Lucky Star 5V-1B User manual

5V-1B
Page I
5V-1B
MAIN BOARD
AT FORM FACTOR
USER'S MANUAL
( VER : 1.1 )

5V-1B
Page II
Copyright
This manual and the information contained herein are
protected by copyright. All rights are reserved.
Warning and disclaimer
This manual is designed to provide information about the
Pentium® main board. Every effort has been made to make
this manual as accurate as possible, but no warranty or
fitness is implied. All the information is provided on an 'as is'
basis. The author and his corresponding publishing company
shall have neither liability nor responsibility to any person
or entity with respect to any loss or damages arising from the
information contained in this manual or from the use of the
system board that accompanies it. Information contained in
this manual is subject to change without notice. The
manufacturer of the system board will not be held responsible
for technical or editorial omissions made herein, nor for the
incidental or consequential damages resulting from its
furnishing, performance, functionality or use. Subsequent
changes to this manual will be incorporated into the next
edition. We welcome any suggestion regarding this manual or
our computer products.
Trademarks
All trademarks are the property of their respective owners.

5V-1B
Page III
Table Of Contents
Chapter 1. Introduction
1
1-1 Overview……………………………………………………..….………….1
1-2 Main
Features……………………………………………………………..2
1-3 Notice ofHardware
Installation……………………………….………3
1-4 Notice of CD Driver Installation……………………………………...4
Chapter 2. Installation
5
2-1 Motherboard Layout……………….……….… .………..……… ……….5
2-2 Jumper Setting……….. ………..….………………….………….……..6
2-3 Connectors and
Jumpers…..……………………………………………7
2-4 SIMM Installation
Procedures…………..……….………………..….18
2-5 DIMM Installation
Procedures…………………………………..……19
2-6 Memory Chart…………………………………………………………….20
Chapter 3. BIOS Setup
21
3-1 Award® BIOS CMOS
Setup…..………………….…….…….………..21
3-2 Standard CMOS
Setup………………………….….………….…….…22
3-3 BIOS Features
Setup….…………………………………….……..…..24
3-4 Chipset Features Setup
…………………………………….…………28
3-5 Power Management
Setup……………………………………………..30
3-6 PNP/PCI Configuration
Setup…………………………….…………..31
3-7 Integrated Peripherals………………………………….………….…..33
3-8 Supervisor/User
Password……………………………………...…….35
3-9 IDE HDD Auto Detection………………….…………………………..38

5V-1B
Page IV
3-10 Load Setup
Defaults…………………………………………….……..41
3-11 Save & Exit
Setup…………………………………………….….……..42
3-12 Quit Without
Saving………………………………………….…….….43
Chapter 4. Index
44
4-1 Memory Map………………………………………..……..….……..……44
4-2 I/O Map…………………………………………………………………….45
4-3 Time & DMA Channels
Map.……………..….…….………………….46
4-4 Interrupt
Map……………………………………….……….…………...46
4-5 RTC & CMOS RAM
Map………….……………………………….…….47

5V-1B
Page 1
Chapter 1 Introduction
1-1Overview
The VT82C580VPX mainboard combines the advanced
capabilities of the VIA Apollo VPX chipset with a high
performance concurrent PCI local bus architecture to provide
the ideal platform for unleashing the unsurpassed speed and
power of the Intel Pentium
processor, Cyrix6x86 and
AMD K5/K6 processors, and can be easily upgraded for 321
pin ZIF socket.
The processor's advanced performance is complemented by a
second level write back PB-SRAM up to 1024KB and main
memory up to 512MB RAM. The main memory is initialed
using the board's two 72-pin SIMM sockets and two 168-pin
DIMM sockets that accept either the new high performance
EDO, BEDO, Fast Page mode DRAM, or synchronous
DRAM(SDRAM).
The VT82C580VPX integrates a full set of I/O features on
board, including two 16550 UART compatible serial ports, one
EPP/ECP capable port, one floppy disk controller, and one
infra-red communication controller. On chip built in Enhanced
IDE controller provides convenient, high speed PCI bus Master
connection capable of four IDE devices, including Hard disk
and CD-ROM.

