Lowrance MapCreate 6 User manual

Pub. 988-0147-383
www.lei-extras.com
MapCreate 6
Custom Mapping Software for GPS
Installation and Operation
Instructions


Copyright © 2004 LEI. All rights reserved.
No part of this manual may be copied, reproduced, republished,
transmitted, distributed, downloaded or stored in any storage medium,
for any purpose, without prior written consent of LEI. Any
unauthorized commercial distribution of this manual is strictly
prohibited.
MapCreateis a trademark of LEI.
U.S. Points of Interest Data in this unit are by infoUSA,
copyright 2001-2004, All Rights Reserved. infoUSA is a
trademark of infoUSA, Inc.
U.S. eXitSource Database, copyright 2001-2003 Zenrin Co.
Ltd. Exit Authorityand eXitSourceare trademarks of
Zenrin Co. Ltd.
Canadian mapping data 2003 by DMTI Spatial Inc.
European mapping data 2003 by Tele Atlas NV,
the reference in digital mapping.
LEI Extras, Lowrance Electronics, or Eagle Electronics may find it
necessary to change or end their policies, regulations and special offers
at any time. They reserve the right to do so without notice. All screens
in this manual are simulated.
For free owner's manuals and the most current information on this
product, it's operation and accessories, visit the manufacturer's web
sites:
www.lowrance.com www.eaglegps.com
To purchase Lowrance or Eagle accessories,
visit our web site:
www.lei-extras.com
LEI
PO BOX 129
Catoosa, OK USA 74015
Printed in USA.

i
Table of Contents
Sec. 1: Introduction................................................................... I
Quick Start Reference ................................................................... 2
How MapCreate Works: The Basics ............................................ 6
File Formats & Functions ............................................................ 7
Map Border File ........................................................................ 7
Custom Map File....................................................................... 7
Important Notes: File Encryption and Card Limits................ 8
Important Notes About Cards and File Size ........................... 9
GPS Data File ......................................................................... 11
ASCII Text File ....................................................................... 11
GPS Data Manager (GDM) File ............................................. 12
Atlas File ................................................................................. 12
GPS Unit Compatibility ......................................................... 13
Mapping Detail: There's More Here Than Meets the Eye. ......... 13
Find Highway Exit Services ................................................... 13
Find Points of Interest............................................................ 14
Find an Address ...................................................................... 14
How to Use this Manual: Typographical Conventions.............. 15
Sec. 2: Installing MapCreate 6.3 ........................................... 17
System Requirements............................................................. 17
Installation Types ................................................................... 17
Installing MapCreate.............................................................. 18
Care of your MapCreate CDs ................................................. 28
Starting MapCreate ................................................................ 28
Sec. 3: User's Guide ................................................................. 31
Starting MapCreate.................................................................... 31
The MapCreate Screen ............................................................... 32
Closing MapCreate ................................................................. 33
MapCreate Screen Components ............................................. 33
Master Map Window............................................................... 34
Main Menu .............................................................................. 35
Toolbars ................................................................................... 35
Create Map (Easy) Toolbar................................................. 36
Create Map (Advanced) Toolbar......................................... 37
File Toolbar ......................................................................... 37
GPS Data Toolbar ............................................................... 38
Map Navigation Toolbar ..................................................... 39
Map Category Options Window ............................................. 40
Waypoint List Window ........................................................... 41
Icon List Window .................................................................... 41
Route List Window.................................................................. 42
Route Waypoint List Window................................................. 42

ii
Trail List Window ................................................................... 43
Moving around the Master Map................................................. 44
Pan Arrows.............................................................................. 44
Center Map.............................................................................. 44
Zoom Area ............................................................................... 45
Zoom in/Zoom Out................................................................... 45
Zoom Range Window .............................................................. 46
Creating Rectangle Map Borders............................................... 47
Estimate Map Size (Optional) ................................................ 48
Saving a Map Border File (Optional)..................................... 48
Creating Corridor Map Borders ................................................. 50
Edit Corridor Borders ............................................................. 52
Creating and Saving a Custom Map.......................................... 52
Creating a Waypoint................................................................... 54
Creating an Icon ......................................................................... 56
Creating a Route......................................................................... 58
Saving a GPS Data File.............................................................. 61
Moving GPS Data Files Between Computer and Unit.......... 62
Creating a Corridor Map from a Route...................................... 63
Creating a Route from a Trail .................................................... 66
Appendix 1: MapCreate Command List.............................. 69
Searching Help............................................................................ 70
Appendix 2: Map Category List............................................ 73
Appendix 3: MapCreate 6 Symbol Key................................ 77
Appendix 4: Displaying Specialty Maps ............................. 81
IMS Fishing Hot Spots Maps ..................................................... 82
Jeppesen Aviation Maps............................................................. 83
Appendix 5: Planning Highway Routes.............................. 87
Tips on Making Better Routes for Highway Navigation....... 87
"High Resolution" vs. "Low Resolution" Routes .................... 87
Index........................................................................................... 91
LEI End User License Agreement ....................................... 95

