LuxenHome WHF727 User manual

Product Name:
Rustic Brown Resin Pitcher and Urns Birdbath Bowl Outdoor Fountain
SKU #:
WHF727
Instruction Manual
SAVE THESE INSTRUCTIONS – This manual contains
important safety and operating instructions for power units.
Thank you for purchasing this LuxenHöme product. This product has been manufactured with the highest
standards of safety and quality.
PLEASE READ ALL INSTRUCTIONS BEFORE ASSEMBLY.
Unpack all parts from Styrofoam and bubble wrap inside the carton to ensure there are no missing or damaged
parts. If any parts are missing or damaged, do not attempt to assemble or use the product.
CARTON CONTENTS:
Description
Quantity
Fountain
1
Pump
1
Pitcher w/ Tube
1
Bird
1
Compatible Pumps for this fountain:
Pump Model No.
JR450
JB450
YH707
Tools required for assembly: No tools required for assembly.
Assembly Instructions:
1. Unpack the contents of the box and check to make sure that all items are accounted for and in good condition.
2. Select a flat, level surface for the assembly and final location of your fountain.
3. From the opening at the back of the fountain base, insert the water supply tube into the pump outlet. Place the
pump upright in the basin and draw the pump power cord out of the fountain back. Insert pitcher and bird to
fountain. ①
4. Add clean water into the bottom pot. The water level should be approximately 1.18in (30mm) lower than the
edge of the pot. The pump will be submerged in the water. ②
5. Connect the pump power cord to a ground fault circuit interrupter (GFCI) outlet and the product will begin to
function as intended. ③
6. To eliminate the possibility of water damage around your fountain, check for leaks and excessive splashing
after the initial setup of your fountain. It is highly recommended that this fountain be placed in an area where it
cannot be damaged.
7. Do not leave your fountain running for extended periods of time when no one is present to observe the
performance.
8. Check the area around your fountain on a regular basis to ensure that there is no leakage.
9. Please refresh the fountain with water each week to ensure it in good condition.
10. Do not add any harmful chemicals to the water as it may alter the paint finish.

Product Name:
Rustic Brown Resin Pitcher and Urns Birdbath Bowl Outdoor Fountain
SKU #:
WHF727
Instruction Manual
SAVE THESE INSTRUCTIONS – This manual contains
important safety and operating instructions for power units.
Note: The above diagram is for illustrative purposes only.
1
2
3

Product Name:
Rustic Brown Resin Pitcher and Urns Birdbath Bowl Outdoor Fountain
SKU #:
WHF727
Instruction Manual
SAVE THESE INSTRUCTIONS – This manual contains
important safety and operating instructions for power units.
MAINTENANCE OF YOUR PUMP:
•Keep the water clean – clean water will prolong the useful life of your pump.
•Use a pre-filter on your pump if available.
•Regular cleaning of the pump will be necessary depending on the environment in which it is operated. Clean
the pump when it is visibly soiled or when a noticeable drop in performance is detected. Failure to clean the
pump will result in overheating of the pump and the voiding of the warranty!
•Before cleaning, always disconnect the pump from the power source.
•Disassemble the pump by removing the inlet screen & the impeller housing. Remove the impeller/rotor
assembly by gently pulling on the impeller blades. Use a soft cloth or brush to clean the area inside of the
pump where the impeller/rotor assembly was. Clean the inlet screen, impeller housing & impeller in warm
soapy water. Reassemble the pump and inspect for proper operation.
MAINTENANCE OF YOUR FOUNTAIN:
•Unplug the pump from electric power before servicing, cleaning, or moving.
•Keep water clean - using clean water will reduce mineral deposits and improve water clarity.
•Clean the fountain periodically to prevent mineral deposits and contamination. Use warm soapy water and a
stiff brush for heavily stained surfaces. Do not use harsh chemicals as this will damage the finished surface
and void the warranty.
•Add clean water periodically to ensure that the pump is fully submerged in water.
•Disconnect the power and empty the basin if the fountain will not be used for an extended time.
•If installed outdoors and in a frozen area of the country, ensure that all water is removed, and the unit is
completely dry. This product is NOT to be operated below 41℉(5℃) freeze damage may occur.
Special Warnings and Cautions:
CAUTION:
•The pump has been evaluated for use with water only.
•Do not use the pump in water exceeding 35ºC / 95ºF.
•Do not use the pump in flammable liquids.
•Do not use the pump for industrial purposes.
•Do not use the pump in vehicles or on ships or aircraft or swimming pools.
•Do not use the pump in a location where special conditions prevail, such as the presence of a corrosive or
explosive atmosphere (dust, vapor, or gas).
•Do not let the pump run dry. The pump must be completely submerged for proper operation and cooling.
•Do not lift the pump by its power cord.
•Keep the plug dry. Do not expose the plug to water or steam.
•Before connecting to the power source, make sure that the pump is assembled and completely submerged in
water.

Product Name:
Rustic Brown Resin Pitcher and Urns Birdbath Bowl Outdoor Fountain
SKU #:
WHF727
Instruction Manual
SAVE THESE INSTRUCTIONS – This manual contains
important safety and operating instructions for power units.
•Check the water level regularly to ensure the pump is completely submerged during operation. The pump
should be fully submerged during operation. Do not add water while operating the product. Always disconnect
the pump from the power source before adding water.
WARNINGS:
•To reduce the risk of electric shock, connect only to a properly grounded, grounding-type receptacle.
•To reduce the risk of electric shock, use the pump only for portable self-contained fountains no larger than 5
feet in any dimension.
•Do not exceed the voltage shown on the pump.
•Always disconnect the pump from the power source prior to beginning any maintenance or work on the pump
or fountain.
•Inspect the power cord for damage before installation and/or maintenance. Replace the entire pump if
damage is found.
•For pumps with a 3-prong, grounded type plug, do not remove the grounding pin from the plug on the power
cord.
TIPS AND TROUBLESHOOTING:
1. Ensure that the pump’s flow control switch is set to maximum (+) before operating. Once the flow is
established, the pump can be adjusted downward to the desired level.
2. If the pump operates, but there is no flow, check to ensure the pump is fully submerged.
3. If the pump operates, but there is no flow, check the supply tubing for kinks and correct it.
If the pump operates, but there is no flow, and if the pump is submerged and there are no kinks in the supply
tubing, lift the pump from the water. Remove supply tubing at the pump outlet and clean tubing inside and out if
necessary. Reset the pump in water (outlet side up) and once water begins to flow, re-attach the supply tubing.