5V-1B
Page 2
1-2Main Features
Item Description
Socket 7 Supports CPU in a 321- pin ZIF socket
A. Intel
®Pentium
P54C /P55C MMX CPU
B. Cyrix
6x86/6x86L/6x86MX/6x86MII
C. AMD K5/K6/K6-2 processors
Chipset VIA® Apollo VPX chipset
Cache 256K; 512K; 1024K
Memory 2 DIMM/ 2 SIMM
DIMM:
A. EDO RAM or Synchronous DRAM with 168-pin DI
M
modules of 8,16, 32, 64MB, 128MB for 66MHz(5V or 3.3V)
SIMM: take up to 256MB RAM in one bank, using
7
SIMM modules of 1, 2, 4, 8, 16, 32, or 64M
B
supports for EDO, BEDO or fast page mode memory
Exp. Slot 3*16-bit ISA slots and 4* 32-bit PCI expansion slots
I/O Integrrted ITE IT8661F/RF multi I/O chipset th
a
two 16550 UART compatible serial ports, one E
P
capable port, one floppy disk drive connector
,
connector
Flash ROM 128KB
Size 22.0 x 24.0 cm
Special
feature AT power connector

5V-1B
Page 3
1-3Notice of Hardware Installation
A. Check the package before hardware installation
The main board package contains:
* 5V-1B main board
* manual
* cables
* driver & utility / CD
If any of these items is missing or damaged, contact the dealer
from whom you purchase. Leave this main board in its original
package until you are ready to install it.
B. Make Sure power is off during hardware installation
C. No guarantee for CPU over-clock setup
because system chipset does not support.

5V-1B
Page 4
1-4 Notice of CD Driver Installation
This CD contains below drivers:
A.
main boards:
I440BX®, I440EX®, I440LX®, I430TX®, VIA®
VPX, VP3, and MVP3 main boards
B. AGP cards:
S- 6326 and T-985
C. Solo-1:
Ess-solo-1 sound driver
D. GL518SM: CPU voltage /temperature and fan speed
detection software
E.
PCcillin:
anti- virus protection software
The below drivers are not all suitable for 5V-1B. Please rea
d
“Index”
before installing required drivers. “Index” offers all
t
information on the below files.
R
ead “Index” before installing required drivers.
“Index” file is HTML format.
FILES EDIT VIEW HELP
17 Object(s)

5V-1B
Page 5
Chapter 2 Installation
2-1 Motherboard Layout
SOCKET 7 CACHE
CACHE CACHE
CACHE
JP2
JP3
JBF2 JBF1 JBF0
JPW1 JD1
JCK1
JCK2
JCK3
JCK4
JV1
JV2
VT82C585VPXVT82C586A
JROM1 BIOS JP1 IR USB
MOUSE
KB1
COM2
COM1
LPT
P1: AT
ISA1
ISA2
ISA3
PCI2
PCI1
PCI3 PCI4
FDC IDE1 IDE2
DIMM2
DIMM1
SIMM1 SIMM2
VT82C587AT
VT82C587AT