iii
Notes

iv
WARNING!
A CAREFUL NAVIGATOR NEVER RELIES ON ONLY ONE METHOD
TO OBTAIN POSITION INFORMATION.
CAUTION
When showing navigation data to a position (waypoint), a GPS unit will show
the shortest, most direct path to the waypoint. It provides navigation data to the
waypoint regardless of obstructions. Therefore, the prudent navigator will not
only take advantage of all available navigation tools when traveling to a way-
point, but will also visually check to make sure a clear, safe path to the waypoint
is always available.
WARNING!
When a GPS unit is used in a vehicle, the vehicle operator is solely re-
sponsible for operating the vehicle in a safe manner. Vehicle operators
must maintain full surveillance of all pertinent driving, boating or fly-
ing conditions at all times. An accident or collision resulting in damage
to property, personal injury or death could occur if the operator of a
GPS-equipped vehicle fails to pay full attention to travel conditions and
vehicle operation while the vehicle is in motion.

1
Section 1: Introduction
How this manual can get you into the field, fast!
Thanks for buying MapCreate, the custom mapping software for
Lowrance and Eagle GPS units. This manual was written using Map-
CreateU.S.A. and MapCreateCanada versions 6.3. Beginning with
version 6.3, all MapCreate packages work identically, but contain dif-
ferent mapping data.
We know you're eager to install the program and make some maps, but
we have a favor to ask. Before you grab that CD, give us a moment to
explain how our manual can help you get the best performance from
our software. Our goal is to get you on the road, into the air, or out to
the woods and water fast. Like you, we'd rather spend more time out-
doors, and less time reading a manual!
That's why we designed this book so you don't have to read the whole
thing from front to back for the information you want. You can skip
around! If you know where to look, we've made it easy to find the tips
you may need from time to time.
The manual has three main sections:
Section 1: Introduction contains the Quick Start Reference, which
begins on page 2. We put it near the front of the book so you can turn to
it quickly. Sec. 1 also includes background information on how Map-
Create and its file formats work. To understand how to interpret our
instruction text, be sure to see the Typographical Conventions seg-
ment on page 15. Don't miss the important notes on File Encryption
and Card Limits on page 8.
Section 2: Installing MapCreate (on page 17) will help you get the program
and the required LEI card reader correctly installed on your computer.
Section 3: User's Guide (on page 31) is the heart of our book. It intro-
duces you to the MapCreate windows and toolbars. Sec. 3 contains
easy-to-skim lessons on the program's main operations. These segments
show you how to make highly customized maps and GPS information
and get them into your GPS unit.
After you've gained some experience with the program, you may want
to try some advanced features. That brings us to the Command Refer-
ence, which is available only in the MapCreate 6 Help file. It contains
— in alphabetical order — the more advanced command functions in
MapCreate.
Each entry includes a summary box briefly telling what the command
does and how to run it from the menu, toolbar or keyboard. Then, we've

