Lynn Electronics TEC MC-1500 User manual

-1- -2- -3-
1. Overview
2. Package Checklist
Before installing the , verify that the package contains
the following items:
1 x Media Converter
Power adapter (Check for area type)
Quick Installation Guide
3. Hardware Installation Procedure
The Media Converter is used to connect devices with
10/100/1000Base-T cable to ber-based Ethernet. The
Media Converter is enhanced with Link Fault Signaling.
STEP 1: Remove from packaging and connect the 12VDC
adapter to the power input on rear panel.
STEP 2 : Connect the Ethernet (RJ45) port to the networking
device. See the LNK/ACT LED to conrm if the
connection is established.
STEP 3 : Insert the SFP ( Not necessary for MC-1000SC-MM /
MC-1000SC-SM )
STEP 4 : Connect the ber cable to the ber port.
STEP 5 : See DIP switches on rear panel to enable/disable
the required features per application.
Quick Installation Guide
MC-1500 / MC-1000SC-MM / MC-1000SC-SM
Converter with 1x9 SC, SFP and RJ-45 Connectors
Converter with power jack and DIP switch
Front Panel View
Fiber Port
Fiber Port
LED Indicators
LED Indicators
RSV
RSV
Copper Port
Copper Port
10/100/1000
LNK/ACT
LFS
1000
1000
10/100/1000
LNK/ACT
LFS
1000
1000
RSV 1000
LFS
LNK/ACT
10/100/1000
1000
RSV 1000
LFS
LNK/ACT
10/100/1000
ON
OFF
PWR
12V DC
4. DIP Switches
DIP 1 Enables LFS function
DIP 2 Reserved
5. Location
Wall-mounted DIN-Rail-mounted
Rear Panel View with DIP Switches
12V DC
PWR
6. About RJ-45 Cables
When connecting your network devices, use at least
standard Category 3 eight-way cables for 10Base-T
The Media Converter can be placed on a desktop or horizontal
surface, it can be wall-mounted, or DIN-Rail mounted.

Application Cable Type Application
Converter
to
Converter
or
Network Adapter
Converter
End
Hub
Converter
End#1
Converter
End#2
Straight-through
Cable
Cross-over
Cable
Converter
to
Switch
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
-4- -5-
6400-131001
7. Link Fault Signaling (LFS)
The LFS LED will immediately light to indicate when a
cable has been severed or when some other cause of
disruption in service has occurred. The LFS function
connection status report.
Set LFS to ON for normal operational use. OFF
when installing cables or when testing the network
connection.
8. LED Indicators
This Converter has LED indicators located at the front
of the device. These have been designed to give easy
at-a-glance network status. Please see below for an
interpretation of their functions:
Unit LEDs
LED Condition Status
PWR On (Green) Converter is
receiving power
LFS On (Red)
Disruption of
connection in
segment
RSV Reserved, currently not in use
Fiber port
(1x9 SC/ SFP)
LNK/
ACT
On (Green)
Illuminated when
connectors are
attached
Blinking
(Green) through port
No valid link
established
RJ-45
Copper Port
1000
On (Green) Port operating at
1000Mbps
Port operating at
10/100Mbps
LNK/
ACT
On (Green)
Illuminated when
connectors are
attached
Blinking
(Green) through port
No valid link
established
Note: Automatic MDI/MDI-X selection on RJ-45 port
Please use the above table to determine the correct
cable for your serial devices.