5V-1B
Page 6
2-2 Jumper Setting
Intel® Pentium
Processor Installation
JCK JBFCPU CLOCK SYS.
CLOCK RATIO 1 2 3 4 0 1 2 JPW1 JV1 JV2
P54C 75 MHz 3.3V 50 MHz 1.5X 2-3 2-3 2-3 1-2 OFF OFF OFF 1-2,5-6,7-8 OFF 1-2
P54C 90 MHz 3.3V 60 MHz 1.5X 1-2 2-3 2-3 2-3 OFF OFF OFF 1-2,5-6,7-8 OFF 1-2
P54C 100 MHz 3.3V 66 MHz 1.5X 2-3 1-2 2-3 2-3 OFF OFF OFF 1-2,5-6,7-8 OFF 1-2
P54C 120 MHz 3.3V 60 MHz 2X 1-2 2-3 2-3 2-3 ON OFF OFF 1-2,5-6,7-8 OFF 1-2
P54C 133 MHz 3.3V 66 MHz 2X 2-3 1-2 2-3 2-3 ON OFF OFF 1-2,5-6,7-8 OFF 1-2
P54C 150 MHz 3.3V 60 MHz 2.5X 1-2 2-3 2-3 2-3 ON ON OFF 1-2,5-6,7-8 OFF 1-2
P54C 166 MHz 3.3V 66 MHz 2.5X 2-3 1-2 2-3 2-3 ON ON OFF 1-2,5-6,7-8 OFF 1-2
P55C 166 MHz 2.8V/3.3
V
66 MHz 2.5X 2-3 1-2 2-3 2-3 ON ON OFF 7-8 1-2,3-
4
1-2
P54C 180 MHz 3.3V 60 MHz 3X 1-2 2-3 2-3 2-3 OFF ON OFF 1-2,5-6,7-8 OFF 1-2
P54C 200 MHz 3.3V 66 MHz 3X 2-3 1-2 2-3 2-3 OFF ON OFF 1-2,5-6,7-8 OFF 1-2
P55C 200 MHz 2.8V/3.3
V
66 MHz 3X 2-3 1-2 2-3 2-3 OFF ON OFF 7-8 1-2,3-
4
1-2
P55C 233 MHz 2.8V/3.3
V
66 MHz 3.5X 2-3 1-2 2-3 2-3 OFF OFF OFF 7-8 1-2,3-
4
1-2
AMD K5/K6/K6-2 Processor Installation
JCK JBFCPU CLOCK SYS.
CLOCK RATIO 1 2 3 4 0 1 2 JPW1 JV1 JV2
K5-PR 75 3.52V 50 MHz 1.5X 2-3 2-3 2-3 1-2 OFF OFF OFF 1-2,3-4,5-6,7 OFF 1-2
K5-PR 90/PR120 3.52V 60 MHz 1.5X 1-2 2-3 2-3 2-3 OFF OFF OFF 1-2,3-4,5-6,7 OFF 1-2
K5-PR100/PR133 3.52V 66 MHz 1.5X 2-3 1-2 2-3 2-3 OFF OFF OFF 1-2,3-4,5-6,7 OFF 1-2
K5-PR166 3.52V 66 MHz 2.5X 2-3 1-2 2-3 2-3 ON ON OFF 1-2,3-4,5-6,7 OFF 1-2
K6-PR166 2.9V/3.3V 66 MHz 2.5X 2-3 1-2 2-3 2-3 ON ON OFF 1-2,7-8 1-2,3-
4
1-2
K6-PR200 2.9V/3.3V 66 MHz 3X 2-3 1-2 2-3 2-3 OFF ON OFF 1-2,7-8 1-2,3-
4
1-2
K6-PR233 3.2V/3.3V 66 MHz 3.5X 2-3 1-2 2-3 2-3 OFF OFF OFF 5-6,7-8 1-2,3-
