructions, not for any
other purpose.
Danger
Danger
Danger
Danger This machine was built to be operated according to the safety instructions in this manual. As with
any type of power equipment, carelessness or error on the part of operator could endanger the personal safety
and/or property of yourself and others. It ca n result in serious injury or death, such as amputating hands or feet,
throwing objects and other unforeseeable damage. Read and follow all instructions before initial operation. The
manufacturer isn ’ t liable for any damages by disregard of the instructions.
1.
1.
1.
1. Assembling
Assembling
Assembling
Assembling your
your
your
your log
log
log
log splitter
splitter
splitter
splitter
•
Cut and remove straps bound to the carton and
unpack the carton.
•Remove the loose parts included with unit (i.e.,
operator ’ s manual, parts assembly, etc.).
•Set the foams aside.
•Connect control handle bars. Pivot each control
handle bar to its linkage part in rear of the splitter
and tighten. ( Fig.
Fig.
Fig.
Fig. 1
1
1
1)
•Connect the safe guards. Align the holes in the
safe guards with main shield, secure with wrench
and screwdriver. ( Fig.
Fig.
Fig.
Fig. 2
2
2
2)
NOTE:
a)
Dispose of the packing in an environmental friendly manner. Take to a proper collecting point.
b) If you notice transport damage while unpacking, notify your supplier immediately. Don ’ t operate the
machine.
c)
Read, understand and follow all safety instructions in this manual and labels on the equipment carefully.
d) Keep the manual in a safe place for future and regular reference.
e) Ensure the machine is disconnected from power supply while assembling.
2.
2.
2.
2. Preparation
Preparation
Preparation
Preparation before
before
before
before operating
operating
operating
operating
•
•
•
•Put the machine on the level surface of a sturdy workbench 60
+
cm high.
•
•
•
•
Always block the wheels to prevent movement of the log splitter while in operation.
•
•
•
•Oil the wedge and upper side of the tank, which would make your operating more smoothly.
•
•
•
•Check all nuts, bolts and hydraulic fittings are tight to be sure the equipment is in safe working condition.
•
•
•
•
Make sure your outlet, mains voltage and frequency match the data stated on the model
plate (or “ Technical specifications ” in this manual).
•
•
•
•The power supply for this splitter must have the protection device of under-voltage, over-voltage, circuit
breaker with a residual current device (RCD) which maximum residual current rated at 0.03A.
•
•
•
•Check the switch, power cable and plug are not damaged (no cracks, etc.) to exclude the risk of electric
shock and circuit short.
•
•
•
•
Check all safe shields to be sure they are in the proper position.
•
•
•
•Wear non-slip safety shoes, safety goggles, safety gloves and suitable work clothing. Never wear jewelry,
necktie and other loose clothing.
•
•
•
•
Logs should be cut with square ends and permissible dimensions in advance within the limited capacity .
Uneven log ( e.g. knotted, curved, etc) should not be cut.
Note:
a) Make sure the power cable is unplugged while adjusting.
b)
After adjusting, take away the accessories on or around the unit before switching on.
c) Ensure the motor properly earthed or apply protection device.
d) Use only rubber-jacketed cable of sufficient lead cross section as extension cable. Never use an extension
cord longer than 25 feet. Cord gage must be 14 or lower.
e) Keep away from inflammable liquids or gases before starting the machine.
f) Hydraulic oil is flammable and can explode. Always take a Class B fire extinguisher with you when
operating this log splitter in dry area as a precautionary measure against possible flying sparks.
g) Always check the oil level of the hydraulic reservoir before operation. Operating the log splitter without an
adequate oil supply will cause severe damage to the pump.
h)
Keep handles free of oil, grease and resin.
7
7
7
7
Fig.
Fig.
Fig.
Fig. 1
1
1
1
Fig.
Fig.
Fig.
Fig. 2
2
2
2

i)
Before starting work, hydraulic pipes and hoses shall be inspected and the stopping devices should be
tested.
j)
Selection and preparation of a suitable working are free from obstructions.
k)
The need to keep the working area free from obstructions, e.g. logs, split wood, etc.
l)
Check on the function of the machine: operate the unit without loading to check whether this unit works
normally (Refer to terms 3.
3.
3.
3. Operation
Operation
Operation
Operation below). If the noises becoming louder and the ram running erratic
indicate there ’ s excessive air or a shortage of hydraulic oil in tank for you to release vent plug or add
hydraulic fluid.(Refer to Term 5. Maintenance and repair)
3.
3.
3.
