Lynx R FR 5041 User manual

LYNXTechnik AG
Broadcast Television Equipment
© 2012 LYNX Technik AG all rights reserved
®
Reference Manual
R FR 5041
Series 5000 1RU 19” Rack Frame with Power Supply
(Suitable for up to four Series 5000 Modules)
Revision 1.3 –February 2012
Information in this document is subject to change without notice. No part of this document may be reproduced or
transmitted in any form or by any means, electronic or mechanical for any purpose, without express written permission of
LYNX Technik AG.
LYNX Technik AG may have patents, patent applications, trademarks, copyrights or other intellectual property rights
covering the subject matter in this document. Except as expressly written by LYNX Technik AG, the furnishing of this
document does not give you any license to patents, trademarks, copyrights or other intellectual property of LYNX Technik
AG or any of its affiliates.
LYNX Technik AG
Brunnenweg 3
D 64331 Weiterstadt
Germany
www.lynx-technik.com

R FR 5041 Reference Manual. Rev 1.3
Page 2 of 34
Contents
Contents ...............................................................................................................2
Warranty ...............................................................................................................4
Regulatory information ........................................................................................5
Europe........................................................................................................................................ 5
Declaration of Conformity ....................................................................................................... 5
USA............................................................................................................................................. 5
FCC 47 Part 15....................................................................................................................... 5
WARNING..............................................................................................................6
WARNUNG! ...........................................................................................................6
ESD Warning.............................................................................................................................. 7
Getting Started.....................................................................................................8
Packaging .................................................................................................................................. 8
Product Description.................................................................................................................. 8
Installation Instructions ......................................................................................9
Installations-Anweisung.......................................................................................9
Power Supply......................................................................................................10
Power Supply Alarm LED....................................................................................................... 10
Rack Controller ..................................................................................................11
Controller LED Indication....................................................................................................... 11
Module Installation ............................................................................................12
Rack Connections ..............................................................................................13
Rear Termination Panel.......................................................................................................... 13
AC Input and Fuses.............................................................................................................. 13
Rack Reference (Sync Connector)....................................................................................... 14
Redundant Power Input........................................................................................................ 14
Alarm Connection (Terminal Strip) ....................................................................................... 14
Alarm Function...................................................................................................................... 14
LAN Connection (Remote Control)....................................................................................... 15
Hot Swapping .....................................................................................................15
Power Supplies........................................................................................................................ 15
Power Supply Failure............................................................................................................ 15
CardModules............................................................................................................................ 15
System Cooling and Fans...................................................................................16
Fan Replacement..................................................................................................................... 16
Network Configuration .......................................................................................17
The Network Connection Manager........................................................................................ 17

R FR 5041 Reference Manual. Rev 1.3
Page 3 of 34
Configure IP Address.............................................................................................................. 19
Network Attaching the RFR 5041........................................................................................... 20
LYNX Desktop Controller Software ...................................................................21
System Requirements............................................................................................................. 21
Software Installation ............................................................................................................... 21
Starting the Controller Application ....................................................................................... 23
Software Updates ................................................................................................................. 23
Software Operation ............................................................................................24
Control System Layout.......................................................................................24
Device List ............................................................................................................................... 25
User Defined Device List ...................................................................................................... 25
Module Properties................................................................................................................... 27
New Control Window ............................................................................................................ 27
Module Title Area .................................................................................................................... 28
Locate Function .................................................................................................................... 28
Control Tabs ............................................................................................................................ 28
Power Supply Tab................................................................................................................. 28
Settings Tab.......................................................................................................................... 29
HotSync Backup...................................................................................................................... 29
Switching on HotSync........................................................................................................... 30
Options Tab .......................................................................................................................... 31
Events Tab............................................................................................................................ 32
Error Logging Area ................................................................................................................. 32
Service ...............................................................................................................34
Technical Support................................................................................................................... 34
Contact Information ...........................................................................................34

R FR 5041 Reference Manual. Rev 1.3
Page 4 of 34
Warranty
LYNX Technik AG warrants that the product will be free from defects in materials
and workmanship for a period of three (3) years from the date of shipment. If this
product proves defective during the warranty period, LYNX Technik AG at its
option will either repair the defective product without charge for parts and labor,
or will provide a replacement in exchange for the defective product.
In order to obtain service under this warranty, customer must notify LYNX
Technik of the defect before expiration of the warranty period and make suitable
arrangements for the performance of service. Customer shall be responsible for
packaging and shipping the defective product to the service center designated by
LYNX Technik, with shipping charges prepaid. LYNX Technik shall pay for the
return of the product to the customer if the shipment is within the country which
the LYNX Technik service center is located. Customer shall be responsible for
payment of all shipping charges, duties, taxes and any other charges for
products returned to any other locations.
This warranty shall not apply to any defect, failure, or damage caused by
improper use or improper or inadequate maintenance and care. LYNX Technik
shall not be obligated to furnish service under this warranty a) to repair damage
resulting from attempts by personnel other than LYNX Technik representatives to
install, repair or service the product; b) to repair damage resulting from improper
use or connection to incompatible equipment; c) to repair any damage or
malfunction caused by the use of non LYNX Technik supplies; or d) to service a
product which has been modified or integrated with other products when the
effect of such modification or integration increases the time or difficulty servicing
the product.
THIS WARRANTY IS GIVEN BY LYNX TECHNIK WITH RESPECT TO THIS
PRODUCT IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED.
LYNX TECHNIK AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. LYNX
TECHNIK`S RESPONISIBILITY TO REPAIR AND REPLACE DEFECTIVE
PRODUCTS IS THE SOLE AND EXCLUSIVE REMEDY PROVIDED TO THE
CUSTOMER FOR BREACH OF THIS WARRANTY. LYNX TECHNIK AND ITS
VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTIAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF
WHETHER LYNX TECHNIK OR THE VENDOR HAS ADVANCE NOTICE OF
THE POSSIBILITY OF SUCH DAMAGES.