4
1-2
K6-PR233 3.3V/3.3V 66 MHz 3.5X 2-3 1-2 2-3 2-3 OFF OFF OFF 1-2,5-6,7-8 1-2,3-
4
1-2
K6-PR266 2.2V/3.3V 66 MHz 4X 2-3 1-2 2-3 2-3 ON OFF ON 3-4 1-2,3-
4
1-2
K6-PR300 2.2V/3.45V 66 MHz 4.5X 2-3 1-2 2-3 2-3 ON ON ON 3-4 1-2,3-
4
2-3
K6-2 266 2.2V/3.3V 66 MHz 4X 2-3 1-2 2-3 2-3 ON OFF ON 3-4 1-2,3-
4
1-2
(+)K6-2 300 2.2V/3.3V 66 MHz 4.5X 2-3 1-2 2-3 2-3 ON ON ON 3-4 1-2,3-
4
1-2
Cyrix
6x86 Processor Installation
JCK JBFCPU CLOCK SYS.
CLOCK RATIO 1 2 3 4 0 1 2 JPW1 JV1 JV2
P120+ M1 3.52V 50 MHz 2X 2-3 2-3 2-3 1-2 ON OFF OFF 1-2,3-4,5-6,7 OFF 1-2
P133+ M1 3.52V 55 MHz 2X 2-3 2-3 1-2 2-3 ON OFF OFF 1-2,3-4,5-6,7 OFF 1-2
P150+ M1 3.52V 60 MHz 2X 1-2 2-3 2-3 2-3 ON OFF OFF 1-2,3-4,5-6,7 OFF 1-2
P166+ M1 3.52V 66 MHz 2X 2-3 1-2 2-3 2-3 ON OFF OFF 1-2,3-4,5-6,7 OFF 1-2
P133+ 2.8V/3.3V 55 MHz 2X 2-3 2-3 1-2 2-3 ON OFF OFF 7-8 1-2,3-
4
1-2
P150 + 2.8V/3.3V 60 MHz 2X 1-2 2-3 2-3 2-3 ON OFF OFF 7-8 1-2,3-
4
1-2
P166+ 2.8V/3.3V 66 MHz 2X 2-3 1-2 2-3 2-3 ON OFF OFF 7-8 1-2,3-
4
1-2
P200+ 2.8V/3.3V 75 MHz 2X 1-2 2-3 1-2 2-3 ON OFF OFF 7-8 1-2,3-
4
1-2
MX PR 166 2.9V/3.3V 66 MHz 2X 2-3 1-2 2-3 2-3 ON OFF OFF 1-2,7-8 1-2,3-
4
1-2
MX PR 200 2.9V/3.3V 75 MHz 2X 1-2 2-3 1-2 2-3 ON OFF OFF 1-2,7-8 1-2,3-
4
1-2
MX PR 233 2.9V/3.3V 75 MHz 2.5X 1-2 2-3 1-2 2-3 ON ON OFF 1-2,7-8 1-2,3-
4
1-2
MII PR 300 2.9V/3.3V 66 MHz 3.5X 2-3 1-2 2-3 2-3 OFF OFF OFF 1-2,7-8 1-2,3-
4
1-2
Double check the jumper setting and make sure it is correct.
(+)Chipset specification does not support100 MHz system clock CPU like
AMD® K6-2 300 and K6-2 350, and there is no guarantee for over-clock
setup beyond chipse spec. The above K6-2 300 is only for reference and
needs to set under 66 Mhz.

