Lucci LEDlux 229160 User manual

Installation Instructions
1 | P a g e v 1 . 0 ( 0 6 / 2 0 2 0 )
TOWER SOLAR BOLLARD/TABLE LAMP WITH SENSOR
SKU# 229160, 229161
Rated Voltage 3.7V DC, 2W
Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all
instructions carefully before assembly, installation and use of this product. Please keep instructions for future reference.
Warranty
•This luminaire is covered by a 3-year warranty valid for in-store replacement or refund only.
•The warranty period starts from the date of purchase. Please retain the proof of purchase.
•The warranty is for the luminaire only and does not include the rechargeable battery.
•Warranty will be void if there is any damage due to improper usage or modification to the luminaire.
•Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the
warranty.
Installation Requirements
•Select a suitable location for installation:
−This product is suitable for outdoor use only.
−The mounting point must support 2 times the weight of the luminaire.
−This luminaire is protected against water penetration to IP54 standards, which is splashing water from any
direction.
−The solar panel must have access to direct sunlight to recharge the battery. Avoid any areas where there is
possible shading on top of the solar panel.
−Depending on the luminance of the sun, the charging time required for the battery is approximately 5.5 hours.
−See the Sensor Information section on the next page, for additional information about the sensor detection
range and sensor sensitivity, to select a suitable installation location.
•The luminaire must not be used if the protective shield or shade has been cracked or damaged. Replace the
protective shield or shade before using the luminaire.
•Lay out all the components on a smooth surface and make sure no components are missing before assembling.
If parts are missing, return the complete product to the place of purchase for inspection or replacement.
•Check whether the luminaire has been damaged during transport. Do not operate/install any product which appears
damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.

Installation Instructions
2 | P a g e v 1 . 0 ( 0 6 / 2 0 2 0 )
Sensor Information
PIR (PASSIVE INFRA-RED) SENSOR:
The luminaire has a PIR (Passive Infra-Red) sensing device which continuously scans the operating zone and
immediately switches the luminaire on when it detects any movement in that area. Whenever movement is detected
within the sensor range, the luminaire will switch on automatically to illuminate the area.
NOTE: While there are movements within the sensor range, the luminaire will remain on
SENSOR LOCATION & DETECTION:
•For Pillar Mount, the ideal mounting height is between 1.2m –2m. The detection area is approximately less than 5m,
with an angle of 120°. (Fig. A)
•For Spike Mount, the detection area is approximately less than 3m, with an angle of 120°. (Fig. B)
•The detection area will vary depending on the mounting height and items in the detection area.
•The sensor has increased sensitivity with movement across the detection area. (Fig. C)
•The sensor has reduced sensitivity with movement towards and away from the detection area. (Fig. D)
•If movement is made walking directly towards or away from the sensor and not across its detection area, the detection
range will be substantially reduced.
•The detection area may also alter at different temperatures. PIR sensors are more sensitive in cold weather than
warm weather.
•To avoid false triggering:
−The sensor should be directed away from potential heat sources such as barbecues, air conditioners, exhaust
vents etc.
−Avoid areas with strong electromagnetic disturbance, outside lighting, moving cars, trees, or pets etc.
−Do not aim towards reflective surfaces, such as smooth white walls, swimming pools, ponds etc.
−Avoid installing the luminaire in close proximity to any fluorescent luminaires or ceiling fans. RFI interference may
cause the luminaire to switch on unintentionally.
Fig. A
Fig. B
Fig. C
Fig. D

Installation Instructions
3 | P a g e v 1 . 0 ( 0 6 / 2 0 2 0 )
Installation Directions
Select the type of installation you require before assembly and installation:
This luminaire can be installed as a PILLAR MOUNT or SPIKE MOUNT.
Refer to the corresponding instructions and diagram for the different installation methods.
PILLAR MOUNT (Refer to the diagram below)
1. Remove all packaging material from the product and be careful not to throw away accessories that may be hidden
within the packaging material. If assembly is required, place the luminaire on a smooth non-scratch surface.
2. Remove the mounting bracket from the luminaire by loosening the 4 screws from the mounting bracket. (Fig. A)
3. Use the mounting bracket as a template to mark the screw positions onto the mounting surface. (Fig. B)
4. Install the mounting bracket onto the mounting surface by using appropriately sized mounting screws and anchors.
Ensure the mounting screw and anchors used are suitable for the mounting surface and the surrounding environment.
(Fig. B)
5. Install the luminaire back onto the mounting bracket and secure by tightening the 4 screws. (Fig. C)
6. After the installation is complete, press and hold the touch switch until the blue indicator light turns on. (approximately
3 seconds). (Fig. D) The standby/ambient light (20 lux) will be continuously on until the sensor detects movement
within the sensor range. The luminaire will turn on at 150 lumens for 50 seconds.
NOTE: While there are movements within the sensor range, the luminaire will remain on.