3. Operation
Operation
Operation
Operation
NOTE:
a)
After log splitting, switch off and unplug the power cable.
b) Ensure the horizontal distance between splitter and outlet is more than 3m in case of the dust influence.
c) Allow only responsible adults who have read and understood the manual to operate this machine.
d)
Be familiar with all controls and proper operation. Know how to stop the machine quickly in the event of an
emergency.
e) Don ’ t operate the machine while under the influence of alcohol, drugs or medication.
f)
Only a single operator is allowed to load and operate this log splitter. Keep bystanders, helpers, pets and
children a sufficient distance to the machine.
g) Only use your hands to operate the control handles and the switch. Arms, feet, knees, rope, heavy objects
and extension device are not allowed.
h) Never put any part of your body between the extending ram and the wedge.
i) Don ’ t step over the splitter when the motor is running.
j)
Always split log along its grain. If across the grain, some types of wood may burst or fly out resulting in
injury.
k) If you experienced problems splitting especially hard wood, don ’ t keep pushing on the handles. Release
both control handles at once, the ram will return. If keep pushing, the ram will fail to retract. If this occurs,
turn off the motor and on again to continue operation.
l) If the log is clipped on the wedge, release both hands and unplug the power cable immediately . Knock off
the log with a hammer slightly (not with your hands).
m) Never attempt to split more than one log at a time unless the ram has fully extended and a second log is
needed to complete the separation of the first log. Never attempt to split one log on top of another.
n)
Regularly clear the split wood to keep work area tidy for firm footing.
o) Periodically check that all nuts, bolts, screws, hydraulic fittings and hose clamps are tightened.
p) Never operate your splitter on wet, muddy or icy surface. Safe footing is essential in preventing accidents.
q)
Never leave the machine unattended with the motor running.
r) Never use this machine in damp or rainy environment to avoid electric shock or short circuit.
s) Operate log splitter in proper lighting.
t)
Never tamper with the motor to run it at excessive speeds. The maximum motor speed is preset by the
manufacturer and is within safety limits.
u) Switch off and unplug power cable quickly when the machine is out of order. For example: the noises
becoming louder and the ram running erratic indicate there ’ s excessive air or a shortage of hydraulic oil in
tank for you to release vent bolt or add hydraulic fluid.(Refer to Term 5. Maintenance and repair)
v) Don ’ t pull on power supply cable to unplug.
4.
4.
4.
4. Transportation
Transportation
Transportation
Transportation
•
Put in the trunk of your car for a distant transportation.
•Hold the towing handle to move about.
NOTE:
a) Never move this machine while the motor is running.
b) Be extra cautious when moving this machine on rugged and rough terrain.
c)
Be careful to keep upright, not to be tipped or crashed during transportation
d) Never allow anyone to ride on the machine while moving.
8
8
8
8
•
Plug the power cable and switch on.
•
•
•
•
Load log between log cradles and on the tank. (Fig.
(Fig.
(Fig.
(Fig. 3)
3)
3)
3)
•
Move control handles down with both hands until the log
is sp l it . (Fig.
(Fig.
(Fig.
(Fig. 4)
4)
4)
4)
•
Release any hand to stop the ram extending.
•
Release both hands to retract the ram for
loading next log.
•
After log splitting, switch off and unplug the power cable.
Fig.
Fig.
Fig.
Fig. 3
3
3
3
Fig.
Fig.
Fig.
Fig. 4
4
4
4

5.
5.
5.
5. Maintenance
Maintenance
Maintenance
Maintenance and
and
and
and repair
repair
repair
repair
•
•
•
•
Refer to the Components drawing and parts list should it become necessary to disassemble the unit for
repair or replacement of parts.
NOTE:
a)
Ensure the power cable is unplugged while performing any maintenance and repair.
b) The hydraulic system is preset at the factory. Don ’ t adjust the valve.
c) Never alter this machine in any manner under any circumstances. Any alteration circumventing the design
capabilities and capacities of this machine could result in serious injury and will void the warranty.
d) Replace all damaged and worn parts immediately with original equipment and manufacturer ’ s parts
only.
e) Wipe unit with an oiled rag to prevent rust. If the wedge becomes dull or nicked, it can be sharpened.
