Louroe HD-10 User manual

Model HD-10 Accommodates up to Ten Headphones
1/4” (6.3mm)
1/8” (3.5mm)
MOUNTING HOLES (2)
HEADPHONE JACKS
(TOTAL 10)
VOLUME CONTROLS
CORD LENGTH
APPROX 4FT (1.2mm)
Connecting the HD-10 to a Louroe Audio Base
Station
Connect the HD-10 into the headphone jack located
on front panel of the Louroe Base Station, using
1/8”(3.5mm) plug from HD-10.
Determining Audio Source Capacity
All audio sources have an output load
capacity, called output impedance. This
output impedance is specified using the term
“ohms”, which is often represented by the
symbol “?”. Headphones are also rated in
ohms, and when connecting a headphone to
an amplifier, it is important that the ohms
rating of the headphone should be equal to
or greater than the ohms rating of the
amplifier. For example, if the amplifier is
rated for eight ohms, the headphone should
be at least eight ohms.
Headphone impedance is dramatically
reduced when connecting multiple
headphones. Therefore, it is necessary to
use the following formula to determine the
combination impedance of several
headphones.
combined headphone impedance =
combined headphone impedance =
impedance per headphone
300 ohms per headphone
number of headphones being connected
10 headphones = 30 ohms
Example: Find the combined impedance of ten
300-ohm headphones
The audio source must have an impedance of
30ohms or less.
Note: This formula works when all
headphones are of the same
impedance. It is recommended that all
headphones be of the same type and
impedance to insure uniform output
volume for all listeners.
HD-10
HEADPHONE DISTRIBUTOR
INSTALLATION AND OPERATING INSTRUCTIONS
6955 VALJEAN AVE, VAN NUYS, CA 91406
PH: [phone] / FAX: [phone]
/ www.louroe.com[email protected]
®
Page 1
LOUROE ELECTRONICS 6955 VALJEAN AVENUE, VAN NUYS, CA 91406 TEL [phone] FAX [phone]
website: www.louroe.com e-mail: [email protected]
(818)
®
hd_10_inst_5/14

IMPORTANT NOTICE
When this equipment is used as part of an
audio monitoring system, the law requires
that the public be given notice of AUDIO
MONITORING ON THE PREMISES. A
decal notice is included with each
microphone shipped.
Federal Law References:
Federal Regulations, US Code, Title 18.
Crime and Criminal Procedure, Sec 2510.
HEADPHONE CONNECTION TO MODEL HD-10 HEADPHONE
DISTRIBUTOR AND TO A LOUROE AUDIO BASE STATION
HD-10
Headphone Distributor
4’ Cord Length
3.5mm Plug
¼” Plug
Remote microphone
connection
LOUROE
HP-15135
HEADPHONE
LOUROE
HP-15135
HEADPHONE
Louroe APR-1
Base Station
APR-1
FILTER
VCR
2-8HRS
12-24HRS
VCRIN
OVERLOAD
SINGLE ZONE AUDIO BASESTATION
OFF MAX
POWER-VOLUME
E
LOUROE
LECTRONICS
A Typical Louroe Audio Monitoring System Utilizing
Model HD-10 Headphone Distributor with Headphones
(HD-10 Supplied by Louroe)
INSTALLATION AND OPERATING INSTRUCTIONS
IMPORTANT NOTE
Make certain that ¼”
headphone plug is completely
inserted into HD-10 port
hd_10_inst_5/14
Page 2
LOUROE ELECTRONICS 6955 VALJEAN AVENUE, VAN NUYS, CA 91406 TEL [phone] FAX [phone]
website: www.louroe.com e-mail: [email protected]
(818)
AUDIO
MONITORING
On
These Premises
®
WARRANTY
LOUROE ELECTRONICS warrants that at the time of shipment products manufactured by LOUROE ELECTRONICS to be free of defects in material and workmanship.
Should a defect appear within one year (12 months) from date of shipment, LOUROE ELECTRONICS will, at its sole discretion, repair or replace the defective equipment.
This equipment shall not be accepted for repair or return without prior notification by LOUROE ELECTRONICS .
This warranty does not extend to any Louroe product that has been subjected to improper or incorrect installation, misuse, accident, or in violation of installation
instructions provided by LOUROE ELECTRONICS.
Returned shipments to LOUROE ELECTRONICS shall be at customer’s expense. LOUROE ELECTRONICS will return the equipment prepaid via best way.
®
®
®
®
®
®