lumishore Lumi-Link EOS STV 2204-i Troubleshooting guide
Lumi-Link Display STV 2204-i Installation & Operating Guide
www.Lumishore.com 1
45-0139-REV-2
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 | Info@Lumishore.com
Lumishore USA 7137 24TH Court East Sarasota, Florida 34243 |(941) 405-3302 | Sales@LumishoreUSA.com
Lumi-Link Display 2204-i Installation & Operating Guide
The intuitive EOS STV 2204-i is a dedicated glass-bridge touch screen and rotary dial display, which
allows the vessel owner to achieve unrivalled levels of color options and lighting modes over the full
color spectrum. The Lumi-link display features a simple to use palette wheel for color selection,
horizontal slide bar for quick adjustments to lighting intensity, control of lighting across multiple
zones with optional presets, and the ability to choose from pre-programmed eect modes like
strobe, sweep or cycle and the unique ‘Sound-to-Light’, which makes for the ultimate party accessory.
With inbuilt Wi-Fi, the lights can be activated and controlled via Apple IOS, Android, or any other
device with a web browser.
The world’s rst marine lighng API (Applicaon Programming Interface) allowing
plug-&-play integraon of Lumishore underwater lighng systems with cered Mul
Funcon Displays (MFDs) creang a centralized control plaorm for the enre vessel
reducing helm cluer and simplifying vessel operaon. www.lumishore.com/lumi-link
EOS STV 2204-i
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 | Info@Lumishore.com
Lumishore USA 7137 24TH Court East Sarasota, Florida 34243 |(941) 405-3302 | Sales@LumishoreUSA.com
Lumi-Link Display Components
STV 2204-i Basic Dimensions
Mounting Screws
Protective Sun
Cover Mounting Bracket
EOS STV 2204-i
2
92mm
(3.62in)
88.76mm
(3.50in)
92mm
(3.62in)
10mm
(0.394in)
118mm
(4.64in)
83mm
(3.27in)
83mm
(3.27in)
Note: Power Cables Not Shown
R 20mm
(0.78in)
STV 2204-i Installation Guide
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 | Info@Lumishore.com
Lumishore USA 7137 24TH Court East Sarasota, Florida 34243 |(941) 405-3302 | Sales@LumishoreUSA.com 3
STV 2204-i Mechanical Installation
94mm(3.70in)
Screw Bracket in place
using supplied bolts
The Lumi-Link Display has been designed to be mounted inside or outside within the cockpit or
dash board of the vessel.
For external installations or where water may access the unit it is recommended that an
appropriate Marine sealant is used between the back of the controller and the surface.
Installation Considerations:
• Select a suitable at surface that is accessible from behind.
• Ensure there are no obstructions and there is adequate clearance behind the surface to allow for
the Lumi-Link Display cable entry and positioning. (Ensure the chosen position also has easy
cable routing to the Lumi-Link Command Center or MFD Network expansion port)
Installation Procedure:
1. Cut the hole to the correct size (83mm x 83mm), and ensure there is enough clearance behind
the mounting panel for the controller to t into, and enough room behind to connect the cables
and t the bracket.
NB: Extreme care should be taken to cut the hole to the correct size. Always cut a smaller hole
than necessary and le outwards until it is the correct size.
2. Feed the Lumi-Link Display through the hole and then using the bracket provided lock in place.
Using the screws supplied screw the bracket to secure controller in place. Do not exceed 1Nm
torque force on each screw.
NOTE : The Lumi-Link Display is designed to t panels between 2mm to 25mm in thickness
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 | Info@Lumishore.com
Lumishore USA 7137 24TH Court East Sarasota, Florida 34243 |(941) 405-3302 | Sales@LumishoreUSA.com
STV 2204-i Electrical Installation
Cable Connections
4
• The Lumi-Link Display is for 12/24volt DC operation.
Under no circumstances should the Controller be connected directly to Mains AC voltage.
• Always use a suitable fuse or circuit breaker to protect the complete system.
Connecting the RJ45 Ethernet Cable:
The Lumi-Link Display can be connected directly to a Lumi-Link Command Center or connected to
a the vessels MFD network . See wiring diagrams on following pages.
Using a Shielded Ethernet cable (min Cat5e) plug one side into the back of the Lumi-Link Display
and the other side into the Lumi-link command center or MFD network.
The supplied RJ45 IP68 cover should be used to make all connections waterproof.
Power Cable Key:
Power to the controller is fed via the Red and Black wires. Care should be taken to ensure the
correct voltage and polarity
• Red V+ (10 - 30V DC)
• Black V- (Ground)
• Max Current Draw @ 12V = 300mA
M12 Cable
Gland
Ethernet
Jack
Red = 10-31v
Black = GND
2000mm
Power Cable Sealing
Nut
Support
Seal
Housing
RJ45 IP68 Cover
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 | Info@Lumishore.com
Lumishore USA 7137 24TH Court East Sarasota, Florida 34243 |(941) 405-3302 | Sales@LumishoreUSA.com
STV 2204-i Overview and Basic Operation
NOTE : When in standby mode, power to the system will still be active until power is disconnected using a
master switch or circuit breaker.
A Suncover is provided to protect the controller from harmful UV rays from the Sun
and general weathering and also protects the device from accidental operation.
Always ensure the Suncover is in place when the controller is not in use.
5
The Lumi-Link Display is very easy to use, It is a touch screen device but can also be used with the
rotary dial. Use the rotary dial to move the cursor around the screen, pressing the rotary dial will
select the icon/slider bar or text that is highlighted.
