LTH Squareled X-tra 40 Bar 12 User manual

User Manual: Squareled X-tra 40 Bar 12

SquareLED X-tra 40 Bar 12
TILT | ZOOM | SEAMLESS
USER MANUAL

Content
INTRODUCTION ...................................................................................................3
DESCRIPTION........................................................................................................3
SAFETY INSTRUCTIONS ..................................................................................3
DMX-512 control connection........................................................................4
DMX-512 connection with DMX terminator.........................................4
Operation.................................................................................................................4
Display Menu .................................................................................................4
Main functions ..............................................................................................6
DMX functions and values......................................................................8
CLEANING AND MAINTENANCE ................................................................11
INSTALLATION ...................................................................................................11

INTRODUCTION
Thank you for having chosen our LED lighting
Unpack the device, inside the box you should find:
The fixture device
One power cable
One XLR connection cable
This manual
Please check carefully that there is no damage caused by transportation. Should there
be any problems, consult your dealer and don’t install this device.
DESCRIPTION
Features
Light source: 12x40W RGBW Osram LED, Tilt zoom Seamless combination Bar
Lamp lifetime: more than 20000 hours
Scan rate 2000HZ
input voltage: 110-240V AC,50-60HZ
Max power 550W
Electronic zoom: 3.5-40 Degrees
Channel: 20/61 Channel mode
Tilt Motor: 230 degrees
Weight : 14KG
size: 100*10*30cm
IP Rating: IP20
SAFETY INSTRUCTIONS
This device has left the factory in perfect condition. In order to
maintain this condition and to ensure a safe operation, it
is absolutely necessary for the user to follow the safety instructions and warning notes
written in this user manual.
This device falls under protection-class I. Therefore it is essential that
the device should be earthed.
The electric connection must carry out by qualified person.
If the external flexible cable or cord of this luminaire is damaged,
it shall be exclusively replaced by the manufacturer or his
service agent or a similar qualified person in order to avoid a hazard.
Make sure that the available voltage is not higher than stated at the
end of this manual.

Make sure the power cord is never crimped or damaged by sharp edges.
If this would be the case, replacement of the cable must be done by
an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it.
Only handle the power cord by the plug. Never
pull out the plug by tugging the power cord.
Never look directly into the light source, as sensitive
persons may suffer an epileptic shock.
Important
Damages caused by the disregard of this user manual are not subject to
warranty. The dealer will not accept liability for any resulting defects or
problems.
DMX-512 control connection
The product has a DMX 512 input fitted with 3-pin XLR connectors. Screened cables in
compliance with EIA RS-485 specifications and the following characteristics must be
used for connections:
- 2 conductors plus screen
- 120Ohm impedance
- low capacitance
- max. transmission rate 250kBaud.
DMX-512 connection with DMX terminator
For installations where the DMX cable has to run a long distance or is in an electrically
noisy environment, such as in a discotheque, it is recommended to use a DMX
terminator. This helps in preventing corruption of the digital control signal by electrical
noise. The DMX terminator is simply an XLR plug with a 120 OHM resistor connected
between pins 2 and 3, which is then plugged into the output XLR socket of the last fixture
in the chain.
Operation
Display Menu

Main menu
Sub-menu
Level 2 menu
Parameter
DMX Address
001 - 512
Fixture
Ch Mode
STD/EXT
Run Mode
DMX/Host/Sound
Tilt Inv
Close/Open
Manual
Tilt
0 - 255
Tilt Fine
0 - 255
.
0 - 255
.
0 - 255
.
0 - 255
Information
Time
Current Time
xxxh
Total Time
xxxh
Power Count
xxx
Sensor
Tilt
TRUE/FALSE
Zoom1
TRUE/FALSE
Zoom2
TRUE/FALSE
Temp
TRUE/FALSE
Temperature
Head Temp
xxx C
Software Version
Panel
Vx.xxx
Dimmer
Vx.xxx
Factory
Password
0 - 255
Tilt
0 - 255
Zoom1
0 - 255
Zoom2
0 - 255
Red
0 - 255
Green
0 - 255
Blue
0 - 255
White
0 - 255
Fixture Reset
Reset
Run/OFF
Factory
Run/OFF
Display
Language
EN/CH
Display Flip
Normal/Reverse
Display Mode
Show/60s