Wear safety gloves while handling the wedge.
f) Never check for leaks of hydraulic fluid with your hand. Escaping fluid under pressure can have sufficient
force to penetrate skin causing serious personal injury or even death. Leaks can be detected by passing a
piece of cardboard over the suspected leak and looking for discoloration.
g) Never loosen or remove hydraulic fittings or the cap of hydraulic tank while the log splitter is running.
h) If the motor i s overload for a long time, the thermal protector in it which operating temperature is
1 30 °C will disconnect the power of motor. Switch off and unplug the power cable, cool down the motor for
half an hour and it will connect again for continual operation. If not, it ’ s necessary for you to call your dealer
for customer support.
i)
The troubles of hydraulic system and motor other than described above should only be handled by
qualified specialists.
j) Periodically check the oil level in the hydraulic reservoir. If there ’ s a slow or erratic ram running during
operation, it indicates the problem of oil shortage or excessive air in the reservoir. T o solve this problem,
please refer to the following Term 5. l).
k) After each season use, check if the hydraulic oil need to change. Generally, this log splitter has oil filter in
the tank, so just change the oil when there ’ s abnormal louder noise or ram block during operation. T o solve
this problem, please refer to the following Term 5. l).
l) Directions:
Directions:
Directions:
Directions: how
how
how
how to
to
to
to changing
changing
changing
changing hydraulic
hydraulic
hydraulic
hydraulic oil,
oil,
oil,
oil, fill
fill
fill
fill the
the
the
the hydraulic
hydraulic
hydraulic
hydraulic reservoir
reservoir
reservoir
reservoir and
and
and
and repel
repel
repel
repel the
the
the
the excessive
excessive
excessive
excessive air
air
air
air in
in
in
in
the
the
the
the reservoir.
reservoir.
reservoir.
reservoir.
Note: The hydraulic tank is shipped with 10W AW hydraulic fluid. If it is difficult to obtain, Dexron Ⅲ
automatic transmission fluid can be substituted. You must drain the system. Don ’ t mix Dextron and 10W
hydraulic fluid. Use only clean oil and take care to prevent dirt from entering the hydraulic reservoir.
6.
6.
6.
6.
Storage
Storage
Storage
Storage
NOTE:
a)
Store this unit switched off and unplugged.
b) Allow machine to cool 5 minutes after every use before storing.
c) Protect power supply cable from heat, sunshine, aggressive liquids and sharp edges.
d)
Store unit in a clean, dry area. Don ’ t store it unprotected outdoors, next to corrosive materials or in damp
environment .
e) Store this splitter where children can ’ t start it.
9
9
9
9
•
Disconnect the safe guards from the main shield
and take off the cushions from front frame.
•
Lift the towing handle and keep the tank in vertical
position. (Fig.5)
(Fig.5)
(Fig.5)
(Fig.5)
•
Disconnect the vent plug and dipstick from the
front cylinder cover. (Fig.
(Fig.
(Fig.
(Fig. 5)
5)
5)
5)
•
I f you want to change the oil, please drain the tank firstly .
Put the front frame of the unit in some container, raise
the wheels 5cm off the ground on blocks, and drain the
hydraulic tank. (
(
(
( Fig
Fig
Fig
Fig .
.
.
. 6)
6)
6)
6)
•
Deposit the hydraulic fluid for refilling or change
new hydraulic oil (10W AW hydraulic fluid or Dexron Ⅲ
automatic transmission fluid).
•
Refill the tank at least the range marked on the
dipstick. If the tank permits, more oil added will do
good to the hydraulic system for better operation.
•
After refilling, insert and tighten the dipstick.
•
Start the motor and operate the log splitter fully
extended for several times to repel out the air in the
reservoir.
•
When make sure the oil level is OK and no excessive air
in the tank, insert and tighten the vent plug.
Fig.
Fig.
Fig.
Fig. 5
5
5
5
Fig.
Fig.
Fig.
Fig. 6
6
6
6

10
10
10
10
GUARANTEE
GUARANTEE
GUARANTEE
GUARANTEE
IMPORTANT
IMPORTANT
IMPORTANT
IMPORTANT
Please
Please
Please
Please do
do
do
do not
not
not
not return
return
return
return this
this
this
this product
product
product
product without
without
without
without first
first
first
first
calling
calling
calling
calling the
the
the
the Customer
Customer
Customer
Customer Service
Service
Service
Service number
number
number
number below:
below:
below:
below:
0870
0870
0870
0870 888
888
888
888 1008
1008
1008
1008
Thank you for purchasing this product, which has been made to demanding high quality
standards and is guaranteed for domestic use against manufacturing faults for a period of
12 months from the date of purchase.
This guarantee does not affect your statutory rights. If your product fails due to a defect in
material or workmanship during this period, please return it to the place of purchase.
Normal wear and tear is not covered under the guarantee.
Any guarantee is invalid if the product has been misused or subject to neglect or an
attempted repair other than by our own service centre.
Due to continuous product improvement, we reserve the right to change the product
specification without prior notice.
After
After
After
After Sales
Sales
Sales
Sales Customer
Customer
Customer
Customer Service:
Service:
Service:
Service:
Telephone: [phone]
Please retain for future reference.
Colours and contents may vary.
Waste electrical products should not be disposed of with household waste. Please recycle
where facilities exist. Check with your Local Authority or retailer for recycling advice.