Louisiana Grills Black Label LG1200BL User manual

10640
10671
WOOD PELLET GRILL & SMOKER
GRIL ET FUMOIR À GRANULES DE BOIS
PARRILLA Y AHUMADOR DE
PELLETS DE MADERA
IMPORTANT: READ CAREFULLY, RETAIN FOR FUTURE REFERENCE.
MANUAL MUST BE READ BEFORE OPERATING!
IMPORTANT, PRENEZ CONNAISSANCE DE CE DOCUMENTET
CONSERVEZ-LE POUR RÉFÉRENCE ULTÉRIEURE VOUS DEVEZ
LIRE CE GUIDEAVANT D’UTILISER LE BARBECUE !
IMPORTANTE, LEER DETENIDAMENTE, CONSERVAR PARA
REFERENCIA FUTURA. LEA EL MANUALANTES DEL USO!
WARNING: FAILURETO FOLLOWTHESE INSTRUCTIONS COULD RESULT IN
PROPERTYDAMAGE, BODILYINJURY OR EVEN DEATH.CONTACT LOCAL
BUILDING OR FIRE OFFICIALSABOUT RESTRICTIONS AND INSTALLATION
INSPECTION REQUIREMENTS IN YOUR AREA.
AVERTISSEMENT: LE NON-RESPECTDE CES INSTRUCTIONS PEUT
ENTRAÎNER DES DOMMAGES MATÉRIELS,DES DOMMAGES CORPORELS
OU MÊME LAMORT. CONTACTEZ LESAUTORITÉS LOCALES COMPÉTENTES
CONCERNANTLES RESTRICTIONS ETLES EXIGENCES D’INSPECTION EN
VIGUEUR DANS VOTRE RÉGION.
ADVERTENCIA: SI NO SE SIGUEN ESTAS INSTRUCCIONES,PUEDEN
PRODUCIRSE DAÑOS MATERIALES,LESIONES CORPORALES O INCLUSO
LA MUERTE. PARACONSULTAR LAS RESTRICCIONES YREQUISITOS DE
INSPECCIÓN DE LAS INSTALACIONES DE SU ZONA, PÓNGASE EN CONTACTO
CON LOS ENCARGADOS DE EDIFICIO O EL DEPARTAMENTO DE BOMBEROS.
LG1200BL
ASSEMBLY GUIDE
GUIDE D'ASSEMBLAGE
GUÍA DE MONTAJE
300522
FOR OUTDOORAND HOUSEHOLD USE ONLY. NOTFOR COMMERCIAL USE.
RÉSERVÉ À L'USAGE EXTÉRIEUR ET RÉSIDENTIEL UNIQUEMENT. NON DESTINÉ À UN
USAGE COMMERCIAL.
SOLO PARA USO DOMÉSTICO Y EN EL EXTERIOR. NO APTO PARA USO COMERCIAL.

LOUISIANA GRILLS
2
ENGLISH
ENGLISH
COPYRIGHT NOTICE
Copyright 2020.All right reserved. No part
of this manual may be copied,transmitted,
transcribed, stored in a retrieval system,
in any form or by any means without
expressed written permission of,
DANSONS
3411 North 5th Avenue, Suite 500,
Phoenix, AZ, USA 85013
[e-mail]
[e-mail]
www.louisiana-grills.com
CUSTOMER SERVICE
Monday through Sunday,
4am - 8pm PST (EN/FR/ES)
Toll-Free: 1-877-303-3134
Fax: [phone]
ASSEMBLED (WxHxD) WEIGHT
1,464 x 1,172 x 823 mm /
57.6 x 46.1 x 32.4 in
95.7 kg /
210.9 lb
COOKING AREA TEMPERATURE RANGE
Upper - 2,722 cm² / 422.0 sq. in.
Lower - 4,894 cm² / 758.6 sq. in.
TOTAL - 7,616 cm² / 1,180.6 sq. in.
82-315°C /
180-600°F
LG1200BL
ELECTRIC REQUIREMENTS
110-120 V, 60 Hz, 375 W, 3-prong grounded plug
NOTE: Due to ongoing product development, parts are subject to change without notice. Contact
Customer Service if parts are missing when assembling the unit.
PART# DESCRIPTION
1 Upper Cooking Rack (x1)
2 Cooking Grids (x3)
3 Flame Broiler Slider (x1)
4 Flame Broiler Main Plate (x1)
5 Main Barrel / Hopper Assembly (x1)
6 Burn Grate (x1)
7 Meat Probe (x2)
8 Grease Bucket Liner (x1)
9 Grease Bucket (x1)
10 Flame Broiler Adjusting Bar Handle (x1)
11 Flame Broiler Adjusting Bar (x1)
12 Lid Handle Bezel (x2)
13 Lid Handle (x1)
14 Front Shelf (x1)
15 Front Shelf Bracket / Left (x1)
16 Front Shelf Bracket / Right (x1)
17 Bottom Shelf (x1)
18 Support Leg A (x2)
19 Support Leg B (x2)
20 Locking Caster Wheel (x4)
A Screw (x30)
B Screw (x2)
C Washer (x32)
DLocking Washer (x32)
E Screw (x2)
A B C D E
1
2
3
4
5
6
9
8
10 11
12
13
14
15 16
17
7
18
19
20