2
included more tips and tricks so you can take advantage of all the
power and performance MapCreate offers.
You can see an example of the Help file's Command Reference format in
Appendix 1 at the back of this manual, on page 69. Appendix 1 contains
the entry on the Help Command, which explains how to use Help.
In addition to the Command Reference, the Help file includes material
from this manual's User's Guide segment. Just press the F1 key to
launch Help. You can find facts fast by electronically searching the
Help File for the word or phrase you want.
In our printed manual, we've included other general supplemental ma-
terial as appendices in the back of the book. Check out the Table of
Contents to see the topics contained in each appendix.
After you have the software and card reader installed, browse through
the tutorials in Sec. 3 to get you going. Later, when you want to try
something new or you have a question about a particular function, skim
through the manual's table of contents or search the Help file's Command
Reference to read what you need.
If you're an experienced computer user, you can probably install Map-
Create and the card reader without the manual. But, if you need a little
coaching, jump ahead to Sec. 2 and we'll walk you through the install
step by step. (If that's not easy enough, just grab the nearest teenager
and ask him or her to install it for you!)
If you've skipped ahead and already have MapCreate installed, check
out the Quick Start Reference below. If you're the type of person who
wants more background information before you start, turn to How Map
Create Works on page 6, or begin learning about the MapCreate screen
components at the start of Sec. 3.
Quick Start Reference
This 13-step summary will get you started with a simple map. It as-
sumes you have already made a full, default installation of the program,
and one of the CDs is in your CD-ROM drive. (Complete installation in-
structions begin in Sec. 2.) For more detailed explanations, read through
the lessons in Sec. 3. Before you start, make sure your LEI MMC card
reader is installed and working, and you know the reader's drive letter.
Many toolbar buttons are labeled, and an informative tool tip box pops up
when you point to a button.
How to make and save a rectangle map
1. Start MapCreate by clicking the Windows START button and choosing
your version of MAPCREATE from the menu.
2. Maneuver the Master Map so you can see the area you want to in-

3
clude in your map. Use the PAN ARROW buttons to move north, south,
east or west. Use the ZOOM-INand ZOOM-OUT (Z-INor Z-OUT) buttons as
needed to close in on or back away from the area you're viewing.
3. Click the DRAW MAP BORDERS button in the toolbar. Move the mouse
pointer above and to the left of the desired area. Click, hold down the
mouse button and drag diagonally down and to the right until the de-
sired area is enclosed with the green border box. Then release the
mouse button. You have just drawn a Map Border.
4. With the Map Border displayed, click the ESTIMATE CUSTOM MAP SIZE but-
ton, on the Create Map toolbar. After a moment it will tell you your map's
file size. If it fits the card, click OKto clear the message and jump to step 5.
If the map file is too large for the card, click OKto clear the message, then
redraw your map border a little smaller. Click the DELETE MAP BORDER but-
ton, click on any green border line, then re-draw a smaller border box. Use
the Estimate button to re-check the size until it is correct.
Click the OK button to clear the message box from your screen.
5. When your file is the right size, click the CREATE MAP button on the
Create Map toolbar. The program displays a message about copyright
and encryption.
6. If this is the first time you have tried to save a file to your memory
card, MapCreate will need to register the card. Make sure you have a
card in your card reader. Click OKto continue. (Clicking Cancel ends
the process.) If you have already registered the card you are using, click
OKand skip to step 11.
Read the message, and then click OK to continue.

4
7. Another message box asks whether you want to register your current
card or not. Click YES to continue the card registration process.
Click Yes to register your current memory card with MapCreate.
8. You can change the label on your memory card if you prefer. Delete
the default name, "Card1," and enter the new name. Click
REGISTER to continue.
Delete the default label, if you prefer, and enter a new name. Then
click Register to continue.
9. Another message box tells you when your card has been registered.
Click OKto continue.
Click OK to continue the create map process.
10. The Card Registry window appears again. Click DONE to save your
map.

5
Click Done to complete the registry process.
NOTE:
If the AUTOMATICALLY APPEND LABEL TO SAVED MAPS box is selected (see
figure above), MapCreate will automatically add your card's label to
the end of whatever name you give the file you are saving. Let's use
the figure above as an example. If we name our map "Phoenix.lcm,"
MapCreate will automatically name the file "Phoenix_CARD1.lcm."
To cancel this option, click the Automatically Append… box to re-
move the check mark.
11. A window shows the progress of your map build. When the map is
built, MapCreate displays the SAVE ASdialog box. Type a file name for
your Map File, and click SAVE. (MapCreate will save your new custom
map to your memory card.)
12. After the program has saved the map to your card, the Save Prog-
ress box disappears. You can now close MapCreate and remove the card
from the reader.
13. Follow the instructions in your GPS manual for loading the MMC or
SD card into your unit. It will automatically read the map when the
unit is turned on.
NOTE:
Custom maps and GPS data (waypoints, routes, trails, icons) are
contained in two different file types. We describe their functions in
the following segments on how the program works.

