Lynxspring TSD7 User manual

200SM070 V1.3 Page 1 of 34
Touch Screen Display
User Guide

200SM070 V1.3 Page 2 of 34
Contents
Powering Up the Device..........................................................................................................................4
Set the Locale..........................................................................................................................................5
Connecting to a Source attached to a router over Wi-Fi –DHCP enabled.............................................6
Connecting to a Source attached over Wi-Fi –Static IP Enabled..........................................................22
Connecting to a Source over Ethernet –DHCP enabled.......................................................................28
Connecting to a Source over Ethernet –Static IP Enabled ...................................................................31
Note: Although screeenshots depict specific devices, be assured this system is designed to work
with most HTML5 webservering product. A list of such devices can be supplied upon request.

200SM070 V1.3 Page 3 of 34
Powering Up the Device
Once the installation of the display has been completed, a power source is connected, and the
preferred communication method is known and available, power up the tablet by doing the
following.
•Press the power button once quickly and release. The battery indicator should appear.
•Once the battery indicator is on screen, press the power button again, but hold the
button on.
•When the battery indicator disappears and a screen showing 4 x penguins appears,
release the power button.
•The unit will now power up.
•Any time while using the display, if you wish to power down or reboot the Source, press
and hold the power button until a popup display appears to give you these options.

200SM070 V1.3 Page 4 of 34
Set the Locale
1. Turn on the display. If for the first time, or there are no historical settings, you will see the
screen display as below. Pick the desired language. Time can also be set now if incorrect.
2. Untick the box if you do not want to see this dialog box again. Locale configuration is also
available in General Settings.

200SM070 V1.3 Page 5 of 34
Connecting to a Source attached to a router over Wi-Fi –DHCP enabled
1. If there are no historical settings, you will see this screen. Pick the desired connection type:
2. Select the network or source you wish to connect to from the list.

200SM070 V1.3 Page 6 of 34
3. Enter the password for the network or source and click connect:
4. If WPS is available on your network or Source, select the top right tab & select ‘Advanced’

200SM070 V1.3 Page 7 of 34
5. Select the WPS push button feature and enable WPS on your source at the same time:
6.The WPS system should now connect. Once connected, click ‘Next’

200SM070 V1.3 Page 8 of 34
7. The application will search and find all the Sources on the network:
8. Once search and discovery is complete, the Networks and Content Sources configuration
screen is shown:
•NOTE: Select the button (top left) or swipe from the left edge of the screen to
access the Menu.

200SM070 V1.3 Page 9 of 34
9. Various display settings can be configured by selecting General Settings:
10. General Settings
•Change the language.
•Change the Date / Time / Time Zone.
•Adjust the dimming behaviour,
To turn dimming off:
oSet the dimming value to 0 or blank

200SM070 V1.3 Page 10 of 34
oMake the brightness level and dimming level the same
NOTE: if you turn off dimming, the display may be affected by temporary image
ghosting if a static image is displayed for a prolonged period.
•Switch off source rotation enabled if more than 1 source has been configured. Default is
ON.
•Enable the password for the configuration screen.
•Add an NTP server if required.
•Configure how you view content served by saved sources. Detailed further in point 13
•To change the Date or Time, click ‘Adjust’.
•Deselect Automatic date & time and time zone, then adjust as required. Reselect Automatic
buttons once finished, then click next.
Enabling content browsers. By default, this is off. The content will be displayed by the Kiosk browser,
within Lynxspring APP. This gives a full browser experience in a full frame environment. If, however
your content design is such that you need or prefer to use a typical internet browser, the options
below are available.
a. Open content in Chrome Browser
b. Open content in Firefox Browser