LuxWay Triton User manual

Triton 4-Fold Bath Screen
• Instruction suitable for Right Side or Left Side Installation .
C0662-A00-01

• Check that the bath has been installed
correctly and that it is level. Please Note: All
product supplied without bath.
• Check that there is sucient space on the
bath for the product and that the screen
movement does not impact on other items
such as sinks and taps.
• Ensure the product is fitted to a non-porous
surface ie. tiled. Check that the wall surface
is flat.
• Unpack and check the product is complete
and undamaged, (refer to ‘Parts & Fittings
Supplied’ and ‘Loose Screws & Fittings
Supplied’ sections for details.
• Fixings are supplied for solid walls only.
Ensure that the correct fixings are used for
the wall type – if in doubt seek professional
advice.
• Ensure the area is clean, dry and dust free.
• Read the instructions in full.
• Have the correct tools available, (as shown
below, see ‘Tools Required’).
• Handle all glass with care - support on cardboard to avoid risk of breakage.
• This product is heavy and requires 2 people to carry and install it.
• Check walls first for hidden pipes and cables before drilling.
• All glass is toughened – it cannot be reworked or replaced by ordinary glass.
• Use safety eyewear when drilling.
• Use safety eyewear when handling glass.
• Keep all small parts away from children.
Safety
• Please notify the retailer immediately of any damage or faults. The manufacturer cannot be
held responsible for any installation costs that may arise from damaged or faulty product
being installed.
• Please dispose of all packaging with due regard to the environment.
Disclaimer
Before You Start
Tools Required (not supplied)
Fig.A.
Spirit Level Screwdriver Tape Measure
Scissors
Pencil Utility Knife
Silicone Gun & Sealant Power Drill Suitable Drill Bits
6mm
dia. *
3mm dia.
HSS
* Ensure drill bit
used is suitable
for wall surface

Parts & Fittings Supplied
We have taken great care to ensure that this product reaches you in perfect condition.
However should any parts be damaged or missing please contact your point of purchase.
This does not aect your statutory rights. In addition if you require replacement parts
your point of purchase will be happy to assist.
!
Keep small parts away from children
!
D2
D3
Bath Screen
Assembly
X1
Oversized Horizontal Seal
(Cut to suit)
X1
D1

D1 D2
D3
Wall Channel
X1
A
B
D
E
End
Moulding
X1
Seal
End Cap*
X2
End Cap
X1
* Left and Right Hand variants
Supplied (1 No. of each)
C
Hinge Screw
Cover Cap
X8

No.8 x 1½” Pan Head Pozi Screws
x4
Qty
A
Wall Plugs
x4
Qty
B
Screw Snap Cap Base
x4
Qty
C
No.8 x ⅜” Pan Head Pozi Screws
x4
Qty
D
(actual size)
(actual size)
(actual size)
(actual size)
Screw Snap Caps
x4
Qty
E
(actual size)
Loose Screws & Fittings Supplied

BATH
SIDE
OUTSIDE
FACE
Please Note:
Position Wall
Channel with
curved side facing
away from bath.
!
Tip:
When drilling tiles apply
masking tape to surface to stop
drill bit slipping.
*
Wall plugs supplied are for solid
walls only. Ensure correct wall
plug for wall type is used. If in
doubt seek professional advice.
!
Position wall channel on wall.
Ensure channel is vertically level
and does not overhang the bath.
!
B
Mark position
pre-drilled Wall
Channel holes
* dia. holes
with drill bit suitable
for wall surface
1.1
1.2*
1.3
A
Note:
Please process the wall jamb according
to the actual installed bathtub or shower base.
6mm
1
1

Slide Horizontal
Seal into position
Slide Horizontal
Seal into position
Tie end of seal
into tight knot
Horizontal Seal Preparation
i) ii)
Tip:
Apply a small amount of Silicone
Lubricant to the Horizontal Seal
to help slide into position.
*
2.3
2.2
2.1 2

Underside View
Horizontal
Seal
Bottom Hinge
Moulding
Plan View
3
4
Remove screw
as shown.
Push fit End
Cap Moulding,
fix using screw
removed in
previous step.
4.1
4.2
IMPORTANT NOTE:
Please ensure that Silicone
Sealant is apply fully between
Horizontal Seal and Bottom
Hinge Moulding as shown.
!
Bottom Hinge
Moulding
Horizontal Seal

5
5.3
5.2
5.1
Trim Horizontal
Seal overlap
Pull Seal Tight to
remove any slack.
Push fit End Cap
and Seal End
Caps.
Apply a small amount of
silicone sealant to End Cap
and Seal End Caps.

BATH
SIDE
OUTSIDE
FACE
7.1*
7.2
Inside View
7
Inside View
6
* 3mm dia. holes through
pre-drilled wall channel
holes using HSS drill bit
C
E
Please Note:
Ensure Horizontal Seal sits on top of bath.
D

Apply a small amount of Silicone
Grease from sachet (supplied) to
the hinge mouldings.
!
8.1
9
Inside View
8
Inside View
Inside View
Inside View
Push fit Hinge Screw Cover Caps.
!
9.1

150mm
Product Care:
Use a non abrasive cleaner.
Water marks may be
removed with a proprietary
limescale remover or
household vinegar.
*
11
Apply Silicone Sealant,
(not supplied).
!
10 Apply Silicone Sealant,
(not supplied).
!
Inside View