6
How MapCreate Works: the Basics
You'll be making maps faster if you understand the hoops MapCreate
must jump through to cram a high-detail map into your GPS unit.
First of all, those CDs you just purchased contain a whole bunch of raw
digital cartography data. There are several hundred files of digital map-
ping information containing lake shorelines, navigation aids, roads, riv-
ers and all the other information that goes into our high-detail maps.
It takes some fancy formatting to fit the whole world onto a few com-
pact discs. Your GPS unit can't read those raw files (called atlas files).
Even if it could, no GPS unit or MultiMedia Card (MMC) has enough
memory to hold that much information.
This is where MapCreate comes in. The program looks at all those raw
atlas files, shuffles the different types of information together, and then
places them onto your computer screen. That's what we call the Master
Map, the main window in the MapCreate interface. By changing vari-
ous options in MapCreate, you can control how much geographic detail
is displayed on-screen in the Master Map.
It's a pretty cool electronic map, but your GPS can't read it in this form,
either. This is where you come in. You move around the Master Map
and locate the area or areas you want to make a detailed map of. Then,
you grab the computer mouse and draw a map border around the re-
gion you want. (There are two or three fun ways to do this…we'll de-
scribe 'em in a few minutes.)
Now, this map border isn't really a map yet — it just defines or outlines
the area you want to include in the final GPS-friendly map. If you wish,
you can save the boundary you have drawn as a Map Border File.
MapCreate uses a map border like an electronic shopping list. The pro-
gram looks at your border, grabs the appropriate raw atlas information,
and then glues it all together as a custom map. Now you can save this
data as a Custom Map File on an MMC (or SD card) and load it into
your GPS unit. (If you like, you can backup the Map File by copying it
from the MMC card to your computer's hard drive.)
GPS information — such as waypoints, routes or trails — is handled
differently. You can click the mouse to set a waypoint or plan a route,
then save that information as a GPS Data File. Just save it directly
on or copy it to the MMC and this file is ready to load into your GPS
unit. When your unit makes trails or waypoints in the field, that infor-
mation is also saved as a GPS Data File. Your GPS unit can save the
file to the MMC, which allows you to copy the GPS Data File back into
your computer. Then you can open, edit and save it in MapCreate.

7
File Formats & Functions
Well, now you know what makes MapCreate tick. You may be ready to
skip forward to where we explain how our text formatting makes the
manual easy to skim. If that's the case, move on to "How to Use This
Manual: Typographical Conventions" on page 15. But, if you want to
pick up an extra tip or two, look over this segment describing the file
formats and memory cards MapCreate works with.
Map Border File
This file defines the boundary of the raw cartography data that is ex-
tracted and converted to a GPS custom map, or Map File. The border
file information is displayed on the computer's Master Map screen as
either a green rectangle (rectangle map border) or a magenta polygon
shape (corridor map border.) The file extension is *.lmp.
In MapCreate 6.3, you can draw a border, then build and save a map
without saving the border. However, some MapCreate power users still
like to save their borders as Map Border Files. That lets them make
changes to a border or even combine different borders without drawing
them from scratch each time. By default, MapCreate will first save a
Map Border File to the C:\Program Files\LEI\MapCreate\Data folder,
but if you prefer you can save it on your memory card. If you save else-
where, MapCreate remembers that location the next time you save. Ver-
sion 6.3 also stores map border information in each Map File. This lets
you generate a border simply by opening an existing Map File, includ-
ing maps built by previous versions of MapCreate 6.
A Map Border File can contain one or more different map border sets,
and these border sets don't need to be next to each other on the map.
For example, you can draw a rectangle border around one lake and
then draw a second corridor border around another lake several miles
away, and include both of those border sets into one Map Border File.
There is no limit (other than space on your hard disk, MMC or SD card)
on how many different border sets you can include in a Map Border
File. You can open and edit a Map Border File and then save the file
with the changes you made.
Custom Map File
This is the actual map format used by your GPS unit. MapCreate takes
the borders you drew (or saved as a Map Border File), extracts that
area's information from the raw atlas data, then converts it to a Cus-
tom Map File, often called a Map File for short. We call this conversion
process "creating the map." The file extension is *.lcm.
By default, MapCreate will first save a Map File direct to your MMC memory
card. If you prefer, you can save a Map File on your computer hard drive. When