5V-1B
Page 7
2-3 Connectors and Jumpers
COM1/COM2: Serial port connector
Serial Port connector supports 16550a high speed
communication port that send/receive 16 bytes FIFOs.
IDE1, IDE2: Primary, Secondary IDE connector
PCI IDE controller supports up to four hard disk drivers, CD
ROM, 128MB floppy and other devices.
FDC: Floopy disk connector
IDE2 IDE1 FDC
COM1
COM2

5V-1B
Page 8
IR: I.R.(Infra-red) connector
I.R Connector Pin Out
Pin1
RX Pin2 GND Pin3 TX Pin 4 +5V Pin5 RXH Pin6 VCC Pin7 GND
IR uses the same I/O port as COM2. There is no hardware
jumper setting for I.R./COM2 on this main board but
the user
needs to set proper BIOS (refer to page 32) setup for “HP
SIR,” “ASKIR,” or “Disabled” (default) under “IR Address
Selection” of intergrated Peripherals”
according to the
following table.
BIOS:
Integrated
Peripherals
IRDA 1.0 ASKIR Disabled
(default)
I.R FunctionUse IRDA 1.0
on
I.R.connector
Use Amplitude
shift keyed I.R.
on I.R. connec
t
Use COM2
Pin1

5V-1B
Page 9
JCK1 – JCK3: CPU speed selector
JCK4: PCI working frequency
JCK4 PCI working frequency
1-2 CPU/2
CPU
(MHz) JCK1 JCK2 JCK3 Demo.
50 2-3 2-3 2-3
55 2-3 2-3 1-2
60 1-2 2-3 2-3
CPU
(MHz) JCK1 JCK2 JCK3 Demo.
66 2-3 1-2 2-3
75 1-2 2-3 1-2
NOTE: JCK4 is PCI working
frequency selector.
Pin 1
JCK1
JCK2
JCK3
JCK4
Pin 1
Pin 1
JCK1
JCK2
JCK3
JCK4
JCK1
JCK2
JCK3
JCK4
32 Mhz: 2-3 CPU/2: 1-2

5V-1B
Page 10
2-3 32 MHz (default)
JD1: DIMM voltage selector
JP1: RTC
JD1 DIMM voltage
1-3, 2-4 5V
5-7, 6-8 3.3V (default)
Pin
1
Pin 7
5V DIMM
Pin 1
Pin 7
3.3V DIMM
Pin1
JP1 RTC
1-2 Normal (default)
2-3 Clear CMOS

5V-1B
Page 11
JP2: Case connector
SU-SW: Suspend Mode Interrupt of 2-pin connector
SU-SW is
“Break switch setting.”
When SU-SW is turned
from open to close and back to open(touch the 2-pin jumper
once), the system will enter suspend mode.
JP3: Turbo-LED
JBF0- JBF2: CPU ratio selector
PW-LED
KEYLOCK
HD-LED
RESET
SPEAKER
SU-LED
SU-SW
(SOFTPWR)
+
+
+
+
+
+
JP3
Turbo-LED
Pin1

5V-1B
Page 12
JBF0 JBF1 JBF2 CPU Ratio Demo.
off off off 1.5x/3.5x
on off off 2x
on on off 2.5x
off on off 3x
on off on 4x
on on on 4.5x
off on on 5.0 x
off off on 5.5x
CPU ratio 5x and 5.5x are only for references.
JPW1: CPU Vcore seletor
Pin 1 Pin 7
Pin 2 Pin 8
Pin1
JBF0 JBF2
JBF1

5V-1B
Page 13
JROM1: Flash ROM voltage selector
JV1: CPU voltage selector
JPW1 V-core Demo.
3-4 2.2V
1-2,3-4,5- 2.7V
7-8 2.8V
1-2,7-8 2.9V
JPW1 V-core Demo.
5-6,7-8 3.2V
1-2,5-6,7-8 3.3V
1-2,3-4,5-6,7
-
3.5V
Pin1
Single
Voltage CPU
Pin3 Pin1
Dual
Voltage CPU
Pin3
Be sure to set the right jumper setting for
CPU Vcore.
Pin1
JROM1 Flash ROM voltage selector
1-2 Winbond®, Atmel®, SST®
2-3 Intel®, MXIC®

5V-1B
Page 14
JV2: CPU type selector
KB1: Keyboard Connector
JV2 CPU type(brand)
selector
1-2 Cyrix®, Intel® AMD®
2-3 AMD® K6-300
Pin1
Cyrix®, Intel®,
AMD® Pin1
AMD® K6-300
JV1 CPU voltage selector
Off Single voltage
1-2,3-4 Dual voltage

5V-1B
Page 15
LPT: Parallel Port Connector
Parallel Port connector supports standard printer port,
enhanced parallel port, extended capabilities parallel (ECP).
Mouse: PS/2 mouse connector
Mouse connector support 5-pin PS/2 mouse
Pin Description
1 Keyboard Clock
2 Keyboard Data
3 N.C.
4 Ground
5 +5 Vcc
Pin1

5V-1B
Page 16
P1: AT power connector
Pin Description Pin Description
1 Power Good 7 GROUND
2 +5V DC 8 GROUND
3 +12V DC 9 -5V DC
4 -12V DC 10 +5V DC
5GROUND 11+5VDC
6GROUND 12+5VDC
USB(Universal Serials Bus) connector
USB connector supports USB devices.
Pin1 Pin1
Mouse PS /2 mouse
Pin1 MS CLK
Pin2 MS Data
Pin3 NC
Pin4 GND
Pin5 VCC