Lorex QLR-0440 Series Service manual

for Dial-Up Connection of DVR
PPPoE(Point to Point Protocol over Ethernet)
Setting Guide Manual
(Rev. 2004.02.09)

CO TE TS
CO TE TSCO TE TS
CO TE TS
Setting for the DVR Server Computer
: <Incoming Connection Setting>
Case1. Windows 98, ME...............................................................................................................
Case2. Windows 2000..................................................................................................................
Case . Windows XP.....................................................................................................................
6
11
Setting for the DVR Client Computer
: <Dial-Up Connection Setting & How to Connect to the DVR Server>
Case1. Windows 98, ME...............................................................................................................
Case2. Windows 2000..................................................................................................................
Case . Windows XP.....................................................................................................................
16
20
25
Notice 1: How to know the User name registered in the DVR Server Computer...............
Notice 2: How to find out the IP address of the DVR Server Computer
at the Client................................................................................................................
0
1

Windows98,ME <Incoming Connection Setting> DVR Server
Computer
This Setting is to accept incoming connection from DVR Client, so apply only to the DVR
Server Computer
) On the Windows Desktop, select the ‘Start’ -> ‘Settings’ -> ‘Control Panel’.
2) Double-click the ‘Add/Remove Programs’.
3) Select ‘Windows Setup’ tap and check the ‘Communications’ component and click
‘Details’.

DVR Server
Computer
4) Check the ‘Dial-up Server’ component and click ‘OK’.
5) Then, on the Windows Desktop, select the ‘Start’ -> ‘Programs’ -> ‘Accessories’ ->
‘Communications’ -> ‘Dial-up Networking’.
6) Click the ‘Connections’-> ‘Dial-up Server’ in Menu, and then the ‘Dial-up Server’
window appears for ‘Incoming Connections’. Click ‘Next’.

DVR Server
Computer
7) Select the ‘Allow caller access’ (

).
Click ‘Change Password’ and register new password to allow caller access. Click ‘OK’.
8) Click ‘Server Type’ and confirm the type of Dial-Up Server. Click ‘OK’
9) Then you can confirm that the Status is changed ‘Idle’ to ‘Monitoring’. Click ‘OK’.
0) Then you can confirm that the Dial-Up Server Icon ( )
is created on the Task bar.

Windows2000 <Incoming Connection Setting> DVR Server
Computer
This Setting is to accept incoming connection from DVR Client, so apply only to the DVR
Server Computer.
) On the Windows Desktop, select the ‘Start’ -> ‘Programs’ -> ‘Accessories’ ->
‘Communications’ -> ‘Network and Dial-up Connections’.
2) Double–click the ‘Make New Connection’, and then the ‘Network Connection Wizard’
is
run for ‘Incoming Connections’. Click ‘Next’.

DVR Server
Computer
3) Select the ‘Accept incoming connections’ (

), and click ‘Next’.
4) Select the Devices for Incoming Connections (

), and click ‘Next’.
5) Select the ‘Do not allow virtual private connections’ (

), and click ‘Next’.

DVR Server
Computer
6) In this step, select the users allowed to connect to this computer. Only the allowed
users (Client) can connect to DVR Server system in this computer.
To add new user, click ‘Add’ and register new user’s name and password. Click ‘OK’.
Then you can confirm a new user registered.
Select the users allowed to connect to this computer(

), and click ‘Next’.

DVR Server
Computer
7) Select the ‘Internet Protocol [TCP/IP]’, and click ‘Properties’.
8) In this step, assign specified TCP/IP addresses for DVR system communications.
Check the ‘Allow callers to access my local area network’(

), and select the
‘Specify TCP/IP addresses’(

). Then, write [100.0.0.1] in From and [100.0.0.2] in To.
Click ‘OK’.
9) Windows has finished installing for Incoming Connection. Click ‘Finish’.

DVR Server
Computer
0) Then you can confirm the ‘Incoming Connection’ icon is created in ‘Network and
Dial-up Connection’