8
hard drive space is available, many users like to archive Map Files in the
C:\Program Files\LEI\MapCreate\Data folder. This allows you to change
maps on your card and reuse a map over and over without creating it each time.
If you save a map to the Data folder, MapCreate will remember that location the
next time you save a map, during the current work session. The next time you
start MapCreate, map saves will default back to the MMC card.
You cannot make changes to a Map File once it has been created. If you
want to make changes to a map, return to its original companion Map
Border File or retrieve the map borders by opening the Map File
(*.lcm). Make your changes to the border, then create a fresh Map File.
You can delete the old one, or just save the new map over the old map.
Important Notes: File Encryption and Card Limits
We collect and purchase cartography data from several sources. Much
of this data is copyrighted, and our data suppliers require that we pro-
tect our maps from illegal copying. One level of protection requires that
you have a MapCreate CD in the disc drive each time you launch the
program. We also encrypt Map Files, and limit the number of MMC or
SD cards you can use to store maps.
Map File Encryption
All maps built by MapCreate are required to be encrypted (or locked) to
a specific memory card. This encryption process must be done on maps
saved both to a memory card and your hard drive. Once a map has been
encrypted to a specific memory card, you can make a backup copy on
your hard drive, but you cannot copy the map to a different card. (Well,
you can copy it to another card, but your GPS unit won't recognize it.
To work, the Map File must reside on the card it was encrypted to.)
Limited Number of Cards
All MapCreate users are limited to saving maps on a maximum of five
different memory cards. MapCreate tracks the number and identity of
your cards by "registering" each card with the program. The software
needed to register cards will not work with third-party card readers, so
MapCreate will only work with the card reader from LEI. Once you
have registered a card, it can never be unregistered and its place ex-
changed with another card.
Since you are limited to five, we strongly recommend that before you
buy more cards, you should give some thought to the type of travel you
do and your map size requirements. Memory cards come in several dif-
ferent sizes, so you need to think ahead and match card capacity to the
type of maps you will need.

9
To help you decide what size cards to buy, make some map borders cov-
ering the type of travel you expect. Then use the Estimate Custom Map
Size command to calculate the size.
For example, one Missouri customer frequently travels and fishes in
the four-state area of Kansas, Missouri, Arkansas and Oklahoma. He
purchased an additional 128MB MMC, which holds all four states at
once. This lets him travel long distances for extended periods without
needing a computer to change the maps on his card.
To give you an idea of how big a Map File can be, we made some exam-
ples using the regular versions (no topographic data) of MapCreate
USA and MapCreate Canada, with all mapping categories included.
(Size will vary depending on which package of MapCreate you have.)
In the U.S., Lake Michigan is approximately 26 MB, all of Missouri is
41 MB and the entire state of California is approximately 87 MB. A six-
mile-wide corridor map from San Diego, California to the Maine-
Canada border, following Interstate highways, is about 50 MB.
In Canada, a map of Lake Winnipeg (including the major lakes to the
northwest) is 6.84 MB. All of Saskatchewan is 64 MB, all of British
Columbia is 69 MB. A six-mile-wide corridor map from Prince Rupert
on the west coast to Louisbourg on the east coast, following Trans-
Canada highways, is about 35 MB.
Important Notes About Cards and File Size
The size of a Map File is important. It must be small enough to fit on
the MMC (MultiMedia Card) that your GPS uses for data storage. This
solid-state, flash memory device is about the size of a postage stamp.
(SD [Secure Digital] cards are also compatible with any Lowrance or Ea-
gle product that uses MMCs.)
At press time, the MMCs shipped with the GPS Accessories Pack ver-
sion of MapCreate 6.3 are 32 MB size. If you're using a 32 MB MMC,
your Map File must be less than 32 MB in order to fit on the card. (This
space issue is the same as floppy disks; you can't really fit a 1.44 MB
file onto a 1.44 MB diskette because some space is required for the
disk's file allocation table. In the case of a 32 MB MMC, actual maxi-
mum useable space will be approximately 29 MB to 30 MB.)
MMCs and SD cards are used in a variety of other digital devices. Most
electronics or digital camera stores sell MMCs and SD cards, and at
press time they are available in 16 MB, 32 MB, 64 MB, 128 MB, 256
MB and 512 MB sizes. Cards with even greater capacity will likely be
available in the future. MapCreate is a powerful tool for your GPS, be-

