lumishore Flood Light 4 User manual

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
1
45-0185-RevB
Flood Light 4” Installation Manual
Voltage
10-31VDC
Colour Output
Single Colour 4”
Amps (max)
1.7A
Please note use of Nylon
washers
Flood Light
Light Bracket
M6 Fasteners
Installation Instructions:
1. Select mounting location. Mounting location should be at and durable.
2. Using a suitable bit, drill the bracket hole. Bracket has a 6.5mm hole suitable for an M6 bolt (supplied), a louvre feature has
been added to lock onto the bolt head and to avoid spinning when tightening.
3. Drill a 6mm (0.236in) hole for the cable. The cable should always be in a ‘xed‘ position, no movement or rotation.
The cable entry should be made watertight, the use of a cable gland is recommended.
4. Fix bracket in place using supplied M6 bolt and nylon insert nut. Apply the appropriate torque based on xings used and
mounting surface.
5. Mount the ood light to bracket using the supplied M6 bolt, washers and nylon insert nut. Ensure nylon washers are
placed on the inside of the stainless steel bracket. Tighten to a torque of 5Nm, DO NOT overtighten.
Please read the following pages before attempting installation to ensure complete understanding of
Lumishore Flood Light 4”. This product should only be installed, inspected, and maintained by a quali-
ed electrician only, in accordance with all applicable electrical codes. Be certain electrical power is OFF
before and during installation and maintenance.

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
2
Wiring Diagrams:
Wiring should be carried out as per ABYC guidelines. The Lumishore Flood Light 4” will operate with a simple On/O switch, it
can also be controlled by MFD via LUX Light Control Module and Lumi-Link Command Center. For further electrical installation
instructions and wiring diagrams please refer to the LUX Light Module installation guide (45-0145). Each lighting circuit must
be fused accordingly.
Light Operation (Momentary switch):
1. Press switch once to turn ON.
2. Press and hold to dim lights.
3. Press switch once to turn OFF.
Up to 5 lights - MFD Control via LUX Light Control Module
Light Operation (Latching switch):
1. Turn switch ON to power light at full power.
2. Toggle switch once to begin dimming cycle.
3. Toggle switch again to pause dimming cycle.
4. Turns switch OFF for 5 seconds to restart at full power
Switch (Latching)
Yellow
(No connect)
Fuse
Yellow
(No connect)
Single switch wiring - No MFD control via LUX Light Control Module
RED - 10-31V
BLK - GND
10-31v
GND
LUX Light
Module
MFD Control
(optional) Switch (momentary)
RED - PWR
BLK - GND
YEL - DATA
Red and Blue
wires ONLY
1 2
5
3
4
Lumi-Link
Command Center

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
3
Light Operation (Momentary switch):
1. Press switch once to turn ON.
2. Press and hold to dim lights.
3. Press switch once to turn OFF.
Cleaning and Maintenance:
Use only soap and water to clean the light using a soft cloth. DO NOT use any chemical claners and DO NOT power wash.
Inspection of the light should be carried out regularly.
Warranty:
LUMISHORE Ltd warrants the Flood Light 4” to be free from defects in workmanship and materials for a period of two years,
starting from the date of original purchase. Misuse, abuse, improper installation, neglect, improper shipping, damage caused
by disasters such as re, ood, and lightning, installation by unqualied personnel, unauthorized repair or modication will
void this warranty. For the avoidance of confusion and doubt, non-compliance with all installation, maintenance and operating
instructions in this document constitute non-conformance with warranty terms.
Note : Black wire from each light and LUX Module should connect to common ground
More than 5 lights (max 16) - MFD Control via LUX Light Control Module
10-31v
GND
Cut & Isolate
RED & BLK
LUX Light
Module
To Lumi-Link
Command Center
and MFD
Switch (momentary)
1
6
2
5
3
4
RED
10-31v
BLK
GND
RED
10-31v
BLK
GND
RED
10-31v
BLK
GND
RED
10-31v
BLK
GND
RED
10-31v
BLK
GND
RED
10-31v
BLK
GND