www.louisiana-grills.com
3
ENGLISH
ENGLISH
ASSEMBLY PREPARATION
MAJOR CAUSES OF APPLIANCE FIRES ARE A RESULT OF POOR MAINTENANCE AND A FAILURE TO MAINTAIN
REQUIRED CLEARANCE TO COMBUSTIBLE MATERIALS. IT IS OF UTMOST IMPORTANCE THAT THIS PRODUCT BE
USED ONLY INACCORDANCEWITHTHE FOLLOWING INSTRUCTIONS.
Parts are located throughout the shipping carton,including below the grill. Inspect the grill, parts, and hardware blister pack after removing from the
protective shipping carton. Discard all packaging materials from inside and outside of the grill before assembly, then review and inspect all parts by
referencing the parts list. If any part is missing or damaged, do not attempt to assemble. Shipping damage is not covered under warranty. Contact
Customer Service for parts: Monday through Sunday, 4 a.m. - 8 p.m. PST (EN/FR/ES).
WWW.LOUISIANAGRILLS.COM | TOLLFREE: 1.877.303.3134
IMPORTANT: TO EASE INSTALLATION, USING TWO PEOPLE IS HELPFUL (BUT NOT NECESSARY) WHEN ASSEMBLING THIS UNIT.
Tools required for assembly: screwdriver. Tool not included.
ASSEMBLING THE CART
PARTS REQUIRED:
1 x Bottom Shelf (#17)
2 x Support Leg A (#18)
2 x Support Leg B (#19)
8 x Screw (#A)
8 x Washer (#C)
8 x Locking Washer (#D)
INSTALLATION:
• Place a piece of cardboard on the oor to prevent scratching the unit and
parts.To ease installation, turn the bottom shelf upside-down (at side down).
• Prepare the four Support Legs for installation, arranging the labelled legs as
shown in illustration. Mount one Support Leg to the Bottom Shelf using two
Washers, Locking Washers, and Screws.
• Repeat the same installation for the remaining three Support Legs into the
Bottom Shelf.
ASSEMBLY INSTRUCTIONS
IMPORTANT: ITISADVISEDTO READ EACH STEP ENTIRELYBEFORE STARTINGASSEMBLY ON INSTRUCTIONS.DO
NOT TIGHTEN SCREWS COMPLETELY UNTIL ALL SCREWS FOR THAT STEP HAVE BEEN INSTALLED. HARDWARE
COMBINATION INVOLVING A LOCKING WASHER AND WASHER SHOULD BE INSTALLED WITH THE LOCKING
WASHER CLOSESTTOTHE HEAD OFTHE SCREW.
A
8x
CD
8x 8x
A
CD
1.ASSEMBLING THE CART
1 x Bottom Shelf (#2)
2 x Support Leg (#3)
2 x Support Leg (#4)
8 x
1/4-20x5/8" Screw (#A)
8 x
1/4 washer (#C)
8 x
1/4 spring washer (#D)
Place a piece of cardboard on the floor to prevent scratching the unit and parts. To ease
installation, turn the bottom shelf upside-down (flat side down). Prepare the four support legs
for installation, arranging the labelled legs as shown in illustration.
Mount one support leg to the Bottom Shelf using two screws,two washer,two
spring washer. Repeat installation for the other three support legs.
1
19
17
18
18
19

LOUISIANA GRILLS
4
ENGLISH
ENGLISH
ADDING WHEELS TO THE CART
PARTS REQUIRED:
4 x Locking Caster Wheel (#20)
INSTALLATION:
• Insert each Locking Caster Wheel into the bottom of each Support Leg by
hand-tightening into the hole. Ensure that each Locking Caster Wheel is
inserted completely so that the cart sits level on the ground. Lock each Caster
Wheel.
MOUNTING THE CART TO THE BARREL
PARTS REQUIRED:
1 x Main Barrel (#5)
16 x Screw (#A)
16 x Washer (#C)
16 x Locking Washer (#D)
INSTALLATION:
• Insert the assembled cart into the Main Barrel brace.Secure each Support Leg
to the brace using four Washers, Locking Washers and Screws.
TIP: USING A LOW TABLE IS USEFUL FOR THIS INSTALLATION STEP.
• Repeat the same installation of the other three Support Legs to the Main
Barrel brace.
TIP: TO EASE INSTALLATION OF THE FINAL SIDE, CAREFULLY TURN THE UNIT
TO LIE ON ITS BACK TO SECURE THE LAST FOUR SCREWS TO THE MAIN BARREL
BRACE.
• Once the cart is secure, carefully lift the grill into an upright position.
INSTALLING THE FRONT SHELF BRACKETS
PARTS REQUIRED:
1 x Front Shelf Bracket / Left (#15)
1 x Front Shelf Bracket / Right (#16)
6 x Screw (#A)
6 x Washer (#C)
6 x Locking Washer (#D)
INSTALLATION:
• Install one Front Shelf Bracket to the front of the Main Barrel by using three
Washers,LockingWashers and Screws.Note illustration for proper positioning.
• Repeat the same installation for the other Front Shelf Bracket.
2.MOUNTING THE WHEELS TO THE CART
4 x Locking Caster Wheel (#5)
Insert each locking caster wheel into the bottom of each support leg by hand-tightening into
the hole. Ensure the locking caster wheel is inserted completely.
A
16x
CD
16x 16x
A
D
C
3.INSTALLING THE CART TO THE BARREL
1 x Main Barrel (#1)
16x
1/4-20x5/8" Screw (#A)
16x
1/4 washer (#C)
16x
1/4 spring washer (#D)
Find a low table and place cardboard on it. Lay the main barrel on its side, hopper end pointed
upward, on the prepared low table. Note illustration.
Insert the assembled cart into the main barrel brace, and secure each leg to the brace using
four washers,
spring washer and screws. Repeat same installation for the other three
support legs. Note illustration To ease installation of the final side, carefully turn the grill to lie
on its back to secure the last four screws to the main barrel brace.
A
A
6x
CD
6x 6x
CD
4.INSTALLING THE FRONT SHELF BRACKETS
1x Front Shelf Bracket /L (#6)
6x Front Shelf Bracket /R (#7)
6x
1/4-20x5/8" Screw (#A)
6x
1/4 washer (#C)
6x
1/4 spring washer (#D)
Attach one front shelf bracket to the front of the grill barrel by using three screws.
Install each screw half-way , then tighten completely when all three screws are mounted and
aligned properly.
Repeat the same installation for the other front shelf bracket.
2
3
4
20
20
20 20
5
16
15