R FR 5041 Reference Manual. Rev 1.3
Page 5 of 34
Regulatory information
Europe
Declaration of Conformity
USA
FCC 47 Part 15
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to the part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
We LYNX Technik AG
Brunnenweg 3
D-64331 Weiterstadt
Germany
Declare under our sole responsibility that the product
TYPE: R FR 5041
To which this declaration relates is in conformity with the following
standards (environments E1-E3):
EN 55103-1 /1996
EN 55103-2 /1996
EN 60950-1 /2006
Following the provisions of 89/336/EEC and 73/23/EEC directives.
Winfried Deckelmann
Weiterstadt, February 2012
Place and date of issue Legal Signature

R FR 5041 Reference Manual. Rev 1.3
Page 6 of 34
WARNING
Electrical supplies in excess of 50 (fifty) volts peak value are potentially hazardous or lethal. AC
supplies between 100 and 250 peak volts exist within the rack frame chassis when connected to
AC power. Only qualified personnel should service the rack frame assembly.
Removal of technical earth may render the equipment dangerous and intentional removal is
prohibited.
This unit has to be separated from mains by disconnecting the power supply cords.
This unit may have two power supplies and two power supply cords. Disconnect all power supply
cords before servicing to avoid electric shock.
DOUBLE POLE / NEUTRAL FUSING
After operation of the fuse, parts of equipment that remain energized might represent a hazard
during servicing.
For continued protection against risk of fire, replace only with same type and rating of fuse.
F1/F2: T2AH250V
Replacement AC fuses must be of the specified type and rating: F1/F2 = T2AH250V
The use of repaired fuses or shorting links has to be avoided.
WARNUNG! WARNING! CAUTION!
WARNUNG!
Wenn das Gerät an das Wechselstromnetz angeschlossen ist, treten innerhalb des Gerätes
Wechselspannungen zwischen 100 und 250 V auf, die potentiell gefährlich oder tödlich sein
können. Deshalb darf eine Reparatur und Instandhaltung nur von qualifiziertem Personal
durchgeführt werden.
Das Entfernen des Schutzleiters kann das Gerät in einen gefährlichen Zustand bringen,
vorsätzliches Entfernen des Schutzleiters ist verboten.
Das Gerät ist durch Abziehen beider Netzstecker vom Netz zu trennen.
Das Gerät kann 2 Netzgeräte mit 2 Netzkabeln haben. Vor Servicearbeiten müssen alle
Netzkabel abgezogen werden, um elektrischen Schlag zu vermeiden.
Die Netzzuführung ist 2-polig abgesichert. Nach Ausfall einer Sicherung können Teile der
Schaltung weiter unter Spannung bleiben und bei Servicearbeiten zu Gefahren führen.
Vor Servicearbeiten Stromversorgung unterbrechen und Teile vor Berührung prüfen.
Um Schutz gegen Feuer aufrechtzuerhalten, sind bei Sicherungswechsel nur Sicherungen des
gleichen Typs mit gleichen Daten zulässig. F1/F2 = T2AH250V

R FR 5041 Reference Manual. Rev 1.3
Page 7 of 34
ESD Warning
The internal electronics parts of this product are static sensitive. Please use caution and
use preventative measures to prevent static discharge or damage could result to
modules.
Electrostatic discharge (ESD) damage occurs when electronic assemblies or the
components are improperly handled and can result in complete or intermittent failure.
Do not handle the module unless using an ESD-preventative wrist strap and ensure that
it makes good skin contact. Connect the strap to any solid grounding source such as any
exposed metal on the rack chassis or any other unpainted metal surface.
Caution
Periodically check the resistance value of the antistatic strap. The measurement should
be between 1 and 10 Megohms.