10
cause it allows you to match your map's file size and detail level to your
card's memory capacity and your travel needs.
NOTE:
Due to software requirements in the GPS units, MMC or SD cards
can hold a maximum of 32 different files at one time for the
Lowrance iFINDERand 1,000 different files for all other
Lowrance or Eagle GPS receivers. The total amount of information
cannot exceed the MMC size capacity, no matter what the number
of files is. For example, an 8 MB MMC in an iFINDER could hold
approximately one 7.66 MB file, or 32 files, so long as the 32 files
totaled 7.66 MB or less.
Other brands of GPS units use direct serial cable connections to trans-
fer high detail maps from a computer to the GPS device. Lowrance and
Eagle switched from this traditional method to removable memory
cards for several reasons. A USB card reader can transfer a large cus-
tom map to your unit 30 times faster than a serial cable connection.
Removable media means you don't have to take a computer and cable
with you to load a new map in the field. If the unit is mounted in a ve-
hicle, there is no need to dismount it and carry it to a computer. The
effective mapping memory capacity of your GPS unit is restricted only
by the capacity and number of memory cards you want to carry with
you, up to the five-card limit. This is a handy feature for long journeys
or for users who can't lug a laptop computer along.
Four factors control Map File size: 1. map detail level option settings,
2. the number of map feature categories turned on, 3. the amount of devel-
oped or naturally occurring features in the area and 4. the amount of terri-
tory, that is, the number of square miles or acres in the area.
Detail Level Options can be set to high or medium. The higher the
level of detail, the bigger the file size.
There are dozens of Map Category Options that you can turn off and
on. They include natural features — such as rivers — and man-made
items such as roads, businesses or other points of interest. The more
categories and subcategories turned on, the bigger the file size.
The amount of development in an area is something you can't con-
trol. For example, one square mile of city streets will make a larger file
than one square mile of wilderness with a few hiking trails.
The amount of territory you include in a map is a major factor. The
more square miles or acres you include, the bigger the file size.
The lessons in the manual were written using MapCreate's default set-
tings, with high detail and all categories turned on. If your first maps

11
don't fit your MMC or SD card, refer to the Help file's Command Refer-
ence section for more detailed instructions on controlling file size.
GPS Data File
This file format contains all the GPS navigation information (waypoints,
event marker icons, routes and trails) used by your GPS unit and MapCre-
ate. The file extension is *.usr (for User file). By default, MapCreate first
saves a GPS Data File to the C:\Program Files\LEI\MapCreate\Data
folder, but if you prefer you can save it direct to your MMC card. If you save
elsewhere, MapCreate remembers that location the next time you save.
Since GPS data files are not encrypted, it does not matter how you move
.usr files around. As with other Windows-based files, you can freely drag
and drop these files back and forth from the hard drive to any MMC.
You can open and make changes in a GPS Data File once it has been
created. The contents can include any combination of waypoints, routes,
trails and event marker icons. The information shows up graphically on
the Master Map as symbols with names. The same information is also
available as text in a list window, such as the Waypoint List window.
Your GPS unit saves field-collected GPS information in the same for-
mat so MapCreate can be used to save valuable travel or adventure
data for a later trip. This also makes it easy to exchange GPS data with
friends using Lowrance or Eagle GPS equipment.
ASCII Text File
This is a universal text file format compatible with word processors and
other software. MapCreate can exchange routes and waypoint lists with
other mapping programs by importing and exporting GPS information
as comma-delimited ASCII text files. ASCII (pronounced "ask-ee") uses
the *.txt file extension. You don't need to work with these files, unless
you plan to exchange routes and waypoints between MapCreate and
other mapping programs. If you want to create a text file manually, or
if you need to manually edit a route or waypoint text file, this is the
waypoint position format MapCreate will export or import:
[latitude],[space][longitude],[space][waypoint name]
Each position is written in degree (decimal) format. For North lati-
tudes, use the latitude with no preceding symbol. For South latitudes, a
minus sign must precede the number, like this: –latitude.
For East longitudes, use the longitude with no preceding symbol. For
West longitudes, a minus sign must precede the number, like this:
–longitude.
The first waypoint in the following example text file is N 36.06079846º,
W 95.78354912º.

