LSTN sound co Beacon 2.0 Operating instructions

Troubleshooting the Beacon 2.0
OVERVIEW
We want you to have the best possible experience with the
Beacon 2.0. If you’re encountering issues with connection
or pairing, try these troubleshooting tips.
Before you begin, make sure both the case and earbuds
are fully charged. The case can sometimes lose charge
during shipping, so if you’ve just received your Beacons
make sure to give them a full charge before use. A fully
charged case will show all 4 bars lit up on the surface.
Initial Pairing
The first time you use your Beacons, remove them both
from the case, and allow them to pair with each other
first. You will know when they are paired because one LED
indicator will flash blue, while the other stays solid blue. A
short confirmation tone will also sound. Once the earbuds
are paired with each other, select ‘LSTN Beacon’ from your
device’s Bluetooth settings.

Troubleshooting the Beacon 2.0
FUNCTIONALITY
If you want to pair the Beacon to a new device, turn off
the original device’s Bluetooth before pairing or forget
the Beacon from its list of devices. This will prevent any
attempt by the Beacon to automatically pair to the first
device.
Automatic Pairing
The Beacon will automatically connect to the most recent
device it was paired with. If it cannot find that device, it
will await connection. If you have previously paired the
Beacon to a device and it is not automatically connecting,
try selecting ‘LSTN Beacon’ from your device’s list of
Bluetooth devices. If this does not work, try forgetting the
Beacon and pairing as a new device.
Right
Earbud
Earbud LED Indicator
Case Charge
Indicator
Le f t
Earbud

Troubleshooting the Beacon 2.0
RESETTING YOUR EARBUDS
1) If you have previously connected to the Beacons, make
sure to disconnect and forget them from your device, and
ensure the case is fully charged.
2) Place them in the charging case for 15 seconds.
3) Take them both out at the same time and simultaneously
press and hold down both buttons on both sides until they
both turn off (approximately 7-10 seconds)
4) Press both buttons at the same time again, and hold
them for 10-15 seconds. The LED will first flash purple,
then blue/red, and then both earbuds will rapidly flash
purple, and will play a descending series of beeps indicating
the earbuds have been reset. Once the reset is complete
you may release the buttons.
5) Place them back in the case for 10 seconds.
6) Remove both earbuds from the case at the same time.
Allow them to pair with each other, and then select ‘LSTN
Beacon’ from your device’s Bluetooth settings.
If your Beacons are having difficulty connecting to each
other, you may wish to reset the earbuds to their default
settings.

Troubleshooting the Beacon 2.0
LED INDICATORS
▸ Both LEDs blinking blue: The earbuds are pairing with
each other. Once they are connected you will hear a short
tone, and the LEDs will turn solid blue.
▸ Both LEDs are solid blue: The Beacons are connected with
each other and with your device.
▸ One LED blinks blue, one LED is solid blue: The Beacons
are connected to each other and are ready to be paired to
your device.
▸ Both LEDs blinking red then blue: The Beacons are not
connected to each other and are searching for a device.
Put them back in the case or turn them off manually and
begin pairing from the beginning.
▸ One or both LEDs are solid purple: The Beacons are
searching for a previously connected device and will con-
nect momentarily.
▸ Both LEDs blinking red: The Beacons are connecting to
the charging case.
▸ Both LEDs solid red: The Beacons are charging in the
case.
▸ One of both LEDs are flashing purple: The Beacons are
being reset, and will be available momentarily