R FR 5041 Reference Manual. Rev 1.3
Page 8 of 34
Getting Started
Packaging
The shipping carton and packaging materials provide protection for the rack frame during
transit. Please retain the shipping cartons in case subsequent shipping of the product
becomes necessary.
Product Description
The R FR 5041 is a high quality compact 1 RU high 19 inch rack frame enclosure for
LYNX Series 5000 CardModules, designed primarily for broadcast and professional
applications.
The rack frame can accept a maximum of 4 Series 5000 CardModules (any
combination*). Primary power supply and a fully integrated LAN port are also included
(LAN port is for remote control using the included LYNX Desktop Controller Software)
All CardModules and the Primary Power supply are installed and removed from the front.
Module rear connection panels are supplied with each CardModule and are mounted on
the rear of the rack as required. All CardModules and the power supply are hot
swappable.
*Note. Some Card Modules require a larger double height backplane (for I/O reasons)
which will occupy two pack slots. Please refer to individual module specifications for
details. These are typically the modules which currently have a double width backplane
when used with the RFR 5012 2RU rack frame.
The R FR 5041 features an integrated termination panel with connections for AC power
input, remote alarming, LAN control and a rack reference (sync). An external + 12VDC
power input connection is provided for optional external redundant power backup using a
brick power supply (Option R PS 5000)
The Rack frame has a hinged front cover providing easy access to all installed modules
and power supply which are hot swappable.
All electrical contacts inside the RFR 5041, CardModules and power supplies are gold
plated ensuring maximum reliability and protection from corrosion. Modules are
mechanically secured in place and will not shake loose with vibration (ideal for mobile
applications).
The R FR 5041 is one of the primary building blocks in the LYNX Series 5000
CardModule product line providing high quality, modularity and flexibility in a very small
form factor.

R FR 5041 Reference Manual. Rev 1.3
Page 9 of 34
!
!
!
!
!
!
Installation Instructions
The RFR 5041 is intended for operation in broadcast environments. The operation of the
equipment in environments which could produce excessive dust, moisture or extreme
temperatures requires special accommodation, such as:
Dust filters
Air conditioning
Avoidance of condensation
CAUTION!
The power cords must meet the safety requirements of the country where the rack
frame is used and has to be approved in this country, e.g.
CE-Mark in Europe
UL-listed in USA
CSA certified in Canada
CAUTION!
The power supply cords are used to disconnect the R FR 5041 from the AC mains
supply, ensure that the AC socket-outlets are located/installed near the equipment and
are easily accessible.
CAUTION!
The rack frame chassis is CLASS I EQUIPMENT. Before initial operation ensure that
protective earth is connected to the facility wiring and zero potential is established.
The functional earth connection at the rear termination panel is connected internally to
protective earth. If necessary, it may be used for potential equalization to other units.
Installations-Anweisung
Das Gerät R FR 5041 ist für Anwendungen in Fernsehstudios vorgesehen. Der Einsatz in
erhöhter staubiger und feuchter Umgebung oder außergewöhnlichen Temperaturen erfordert
besondere Maßnahmen wie
Klimatisierung
Staubfilter
Vermeiden von Kondenswasser.
ACHTUNG!
Die Netzkabel müssen den Sicherheits-Anforderungen in dem Land entsprechen in dem
das Gerät verwendet werden soll und in dem Land zugelassen sein, z.B.
CE-Zeichen in Europa
UL-gelistet in USA
CSA-Zulassung in Kanada
ACHTUNG!
Die Netzkabel dienen zur Trennung des Geräts vom Netz. Es ist sicherzustellen, dass
die Steckdosen für den Netzanschluss in der Nähe des Gerätes angebracht und zum
Trennen leicht zugänglich sind.
ACHTUNG!
Das Gerät ist nach der Schutzklasse I aufgebaut. Vor der ersten Inbetriebnahme muss
sichergestellt werden, dass der Schutzleiter mit dem zentralen Schutzleiter des
Gebäudes verbunden ist und spannungsfrei ist.
Der Erdanschlussbolzen an der Netzanschlussrückseite ist intern mit dem Schutzleiter
verbunden. Falls erforderlich, kann er für den Potentialausgleich mit anderen Geräten
verwendet werden.

R FR 5041 Reference Manual. Rev 1.3
Page 10 of 34
The rack frame is designed to fit into industry standard 19” equipment housing. The chassis will
occupy 1 RU of rack space. Opening the front cover will allow access to the 19” rack mounting
holes.
Airflow is from side to side, therefore care needs to be taken not to restrict the airflow through the
system. There are no ventilation holes in the top of bottom of the chassis, and no additional rack
space is required to accommodate vertical airflow or ventilation.
Power Supply
The R FR 5041 includes the primary power supply (an optional external power supply
(RPS 5000) can be used for redundancy which will provide a +12VDC input). Should a
power fault develop, the errors are alarmed in the following ways:
Via the LED located on the front of the Power Supply (visible through front cover)
Via a GPO alarm connection to the Termination Panel
Via the LYNX Desktop Controller connected to the LAN port (if used)
If the external redundant power supply (Option RPS 5000) is used then the system will
switch supplies automatically in the event of primary supply failure; with no interruption to
system operation.
The primary power supply is installed and removed from the front of the rack. The supply
locks itself firmly in place. The power supply can be released by pushing up the locking
clip and pulling on the handle above (see below)
Power Supply Alarm LED
LED Status
Description
GREEN
Normal Operation
YELLOW
Warning –High Temperature (over 55ºC)
RED FLASHING
Warning –Over Temperature (over 70ºC)
RED (Continuous)
Voltage Out of Range
OFF
Supply Failure (or AC power disconnected / AC fuses blown)
Alarm LED
Locking Clip
Handle