• Power/Standby Button – Press once to turn the Display ON. Note: The lights will not turn on
until a mode is selected. Press again to turn OFF (Standby mode) - Lights will stay on unless the
zone has been switched o.
NOTE : When Power is rst applied the display may take a few minutes to nd and display control pages
• Back button – press the back button to return to the previous mode or page. Press and hold the
back button for 3 seconds to refresh the screen. Press and hold for >10seconds to reboot the
device.
• Rotary Dial – Use the rotary dial to scroll through the icons, the cursor position will be shown by
an outer glow around the icon. Push the centre of the Rotary dial to select an Icon or slider.
• Power Button PRESS AND HOLD – press and hold for more than 3 seconds to enter settings
page.
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 | Info@Lumishore.com
Lumishore USA 7137 24TH Court East Sarasota, Florida 34243 |(941) 405-3302 | Sales@LumishoreUSA.com
STV 2204-i Overview and Basic Operation
6
Select the Zone power icon to expand the function
menu.
Choose from Zone On/O, Color palette, preset and
favourites color cycle, strobe mode, sweep mode or
sound to light.
Select the middle icons to display the slider controls.
The slider functions change depending on what
screen is being displayed. Intensity, speed, white
balance etc.
Select the Preferences icon to enter setup modes.
Use this for initial setup, light discovery, about
screen, zone and scene editing and password
protection.
!"
!
!"
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 | Info@Lumishore.com
Lumishore USA 7137 24TH Court East Sarasota, Florida 34243 |(941) 405-3302 | Sales@LumishoreUSA.com
STV 2204-i Overview and Basic Operation
7
!
Check the Wi-Fi and DHCP settings before connecting to the Lumi-Link command Center or MFD
Network
Power Button - Press and Hold (3 Seconds) for Display Settings, Press and hold (3 Seconds) again to return
to Lumi-Link Lighting Control page.
Change SSID (Wi-Fi name displayed) and choose a
suitable password for the network;
Default Password: lumishore
If the Wi-Fi signal is intermittent it may be a very
busy channel, other equipment onboard could be
using the same channel. Try changing the Wi-Fi
channel to improve signal strength.
Inbuilt Wi-Fi Settings for direct connection to Lumi-Link Command Center
When connected directly to the Lumi-Link Command Center turn the Wi-Fi and DHCP settings on. Press and
hold the Wi-Fi tab to edit the Wi-Fi settings...
**DHCP Settings - There should only be one DHCP server on a network. Only switch the DHCP server on
if the Lumi-Link Display is connected directly to the Lumi-Link Command center.
If the Lumi-Link Display is connected to an MFD network or vessels onboard Newtork router then the
DHCP server should be switched o at all times.
lumishore
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 | Info@Lumishore.com
Lumishore USA 7137 24TH Court East Sarasota, Florida 34243 |(941) 405-3302 | Sales@LumishoreUSA.com
STV 2204-i Electrical Installation - Continued
8
Direct Connection to Lumi-Link Command Center
!"
!
!"
Connection to Garmin Network use Garmin GMS10 Port Expander
Settings Page -
check before
connecting device
Wi-Fi = ON
DHCP = ON
use inbuilt Wi-Fi for
connection to smart device
Wi-Fi = OFF
DHCP = OFF
Note: Use MFD Wi-Fi for
connection to smart device
Settings Page -
check before
connecting device
!!"#$
%&
%'(!
)*+
!!"#$
%&
&+,
-
Note: To prevent the GMS10 switching o when the MFD is turned o connect its yellow wire to Ground.
YEL = GRND
BLK = GRND
RED = VDC+
Garmin GMS10 Wiring
Connections
!!"#$
%&
%'(!
)*+
!!"#$
%&
&+,
-
STV 2204-i Electrical Installation - Continued
Connection to Navico Network use Navico NEP-2 Network Port Expander
Connection to Raymarine Use HS5 SeaTalk Network Switch
! "#
! $%
"$&
!
# '(()*)
!
# '(()*)
+,-./0 +,-./0
!"
"#$%"%&'
(
(
$)*+,,
$)*+,,
Wi-Fi = OFF
DHCP = OFF
Note: Use MFD Wi-Fi for
connection to smart device
Wi-Fi = OFF
DHCP = OFF
Note: Use MFD Wi-Fi for
connection to smart device
Settings Page -
check before
connecting device
Settings Page -
check before
connecting device
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 | Info@Lumishore.com
Lumishore USA 7137 24TH Court East Sarasota, Florida 34243 |(941) 405-3302 | Sales@LumishoreUSA.com 9
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 | Info@Lumishore.com
Lumishore USA 7137 24TH Court East Sarasota, Florida 34243 |(941) 405-3302 | Sales@LumishoreUSA.com
Product Support, Warranty & Troubleshooting
10
Warranty
LUMISHORE Ltd warrants the Lumi-Link Display to be free from defects in workman-
ship for a period of two years, starting from the date of original purchase. Should your
lighting system have a problem during this period, please contact your dealer as soon
as you become aware of the defect.
Misuse, abuse, improper installation, neglect, improper shipping, damage caused by
disasters (e.g. re, ood and lightning), installation by unqualied personnel, unau-
thorized repair or modication will void this warranty. For the avoidance of confusion
and doubt, non compliance with all installation, maintenance and operating instruc-
tions in this document constitute non conformance with warranty terms.
Full warranty details are available at www.lumishore.com.
Product Support
United Kingdom +44(0)208 144 1694, or France +33(0)493 582 537.
Table of contents
