Luxier FTF01-TB User manual

1FTF01 Rev.1 042018Luxier
Model Number:
FTF01-TB
FTF01-TC
Features:
- Brass and Zinc Alloy Construction
- Single Hole Installation
- Drip Free 40 mm Ceramic Cartridge
- Hand shower ow rate 1.8 gpm at 80 psi
- Tub spout ow rate 3.7 gpm at 20 psi
- Rough-in kit included
- Complies with:
IAPMO / UPC / cUPC
ADA
Freestanding Floor Mount Bathtub Filler
32”
38 1/8”
27 3/4”
43 1/16”
8 1/8”
5 1/2”
2”
4 5/16”
3 11/16”
1/2 NPT
* All Measurements are Approximate *

2FTF01 Rev.1 042018Luxier
Thank you for purchasing Luxier products. Please read the information below and keep this
installation guide for future reference. If you require assistance, please contact our customer service
department at 1-877-711-8828, Monday - Friday 9AM - 5PM Paci c Time or by email at
[email protected].
Limited Lifetime Warranty (For USA Only)
The manufacturer warrants this product to be leak and drip free during daily normal household use for as long as it is
owned by the original purchaser of this product. Please keep a copy of the original invoice as proof of purchase.
Should a malfunction occur within the warranty period, Luxier USA will, as its option, (1) repair or replace the defective
part(s) or product at no charge; (2) issue a refund of the purchase price paid for the product (Valid within 30 days from
the date of purchase); or (3) issue a credit to be applied against the purchase of a new Luxier product. Shipping/delivery
charges may apply and are in Luxier USA’s sole discretion.
This limited warranty shall not apply to goods which have been subject to accident, negligence, improper installation,
product abuse, product misuse, or use of cleaners containing abrasives, alcohol or other organic solvents, whether per-
formed by a contractor, service company, or yourself, are excluded from this warranty.
Our responsibility under this warranty is limited to only to replacement parts and no other costs. Luxier USA will not be
responsible for labor charges and/or damage incurred by installation, repair or replacement, nor for any indirect inciden-
tal or consequential damages, losses, injury or costs of any nature relating to this faucet. Except as provided by law, this
warranty is in lieu of and excludes all other warranties, conditions, and guarantees, whether expressed or implied, statu-
tory or otherwise, including without restriction those merchantability of  tness for use.
This limited warranty is non-transferable. This limited warranty only applies to products purchased and installed in the
United States. This limited warranty covers the original consumer purchase only and does not include business, commer-
cial or industrial use of this product. To obtain service under the Limited Warranty, please contact Luxier USA at
[email protected]. The Luxier USA Customer Care Department will determine whether to repair or replace your
product, issue a refund, or issue a credit.

3FTF01 Rev.1 042018Luxier
Important Points
• This installation guide is subject to change without notice, please contact us to request the most
updated version of this installation guide.
• This is a general installation guideline, actual installation may vary. Consult a professional if
necessary.
• Read and understand this instructions completely before installation.
• Please follow all local building and plumbing codes.
• Product drawings in this installation guide is for illustration purpose only. Actual product may vary
depends on model.
• Always take extra precautions and wear appropriate safety equipment when installing this
product.
• Wrap all threaded connections, except the aerator in the spout, with Te on (TPFE) tape. Always
wrap in a counterclockwise direction.
• When installing your new faucet,  rst hand tighten the water supply hoses then use a wrench to
give the compression nuts an additional (1/4) turn. Do not over tighten the compression nuts as it
will reduce the integrity of the sealed connection.
You may also need the following tools
1. Safety Glasses 5. Adjustable / Pipe Wrench
2. Teon (PTFE) Tape 6. Screwdriver
3. Plumber’s Putty and Caulking 7. Electric Drill
4. Pipe Cutter
Maintenance Guide
Please follow the cleaning material manufacturer’s instructions. Damage caused by improper
treatment will not be covered by product warranty. In addition, pay attention to the following points:
• Regular cleaning can prevent mineral build up on faucet spout.
• Carefully read the cleaner product label to ensure the cleaner is safe for use on the material.
• Test the cleaner on a small area before using on the entire surface.
• Use a mild detergent such as liquid dishwashing soap and warm water for cleaning.
• Do not use abrasive / harsh chemical when cleaning the  xture as they will damage and dull the
 nish.
• When using spray cleaners, spray  rst onto a soft cloth or sponge. Never spray directly onto the
faucet as droplets can enter openings and gaps and cause damage.
• After cleaning, rinse thoroughly with clean water to remove any cleaner residue.