www.louisiana-grills.com
5
ENGLISH
ENGLISH
E
2x
CD
2x 2x
E
C
D
6.ATTACHING THE LID HANDLE
1x Lid Handle (#10)
2x Lid Handle Bezel (#9)
2x
1/4-20x3/4"
Screw (#E)
2x
1/4
washer
(#C)
2x
1/4
spring washer
(#D)
From inside the barrel lid, insert one screw so that it protrudes to the outside.
Add a bezel on the screw, then hand-tighten the screw (from the inside) into
7.POSITIONING THE BURN GRATE
1x Burn Grate (#11)
Proper placement and maintenance of the burn grate is vital to the use of the unit. Insert the
burn grate into the burn pot. The hole in the burn grate should align and be open for the igniter
to light the pellets. To verify proper positioning, ensure the curved lip of the burn grate is flush
with the top of the burn pot, and the notched side should sit flush, under the fuel deflector.
7.POSITIONING THE BURN GRATE
1x Burn Grate (#11)
Proper placement and maintenance of the burn grate is vital to the use of the unit. Insert the
burn grate into the burn pot. The hole in the burn grate should align and be open for the igniter
to light the pellets. To verify proper positioning, ensure the curved lip of the burn grate is flush
with the top of the burn pot, and the notched side should sit flush, under the fuel deflector.
6
2x
B
B
5.INSTALLING THE FRONT SHELF BRACKETS
1x Front Shelf (#8)
2x Screw (#B)
From underneath, insert the screw (from the outside) into the front shelf bracket and the front
shelf.
Repeat the installation for the other side of the front shelf.
2x
B
B
5.INSTALLING THE FRONT SHELF BRACKETS
1x Front Shelf (#8)
2x Screw (#B)
From underneath, insert the screw (from the outside) into the front shelf bracket and the front
shelf.
Repeat the installation for the other side of the front shelf.
INSTALLING THE FRONT SHELF
PARTS REQUIRED:
1 x Front Shelf (#14)
2 x Screw (#B)
INSTALLATION:
• From underneath, insert the Screw (from the inside) to fasten the Front Shelf
Brackets and the Front Shelf together. Note illustration 5A.
• When the Front Shelf is not in use, it can be lowered. Note illustration 5B.
INSTALLING THE LID HANDLE
PARTS REQUIRED:
2 x Lid Handle Bezel (#12)
1 x Lid Handle (#13)
2 x Washer (#C)
2 x Locking Washer (#D)
2 x Screw (#E)
INSTALLATION:
• Take one screw, add a locking washer and a washer, then from inside the Main
Barrel lid, protrude the screw to the outside. Add a bezel on the screw, then
hand-tighten the screw (from the inside) into the Lid Handle.
NOTE: DO NOT OVER-TIGHTEN THE SCREWS. ONLY A SNUG FIT IS NECESSARY.
• Repeat the same installation for the other end of the Lid Handle.
INSTALLING THE BURN GRATE
PARTS REQUIRED:
1 x Burn Grate (#6)
INSTALLATION:
• Insert the burn grate into the burn pot. The hole in the burn grate should align
and be open for the igniter to light the pellets. To verify proper positioning,
ensure the curved lip of the burn grate is ush with the top of the burn pot, and
the notched side should be ush under the fuel deector.
IMPORTANT: PROPER PLACEMENT AND MAINTENANCE OF THE BURN GRATE IS
VITAL TO THE USE OF THE UNIT.
5B
7A
7B
5A
6
12
12
13
14