Lorex AX62TR Series User manual
Lorex Home Center Extender
AX62TR Series
Quick Start Guide
lorex.com
From all of us at Lorex, we welcome
you to our community – thanks for
your purchase of the Lorex Home
Center Extender. We designed this
product with you in mind, to extend the
performance and range of our new
Lorex Home Center. Here’s how to get
started.
Welcome!
What you’ll find in the box
USB Power PackLorex Home Center
Extender
Overview
Speaker USB power
port
Reset /
disable
alarm
button
LED
indicator
Placement of the Lorex Home Center Extender
• The ideal location to place the
extender/repeater is halfway
between your Lorex Home
Center and your other Lorex
device(s) that need better Wi-Fi.
• Look for a power outlet that’s
roughly halfway between your
Lorex Home Center and your
other Lorex device(s).
Based on factors such as the
distance between your devices, the
size of your home, environmental
conditions, physical obstructions,
and how much frequency
interference there is in your area,
here are some placement
recommendations for the
extender/repeater.
Find a central location.
Placement of the Lorex Home Center Extender
• Limit the amount of
walls, ceilings, and
other major obstructions
between the extender/
repeater and your other
Lorex device(s).
• Make sure that the outlet
that you choose has a
strong Wi-Fi signal from
your home router.
Device Setup
1. Plug the USB power cable into the extender/repeater. Then plug the power adapter into
a wall outlet to power on.
Note: The LED light will ash blue when ready to pair.
2. Unlock the Lorex Home Center and tap on Device Manager in the homescreen.
3. Go to the Repeater tab, then tap +on the top right to pair.
4. In the Device Setup screen, tap Repeater and tap Next.
5. Once your device has been detected, tap Next.
The Lorex Home Center will now display the extender/repeater on your homescreen.
Attention: Setup the Lorex Home Center before going through these steps.
Device Settings
You can view the extender/repeater’s device information or congure the settings for sound,
LED light status, and rmware updates, all through the Lorex Home Center.
To open the extender/repeater’s Device Settings:
1. Unlock your Lorex Home Center and tap the extender/repeater displayed on the
homescreen.
2. In the extender/repeater’s device screen, tap the three dots on the top for
settings.
Sound Settings
There are two audio options that can be enabled or disabled in the extender/repeater’s
sound settings.
1. Event Notication Chime: The extender/repeater will sound the event notication
chime when a camera has detected motion or a sensor has been triggered. The chime
is disabled by default.
2. Doorbell Chime: When someone rings the doorbell, the extender/repeater will sound
the doorbell chime. The chime is enabled by default.
Note: You must have a Lorex doorbell connected to the Lorex Home Center for this
option.
Light Status Indicators
See the table below for denitions of the extender/repeater’s LED light status indicators:
(off) • Powered off
• LED status is turned off
• Powered on
• Pairing successful
• Strong Wi-Fi signal strength
(ashing) Pairing with other devices
Resetting
(ashing) Disconnected from the Lorex Home Center
(ashing alternatively) Firmware update in progress
Weak Wi-Fi signal strength
(ashing) Alarm has been triggered
Troubleshooting
1. After installing the extender/repeater, I still have low signal strength on my camera(s).
Make sure that your faraway camera(s) are connected to the extender/repeater directly. To check
this, go to the Lorex Home Center’s Device Manager settings from the homescreen and see if your
camera(s) are still connected. If you’re nding that your camera(s) are still connected to the Lorex
Home Center and not to the extender/repeater, then you will need to do the following:
Your camera(s) should now automatically connect to the extender/repeater as long as the signal
from the extender/repeater is stronger than the signal from the Lorex Home Center. If you are still
having trouble, consider moving the extender/repeater closer to the camera(s).
2. The extender/repeater is showing low signal strength. How do I x this?
Go to the page “Placement of the Lorex Home Center Extender” on this quick start guide for
optimal placement recommendations.
3. How do I reset the extender/repeater?
Press and hold down the reset button on the back of the extender/repeater for about 10 seconds
until you hear the chime. The extender/repeater will then reset and the LED light status will ash
blue to indicate that it’s ready to pair to your Lorex Home Center.
1. Power off the camera(s) with low Wi-Fi signal strength.
2. Make sure the extender/repeater is powered on and connected to the Lorex Home Center.
3. Power the camera(s) back on.
For up-to-date information and support,
visit help.lorex.com/series/LHCE.
Lorex Home Center Extender
FCC NOTICE
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION.
Important:
• The Lorex Home Center Extender is rated for indoor use only. Do not use
outdoors.
• Only use with included power supply.
• A Lorex Home Center is required to operate the Lorex Home Center Extender.
Table of contents
Other Lorex Extender manuals