4FTF01 Rev.1 042018Luxier
Installation
1. Connect hot and cold SUPPLY HOSES (5) into
the manifold using an adjustable wrench. Make
sure the connections are tight, use PTFE tape if
needed. Insert the RISER TUBE (1) over hot and
cold SUPPLY HOSES (5). Connect the RISER TUBE
(1) into base of the VALVE BODY (2) and tighten
fully.Slide the FLOOR MOUNTING FLANGE (3) onto
the RISER TUBE with the ange (4). Thread RISER
TUBE (4) into the bottom of RISER TUBE (1) and
fully tighten.
3. Make sure the oor is level in both directions.
Determine the distance from the nished wall to
the center of the oor water supply hose. Mark the
centerline. Drill a 2” (51mm) diameter hole for the
Hot and Cold water supply hoses.
Insert the water supply hoses through the hole and
place Tub Filler Assembly on the oor and check for
alignment.
Install SPOUT (1) into faucet body (2) tighten
Setscrew (3) with the supplied small hex wrench
supplied. Insert Handle (4) on the cartridge stem,
tighten the Setscrew (5) and install Cap (6) to the
Handle (4) .
HOT
COLD
hot inlet
cold inlet
hot water supply
cold water supply
5
5
1
2
4
3
1
1
3
4
5
6
2
Cartridge Stem
2
Level
BASE BOARD
2" Hole
FINISHED WALL LINE
COLD HOT
Top View
3

5FTF01 Rev.1 042018Luxier
Installation
1
2
4
4-1
4. With the Tub Filler Assembly aligned in the desired
position, mark each of the 4 mounting holes from the
Mounting Flange (1) on the oor.
4-1. Use a drill with 1/4” drill bit, drill the holes 1 3/4” deep
and insert the included Anchors (2). Make sure the Anchors
are ush with the nished oor.
5. Make sure both Hot and Cold water supply hoses pass
through the 2” mounting hole with at least 1 1/4” of the
hose in the oor space.
1/2 " Supplies Hoses
HotCold
1 1/4”
Finished Floor
Sub-Floor
HOT
COLD
5
pipe support
1
water pipe
water pipe
66. Apply PTFE tape to the threads of the T-Connector (1)
and the 2 Thread Adapters. Connect the 2 adapters to the
T-Connector (1) and tighten fully. Secure pipe below oor
to oor joist with pipe supports. Connect the 2 water supply
hoses to the T-Connector (1) and use an adjustable wrench
to tighten connections. Do not over tighten the connections.

6FTF01 Rev.1 042018Luxier
Installation
COLD
HOT
1
2
3
77. Hold the Tub Filler Assembly (1) in place and install
the four Mounting Screws (3). Check aligment and level
before fully tightening the Mounting Screws (3). After
tightening the screws slide the Escutcheon (2) down to
cover the ange.
8. Connect the Hand Shower Hose (5) to the Tub Filler.
Use an adjustable wrench to connect the Hand Shower
Hose (5) with hex nut end to the Tub Filler. (NOTE:
Make sure the rubber washers (1) are installed on both
end of the hose)
Hand tighten the Hand Shower Wand (6) to the Hand
Shower Hose (5). The Hand Shower Wand should be
placed in the Holder (3) when not in sue.
Remove the aerateor assembly (2) from the spout
and turn on water for couple of minutes and check all
connections for leaks. Move the Handle (4) throughout
the temperature range to ush out any debris in both
hot and cold water lines thoroughly.
Hex Fitting
1
5
2
3
4
1
6
8

7FTF01 Rev.1 042018Luxier
1
2
3
4
5
8
7
6
12
13
14
15
16
910 11
Parts
Operations
01. Aerator Assembly
02. Hand Shower Wand
03. Diverter Knob
04. Hand Shower Hose
05. Hot and Cold Water Supply Hose
06. T-Connector
07. Mounting Screws and Anchors
08. Escutcheon
09. Cartridge
10. Cartridge Locking Nut
11. Dome Cap
12. Cap, Setscrew and Hex Wrench
13. Handle
14. Diveter Cartridge
15. Hand Shower Connector Assembly
16. Setscrew
OFF
Front View
Diverter Knob
Side View
ON HOT COLD
To operate the tub ller simply move the
handle to the ON position to turn on the water.
Adjust the temperature by moving the handle
from side to side to set the desired water
temperature.
To operate the hand shower wand, remove
the hand shower from its holder and direct the
jets into the tub. Pull the diverter knob on the
faucet body. Push the diverter knob to direct
the water back to the spout.