LP&No.1 LPSC-015 User manual

Model: LPSC-015
User Manual

IMPORTANT: Please read this manual carefully and completely
before operating this unit and keep this manual for future reference.
BEFORE USE
1. Choose a safe location and avoid placing the unit in direct sunlight or near any heat
source.
2. Avoid environments subject to vibration, excessive dust, cold or moisture.
3. Due to the risk of electrical shock, do not open the cabinet. Should a foreign object
accidentally find its way into the interior of the unit, contact your local dealer.
4. Do not attempt to clean the unit with chemical solvents as this might damage the
finishing. A clean, dry cloth is recommended for cleaning.
5. Keep this manual for future reference.
1. Power/Volume Knob 2. Headphone Jack 3. Status Indicator
4. AUX IN Jack 5.Function Mode Switch Knob
6. USB Port 7.DC IN Jack 8.RCA Output Jack
9. 45RPM Adaptor 10. Auto Stop Switch 11. Speed Switch
12. Tone Arm Lock 13. Ceramic Cartridge 14. Platter
Getting Started
Firmly and securely insert the DC plug of the adaptor to the DC IN Jack on the back of the
unit.
Plug the adaptor’s AC plugs into a power outlet.
Phono Mode
1. Switch the function mode switch knob to PHONO mode. Turn on the power switch. The
status indicator will become red color.

Remark: During the phono mode, please make sure that the AUX IN jack was not
plugged in with the audio cable.
2. Place a record on the turntable platter and select the desired speed (33/45/78) according
to the record. NOTE: when playing a 45RPM record, use the included 45RPM adaptor.
3. Remove the stylus protector. Open the tone-arm lock to release the tone-arm. Push the
lift lever backward to raise the tone-arm and gently move the tone-arm to the desired
position over the record. The turntable will begin to spin when the arm is moved toward
the record. Push the lift lever forward to lower the tone-arm slowly onto the desired
position on the record to begin playing the record. Please note: The record will begin to
spin only when the tone-arm is moved toward the record if the Auto Stop is turned on.
4. If the Auto Stop Control Switch is turned ON, the record will stop automatically when
finished. If Auto Stop Control Switch is turned OFF, the record will NOT stop
automatically when finished.
Remark: AUTO STOP function applies to most 33RPM vinyl records. However, for very few
vinyl records, it will stop when it does not come to the end, or it
will not stop when it comes to the end when AUTO STOP is ON.
5. Turn the VOLUME CONTROL KNOB to adjust the volume.
Bluetooth Mode
1. Switch the function knob to BT. The indicator will become blue color with flashing.
2. Turn on your Bluetooth function on your mobile phone or tablet PC and then search the
turntable player with its name LPSC-015. After pairing and connection, the Bluetooth
indicator will become blue color without flashing, and you can play your music of your
mobile phone or tablet PC on this turntable player.
3. Turn the VOLUME CONTROL KNOB to adjust the volume. The mobile phone or tablet
PC’s volume level also impact the overall volume. Please adjust that as well for needed
volume level.
Remark: During the Bluetooth mode, please make sure that the AUX IN jack was not
plugged in with the audio cable.
AUX IN Mode
1. Switch the function knob to AUX IN mode.
2. Connect your iPod, MP3 player, mobile phones etc. to the AUX IN port with a
3.5mm-3.5mm audio cable (not included).
3. You can enjoy the music of iPod, MP3 player, mobile phones etc. at the turntable player.
4. Rotary the volume knob to adjust the volume. The iPod, MP3 player, mobile phones’
volume level also impact the overall volume. Please adjust that as well for needed
volume level.
Listening to Music Privately

Connect your headphone or earphone to the headphone jack on the front panel and you can
enjoy the music privately.
Listening the Music with External Speaker System
Connect your own speaker system(with power amplifier built-in) to the RCA output jack at
the rear of the unit with an audio cable(not included).

RECORD YOUR VINYL TO YOUR WINDOWS PC
1. Setup
Connect the USB cable with your turntable and your computer. No extra driver is
required.
2. Audacity Installation
Insert the installation CD. Your computer will auto-run the program. Follow the
instructions to complete installation.
If your computer does not auto run, click on the “Start” menu, select “Run” and choose the
CD located on your computer and run “Setup.exe”
3. Run Audacity Program
Double-click on the Audacity program and the Audacity interface window will be displayed
on your computer screen.
4. Playback Control Toolbar
Audacity will display a control toolbar for you to edit and manage your recordings.

5. Playing Your Record
Play the record you want to record by following the procedure described in the section
“LISTENING TO A RECORD”
6. Adjusting Input and Output
Adjust the output and input volume.
7. Recording
Select the RECORD button to start recording while your record is playing.
You will need to position the needle on the record for a few seconds before the track starts,
so that you select the RECORD button at the beginning of your track.
Start playback on the USB turntable. You will see the waveform of the audio on the screen
as it is recording. You will hear the audio coming from the output of your computers
soundcard.
No Audio? - go back to the preference menu and make sure you have “Software
Playthrough” selected and the speaker volume up on your computer.
Press Stop

SAVE YOUR FILE NOW by clicking on “File” followed by “Save Project”
Select the destination and file name for the project and click “Save”
Once finished recording, your screen should display your recording as below.
8. Editing your Recording
Audio Levels
Select your entire recording by selecting “Edit,” then “Select…” then click “All.”
Select the “Effect” menu and choose the desired effect. There are various types of effects
which are described further on Audacity’s website.
Selecting “Normalize” should be used to have Audacity auto-correct volume on the
recording.

Noise Reduction
Drag your cursor over a portion of the audio track which contains unwanted noise. We
recommend using the beginning or end of a track where there is no music and only
noise.

- Select “Effect” and then “Noise Removal” from the drop down menu to bring up the
“Noise Removal Window”
- Click “Get Noise Profile” and the window will close automatically.
- Select the entire track of audio you wish to remove noise from.
- Adjust the amount of audio that you would like to filter by moving the slider in the “Noise
Removal” window. We recommend using the minimum noise removal for optimum sound.
Note: you can preview the audio before removing the noise by clicking on ‘Preview’.

- Click on ‘Remove Noise’.
The Editing Toolbar
The Tools Toolbar