Installation Instructions
4 | P a g e v 1 . 0 ( 0 6 / 2 0 2 0 )
SPIKE MOUNT (Refer to the diagram below)
1. Remove all packaging material from the product and be careful not to throw away accessories that may be hidden
within the packaging material. If assembly is required, place the luminaire on a smooth non-scratch surface.
2. Install the spike to the bottom of the luminaire with the 2 screws provided. (Fig. A)
3. Install the luminaire into the ground. Press and hold the touch switch until the blue indicator light turns on.
(approximately 3 seconds). (Fig. B) The standby/ambient light (20 lux) will be continuously on until the sensor detects
movement within the sensor range. The luminaire will turn on at 150 lumens for 50 seconds.
NOTE: While there are movements within the sensor range, the luminaire will remain on.

Installation Instructions
5 | P a g e v 1 . 0 ( 0 6 / 2 0 2 0 )
Battery Replacement
This luminaire has a built-in rechargeable lithium battery. (ZNL18650E, 3.7VDC, 2200mAh)
The battery has a limited life (1.5 –2 years). After this time, the battery can be replaced following these steps:
NOTE: During the battery replacement, do not scratch or damage the surface of the solar panel, as this will
reduce its efficiency to recharge the battery.
1. Turn the luminaire upside down and place on a smooth, flat non-scratch surface.
2. Loosen the 4 screws in each corner to remove the solar panel from the luminaire. (Fig. 1)
3. Carefully turn the luminaire the right way up and lift the solar panel.
4. Remove the solar panel from the luminaire by following the wires from the solar panel to the luminaire and pull the
connector from the luminaire marked SOL. (Fig. 1 & 2)
5. Locate the wires from the battery to the luminaire and pull the connector from the luminaire marked BATT. (Fig. 2)
6. Remove the old battery and replace with the new battery. Install the battery connector to the luminaire marked BATT.
(Fig. 3)
NOTE: Dispose of exhausted batteries immediately and safely (so they cannot be retrieved by children).
Contact your local council to dispose of the battery safely.
7. Install the solar panel back onto the luminaire and insert the connector into luminaire marked SOL. (Fig. 4)
8. Carefully turn the luminaire upside down and secure the solar panel by tightening the 4 screws in each corner. (Fig. 4)

Installation Instructions
6 | P a g e v 1 . 0 ( 0 6 / 2 0 2 0 )
Safety Tips
•Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning or
making any adjustment to the luminaire.
•Young children should be supervised to ensure that they do not play with the luminaire.
•Handle the luminaire with care to avoid any damage or breakage.
•To clean, wipe with a soft damp cloth. Do NOT soak or immerse the luminaire in water or other liquids.
•Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
•The luminaire must not be used if the protective shield or shade has been cracked or damaged. Replace the
protective shield or shade before using the luminaire.
•The light source of this luminaire is not replaceable; when the light source reaches its end of life, the whole luminaire
shall be replaced. There are no serviceable parts, do not attempt to dismantle or open the luminaire.
•Dispose of exhausted batteries immediately and safely (so they cannot be retrieved by children). Contact your local
council to dispose of the battery safely.
Specifications
SKU #
229160
229161
Rated Voltage
3.7V DC
Rated Wattage
2W
LED Specs
150 lumens, 2W, Warm White –3000K, CRI > 80
Battery Specs
ZNL18650E, 3.7VDC 2200mAh,
Rechargeable Li-ion battery (included)
Battery life (1.5 –2 years)
Replaceable battery*
IP Rating
IP54
Weight
1.4kg
1.5kg
Dimensions
H:340mm L:140mm W:140mm
H:500mm L:140mm W:140mm
*Refer to the instruction manual for more details