12
36.060798, -95.783549, Church 1
36.060784, -95.761647, Turn North 2
36.161831, -95.761529, Turn N-East On Hwy66 (3)
36.162581, -95.753760, Wpt 004*
36.169981, -95.751795, Wpt 005*
36.382616, -95.556565, Turn N-West 6
36.385315, -95.560847, Turn North 7
36.503465, -95.561081, Stop Turn East 8
Text files are saved in the C:\Program Files\LEI\MapCreate\Data
folder. For more information on how to use text files, see the Help file
Command Reference topics "Export GPS Data," "Import Route" and
"Import Waypoint List."
GPS Data Manger (GDM) File
This is an older file format used by MapCreate 5 and MapCreate 4 to
hold navigation data (waypoints and such). MapCreate 6 can open these
files, making the program backward compatible with versions 5 and 4.
The GDM file extension is *.low. Although MapCreate 6 is designed to
load and read older GPS Data Files in the *.low format, MapCreate 6.0
will only save GPS Data Files in the newer *.usr format. Please note
that your MapCreate 6-compatible GPS unit can only read *.usr files.
Atlas File
This is the "raw" file format for layer after layer of cartographic and
hydrographic data on our CDs. You never have to work with these files
directly. MapCreate pulls data from these files to display the Master
Map you see in the main window on your computer. The program com-
bines the information from a Map Border File with the Atlas Files to
make Map Files for your GPS unit.
NOTE: MMC Card Formats
If you have an older MMC that has been formatted by a parallel
port Lowrance MMC Interface card reader, the card format may not
be compatible with your newer USB port MMC card reader. If
that's the case, you can preserve your historic GPS data by copying
it to your hard drive with your older parallel port reader. The older
MMC can then be reformatted so it will work with the newer USB
card reader. To reformat an MMC, refer to the instructions that
came with your USB MMC card reader or your sonar/GPS unit.
If you ever have to format your MMC card, you should know that
MapCreate, as well as Lowrance and Eagle GPS products, will only
read cards that are FAT formatted. MMC cards formatted using
FAT 32 or NTFS will not work with these products.
Latitude Longitude Waypoint Name
In routes, sequence is important. 1st line is wpt 1, 2nd line is wpt 2 and so on.
Comma and space
separate items.
First wpt
Last wpt

13
WARNING:
You should never format an MMC containing a Navion-
icschart or Jeppesenaviation database. Formatting
the MMC will permanently erase the chart or aeronauti-
cal data from the card.
GPS Unit Compatibility
MapCreate 6.3 is compatible with all Lowrance and Eagle mapping
GPS units that use removable MMC/SD cards for map storage. Some
units, however, may need a free software upgrade to work with Map-
Create 6.3. Upgrades are available for download from the web sites,
www.lowrance.com or www.eaglegps.com. Look for the MapCreate 6.3
section, which will contain a list of units that need upgrades. Follow the
links to download your free software upgrade.
If you have questions, call customer service for your GPS unit. Contact
information is on the last page of this manual.
Mapping Detail: There's more here than meets the eye.
The Map Files you make with MapCreate contain more mapping detail
than what is visible on your computer screen. Your MapCreate-
6-compatible GPS unit takes full advantage of this extra information.
Find Highway Exit Services
For example, move your mouse pointer over a highway exit symbol on
the computer map, and all you'll see is a pop-up tool-tip box listing the
name of the exit. However, in a Lowrance or Eagle GPS unit, the same
exit symbol will show a pop-up box with the exit name and symbols of
all the services available near that exit. The GPS unit can also provide
you a list of those services.
At left, an iFINDER GPS screen showing an exit services pop-up icon
box. The iFINDER can then display a text list of those services near
the selected exit, right.
Pop-up
box
Cursor over
exit symbol

14
Find Points of Interest
On the computer master map, moving your pointer over a Point of In-
terest (POI) symbol triggers a pop-up box with the POI's name. With
MapCreate 6.3, when the information is available, the pop-up box also
displays the POI's address and telephone number. This detailed pop-up
only works for items classified as Points of Interest.
Map with pop-up box showing POI information
In a Lowrance or Eagle GPS, all POI's include the name, address and
phone number.
At left, an iFINDER GPS screen showing a POI pop-up name box. At
right, you can call up a page of information on the POI, and the GPS
unit can lead you to the POI's location.
Find an Address
You won't see addresses on your computer map (except listed in the
pop-ups for some POIs). But when the MapCreate information is loaded
into your GPS, you can search for a street address or a street intersec-
tion. In fact, your GPS unit can search by name for virtually every
category of mapping detail contained in MapCreate.
Cursor over
POI symbol
Pop-up
box