Lynx greenMachine RFR 6000 User manual

greenMachine Quick
Reference
®
LYNXTechnik AG
www.lynx-technik.com
RFR 6000
Rack Frame for greenMachine
For optimum placement within an equipment room, greenMachine hardware can be
mounted in a 19” rack enclosure, the RFR6000 1RU rack frame option.
Each rack frame chassis (model: RFR 6000) can accommodate either or
pieces of greenMachine hardware and two power supplies (model: RPS 6120).
ONE greenMachine WITH ONE OR TWO POWER SUPPLIES
1
2
TWO greenMachines WITH ONE OR TWO POWER SUPPLIES
1
2

2
UNPACKING THE RFR 6000 RACK FRAME
We have included everything that is required for assembling the one or two
greenMachine setup.
1RU rack frame mounting tray
(RFR 6000)
19“ mounting brackets
(RML 6000)
Power Bridge
(RPB 6000)
1x 1RU rack frame mounting tray (RFR 6000)
2x 19“ mounting brackets (RML 6000)
1x power bridge (RPB 6000)
24x 3mm countersunk screws
4x 2.5mm countersunk screws
1x Quick Reference Guide
WHAT‘S IN THE BOX?
1x Warranty Card
1x Phillips screwdriver

3
ASSEMBLING YOUR RACK FRAME CHASSIS:
ONE greenMachine WITH ONE OR TWO POWER SUPPLIES
1
Step 1:
Step 2:
Assemble the 2x 19” mounting brackets (see page 6 ). MB
Turn the greenMachine hardware
upside down and remove the 4x
feet from the bottom. Set the four
screws aside for later use.
PS
Step 3: Place the rack frame mounting
tray over the bottom of the
hardware and align the holes
in the mounting tray with the
holes where the feet were.
Use the 4x 3 mm countersunk
screws to attach the mounting
tray to the hardware.
Note: DO NOT use the screws that were used to attach the feet.
Step 4: Turn the greenMachine hardware in rack frame the correct way up. Insert
the power supplies (see page 7).

4
2
TWO greenMachines WITH ONE OR TWO POWER SUPPLIES
Step 1: Assemble the 2x 19” mounting brackets (see page 6 ). MB
Turn the rack frame upside down and remove the power supply container
by unscrewing the 4x countersunk screws.
Set the power supply container and
screws to the side. These screws will be
used to attach the greenMachine to the
mounting tray.
Step 2:
Turn both the greenMachine modules upside down and place them next to
each other. Remove the 4x feet from the bottom of each of greenMachine.
Set the eight screws together with the feet aside for possible later use.
Step 3:
Place the rack frame mounting tray over both greenMachines and align the
holes in the mounting tray with the holes where the feet were. Use the 4x
3mm countersunk screws to attach the mounting tray to the hardware.
Step 4:

You are now ready to place the power supply
mounts to the 19” mounting brackets. Place the
two power supply mounts on the inside at the
end of each of the 19“ mounting brackets.
Remove the 4x screws on both sides of the power supply container.
Note: Set these eight
screws aside as they
will later be required
to attach the power
supply mounts to the
mounting brackets.
5
Take the power supply container and remove the
four screws on the top.
Note: These 4x countersunk screws are smaller
than the other screws and should not be used for
any other assembly in the rack frame.
Set these four screws aside for possible later use.
Step 5:
Step 6:
Step 7: Remove the power supply mounts.
Step 8:
Attach the power supply mounts to the rack frame mounting brackets with
the screws you removed from the sides of the power supply container.
Insert the power supplies (see page 7). PS Step 9:

6
HOW TO ASSEMBLE THE 19“ MOUNTING BRACKETS AND
ADJUST RACK POSITION
MB
RECESSED FLUSH PROTRUDED
Step 1: Choose your desired rack position.
Step 2: Use the 3mm screws to assemble the mounting brackets.
Use 4x screws for each mounting bracket.

7
HOW TO INSERT THE RPS 6120 POWER SUPPLIES INTO
THE RACK FRAME
PS
Insert the power supply that came with your greenMachine into the power
supply mount. The power cable needs to be next to the power supply as
shown below.
Note: The power supply should slide into the power supply mount without
resistance. If not, then remove the power supply and make sure the power
cord is positioned correctly.
Do not force the power supply into the mount.
Step 1: Unlock and slide over the power supply support clip.
Step 2:
Step 3: Slide over and push the power supply support clip foward to lock the
power supply.
Step 4: Repeat this procedure for the second power supply if applicable.

greenMachine
®
LYNXTechnik AG
www.lynx-technik.com © LYNXTechnik AG
SINGLE MODULE SETUP TWO MODULE SETUP
DEPTH 29.7cm (11.69“) 44.7cm (17.59“)
WIDTH Standard 19“ Rack Mount
HEIGHT 1RU
MODEL # RFR 6000
EAN # 4250479324466
INCLUDES
1x RFR 6000 rack frame mounting tray,
2x RML6000 mounting brackets, 1x RPB 6000 power bridge,
24x 3mm Screws, 4x 2.5mm Screws, 1x Phillips screwdriver
HOW TO USE THE RPB 6000 POWER BRIDGE FOR POWER
REDUNDANCY
PB
For full power redundancy with two greenMachines mounted in the rack
frame, use the RPB 6000 Power Bridge cable.
Connect a power supply to the DC 1 connector of
each greenMachine.
Connect the DC 2 connectors of both greenMachines
with the power bridge cable.
Step 1:
Step 2:
With this setup each power supply will
continue to power both greenMachines
even if one of the power supplies
should fail.
SPECIFICATIONS