Main functions
1. address:Current DMX address
A.Setting DMX address by button
press ENTER button when show the address menu, then adjust the DMX address
by pressing [UP] or [DOWN] button
Press [ENTER] to confirm or pressing [ESC] to return to main menu.
B.Setting DMX address by controller
1.Set the DMX value of channel 5 to 10-15,channel 17 to 20-26, channel 7 to
30-36,channel 8 to 40-46,then the devices connected to the controller will enter to
the setting address mode
2. Set the DMX value of channel 1 from 0-59,then you will see the the first number
of the Address change to (channel 1 vaule)/10.
For example,when set the value of channel 1 to 20,the first DMX address number
will be 2(20/10=2) ,
3. Set the DMX value of channel 2 from 0-99,then you will see the the sencond
number of the Address change to (channel 2 vaule)/10.
For example,when set the value of channel 2 to 30,the first DMX address number
will be 2(30/10=3) ,
4.Set the DMX value of channel 3 from 0-99,then you will see the the third number
of the Address change to (channel 3 vaule)/10.
For example,when set the value of channel 1 to 40,the first DMX address number
will be 3(40/10=4) ,
And the DMX address you set by conctroller will be 234.
5. Set the DMX value of channel 4 to 255,then you will save the DMX address
setted by the controller.
Caution: It won’t save the address if the address number is over 512
6. set the value of channel 5-8 out of the value range show on the step 1,and the
device will exit the setting address mode
2. Config
Setting DMX mode
press ENTER button when show the channel menu, then select the DMX mode by
pressing [UP] or [DOWN] button
Setting Dimmer Curve
press ENTER button when show the dimmer curve menu, then select the
dimmer curve by pressing [UP] or [DOWN] button
Setting Cipher
press ENTER button when show the cipher setup menu, then setup cipher by
pressing [UP] or [DOWN] button

Key mode
press ENTER button when show the key mode menu, then select lock or unlock
by pressing [UP] or [DOWN] button
Show Temperature
press ENTER button when show the Temp Uint CS menu, select the way of
showing the fixture’s temperature in ℃or ℉by pressing [UP] or [DOWN]
button
DMX status
press ENTER button when show the DMX Status menu, then select clear value or
hold value by pressing [UP] or [DOWN] button
DMX direct
press ENTER button when show the DMX direct menu, then select DMX direct
positive or negative by pressing [UP] or [DOWN] button
Display mode
press ENTER button when show the Display Mode menu, then select auto or on
by pressing [UP] or [DOWN] button
3. System info
Temperature
press ENTER button when show the Temperature menu, then it will show the
temperature of the fixture
Fixture time
press ENTER button when show the Fixture time menu, then it will show how long
time of the fixture already used
4. Color menu
press ENTER button when show the Color menu, press Enter button to select the
color mode, then adjust the color by pressing [UP] or [DOWN] button
5. White balance
press ENTER button when show the white balance menu, press Enter button to
select the color mode, then adjust the color by pressing [UP] or [DOWN] button
6. Static test
press ENTER button when show the static test menu, select different color by
pressing [UP] or [DOWN] button

7. Auto test
press ENTER button when show the auto test menu, select test mode by pressing
[UP] or [DOWN] button
8. Factory setting
press ENTER button when show the Factory setting menu, adjusting color cablir
by pressing [UP] or [DOWN] button
DMX functions and values
Standard
mode
(20CH)
Chanel
name
Value
Function
1
Tilt
0 - 255
Vertical rotation
2
TiltFine
0 - 255
Vertical fine-tuning
3
Tilt-Speed
0 - 255
Vertical motor speed
4
Zoom All
0 - 255
Enlarge the whole
5
Zoom1
0 - 255
Zoom in 1
6
Zoom2
0 - 255
Zoom in 2
7
Dimmer
0 - 255
Dimming 8bit
8
DimFine
0 - 255
Dimming 16bit
9
Strobe
0 - 3
shut down
4 - 103
Regular stroboscopic, the
speed changes from slow to
faster
104 - 107
turn on
108 - 207
Pulse stroboscopic, the speed
changes from slow to fast
208 - 212
turn on
213 - 225
Random slow strobe
226 - 238
Random medium speed strobe
239 - 251
Random fast strobe

