7LED MODE 0 - 2 0 Sma t Sw led signalling mode:
0= leds always on acco ding to the elay state (ON = ed,
OFF = g een),
1= one single led flash to signal a elay state change:
(OFF->ON) = ed flash, (ON->OFF) = g een flash,
2 = g een led signal powe ON,
yellow (g een+ ed) led signal powe ON and elay ON;
8TX POWER 1 - 5 5 Cont ol unit RF t ansmission powe
(1=+2 dB, 2=+5 dB, 3=+8 dB, 4=+13 dB, 5=+20 dB).
9KEY POWER 1 - 3 3 Keyfob RF t ansmission powe
(1=+5 dB, 2=+10 dB, 3=+12 dB).
10 CHAN SEL MODE 0 - 2 0 Radio channel selection:
0= standa d channel,
1= channel selected f om “PROG CHANNEL” pa amete .
2= channel andomly selected between those available
11 PROG CHANNEL 1 - 30 30 P og ammed channel selection.
Used only if pa amete CHAN SEL MODE =1
12 CMD REPEAT 0 - 2 0 Command epetition without a eceived eply (0 = don't epeat)
13 ADDRESS BYTES 3 - 8 3 Add ess byte numbe
14 SECURITY BYTES 6 - 16 6 Secu ity byte numbe
15 KEY COPY ENABLE 0 - 2 1 Enabling of key-fob button cloning
0= disabled,
1= buttons can be cloned but “clones” a e not allowed to be cloned,
2= buttons can be cloned and also “clones” a e allowed to be cloned.
KEYFOB
The pocket sized key-fob has two buttons and th ee colo s (g een/ ed/yellow) signaling led.
Befo e being used it must fi st be egiste ed to it's “slave” olling shutte cont ol unit.
Regist ation p ocedu e att ibute to the single button a code to cont ol the “slave device”.
The p ocedu e the efo e, has to be epeated fo eve y button which we want to elate with a cont ol unit.
Keyfob registration procedure
To egiste a new key-fob sta t the app e push the “Start NFC Connection”, then put in contact you phone antenna with
the top su face of the cont ol unit whe e the NFC symbol is. Afte a few moments device data will appea on the sc een
togethe with buttons to access the gene al settings menu. To p oceed, push the “Device Registration” button and again
put in contact you phone with the NFC symbol on the sticke , now the cont ol unit LED begin to blink yellow fo a few
seconds allowing egist ation of a new keyfob button which is achieved by pushing the button fo about 3 seconds.
Regist ation is confi med by the keyfob with a se ies of 4 g een blinks. If the keyfob was p eviously egiste ed to
anothe Sma t Sw, it's necessa y to e ase the p evious egist ation, befo e attempting a new egist ation.
N.B. If when pushing the button it immediately emits a single yellow blink, it means that the button was al eady
egiste ed and to be egiste ed again, the p evious egist ation need to be e ased.
To do that you need to push the button fo about 10 seconds, until the g een LED sta t to blink, elease the button and
push it again fo about 10 seconds, until the ed LED blinks b iefly.
Button is e ased if when pushing it a yellow blink appea s afte about 3 seconds.
Keyfob button cancellation
To e ase a button, push it fo about 10 seconds, until the g een LED sta t to blink, elease the button and push it again
fo about 10 seconds, until the ed LED blinks b iefly.
Button is e ased if when pushing it a yellow blink appea s afte about 3 seconds.
Keyfob cloning procedure
If a button has been egiste ed with pa amete “KEY COPY ENABLE”=1, it is possible to clone that button to anothe
key-fob by p essing the button fo about 10 s until the key-fob yellow led sta ts to blink, keeping the button p essed,
now p ess the button that need to become a clone until it's elative g een led blinks b iefly confi ming the occu ed
cloning.
The button so obtained cannot be used to do othe cloning. If pushed fo about 10 seconds, the cloned button gene ate a
yellow led blink instead of a g een blink.
If the o iginal button has been egiste ed with pa amete “KEY COPY ENABLE”=2, then also its clones can be
themselves cloned.