252 - 255
turn on
10
Red
0 - 255
red
11
Green
0 - 255
green
12
Blue
0 - 255
blue
13
White
0 - 255
white
14
Inner Effect
Built-in effect selection
0 - 10
no effect
11 - 13
Static effect 1
14 - 16
Static effect 2
… …
……
67 - 70
Static effect 20
71 - 72
Dynamic effect 1
73 - 75
Dynamic effect 2
… …
……
188 - 190
Dynamic effects 40
191 - 193
Dynamic color effect 1
… …
……
218 - 220
Dynamic color effect 10
221 - 255
Dynamic color effect 11
15
Effect
Speed
0 - 255
Dynamic effect speed (from
slow to fast)
16
LED Mirror
0 - 255
LED lamp beads left and right
mirroring
17
ForColor
0 - 255
Foreground color macro
18
BackColor
0 - 255
Background color macro
19
BackColor
Dimmer
0 - 255
Background dimming
20
Function
Features
Fixture
Reset
101-120
Fixture reset
Reserve
Other
No effect

Extended
mode(60CH)
Chanel
name
Value
Function
1
Tilt
0 - 255
Vertical rotation
2
TiltFine
0 - 255
Vertical fine-tuning
3
Tilt-Speed
0 - 255
Vertical motor speed
4
Zoom1
0 - 255
Zoom in 1
5
Zoom2
0 - 255
Zoom in 2
6
Dimmer
0 - 255
Dimming 8bit
7
DimFine
0 - 255
Dimming 16bit
8
Strobe
0 - 3
shut down
4 - 103
Regular stroboscopic, the
speed changes from slow to
faster
104 - 107
turn on
108 - 207
Pulse stroboscopic, the speed
changes from slow to fast
208 - 212
turn on
213 - 225
Random slow strobe
226 - 238
Random medium speed strobe
239 - 251
Random fast strobe
252 - 255
turn on
9
Red
0 - 255
red
10
Green
0 - 255
green
11
Blue
0 - 255
blue
12
White
0 - 255
white
13
LED1 Red
0 - 255
LED1 red
14
LED1 Green
0 - 255
LED1 green
15
LED1 Blue
0 - 255
LED1 blue
16
LED1 White
0 - 255
LED1 white
17
LED2 Red
0 - 255
LED2 red
18
LED2 Green
0 - 255
LED2 green

19
LED2 Blue
0 - 255
LED2 blue
20
LED2 White
0 - 255
LED2 white
… …
… …
… …
……
57
LED12 Red
0 - 255
LED12 red
58
LED12
Green
0 - 255
LED12 green
59
LED12 Blue
0 - 255
LED12 blue
60
LED12
White
0 - 255
LED12 white
61
Function
Features
Fixture
Reset
101-120
Fixture reset
Reserve
other
No effect
CLEANING AND MAINTENANCE
We recommend a frequent cleaning of the device. Please use a soft lint-free and
moistened cloth. Never use alcohol or solvents!
CAUTION! Disconnect from mains before starting maintenance
operation.
There are no serviceable parts inside the device. Maintenance and
service operations are only to be carried out by authorized dealers.
If you need any spare parts, please use genuine parts.
If the power supply cable of this device becomes damaged, it has to be replaced by
authorized dealers only in order to avoid hazards.
If you have further questions, please contact your dealer.
INSTALLATION
The device must only be installed at a vibration-free, oscillation-free
and fire-resistant location.

Das Lichttechnikhaus Vertriebs GmbH
Rudolf-Diesel-Str. 3, D-89312 Günzburg
Telefon [phone]
Fax [phone]
E-Mail [email protected]
Web www.lth-gmbh.de