LyvEco 9741B User manual

Dear valued customer,
Thank you for purchasing our floodlight. Before operating the floodlight, please read the following
instructions carefully and keep them in a safe place for future reference.
Proper Use
The floodlight is spray-protected, IP54 and for use outdoors.
The floodlight conforms with the appropriate European CE regulations.
ATTENTION
Please read the following instructions carefully, to ensure that the mounting operation will be carried out
in the correct way, and keep it for future reference .
The LED floodlight is waterproof IP54. Not suitable for use under harsh conditions.
CE conformity with the appropriate European directives
Model Rated
Power
Product
color
Power
factor Dimensions Remark
9741B 10W Black 0.5 89x125x30mm
External light protection class:IP54
Rated voltage:AC220-240V 50Hz
Color: 6500K
Beam angle:120º
Body material:Aluminium
9741W 10W White 0.5 89x125x30mm
9742B 20W Black 0.5 137x163x36mm
9744B 30W Black 0.9 186x201x45mm
9746B 50W Black 0.9 240x248x47mm
GENERAL SAFETY INSTRUCTIONS
• Never look directly into the LED light source. The light emitted can contain the colour blue.
• must always be placed at least 1m away from the surface being illuminated in particular,the power cable
must not be illuminated or come into contact with the metal housing maintain the specified minimum
clearances.
• must only be used on flat, stable surfaces.
• use only with a sufficiently protected AC220-240V installation.
• must not be used in rooms that represent an explosion hazard (e.g.cabinetmaker‘s workshop, painting
operation, or similar).
• must not be used in the immediate vicinity of flammable materials.
• must not be set up in the immediate vicinity of pools, fountains, ponds, or similar bodies of water.
• must not be immersed in water or other liquids.
• must not be operated with wet hands.
• must never be covered.
• must never be operated with an open housing, missing or damaged wiring compartment, or missing or
damaged lens.
• must never be sprayed or cleaned using a steam pressure cleaner since this can damage the insulation
and seals.
• must never be repaired by the user. Repairs must only be carried out by the manufacturer or an
authorized service representative.
INSTALLING
Installation may only be carried out by trained professionals according to the applicable installation
regulations. Contact a licensed electrician.
ATTENTION!! Before installation, the power supply must be disconnected and locked out.
LYVECO LED FLOODLIGHT
Model: 9741B, 9741W, 9742B, 9744B, 9746B
ANL_9741B_9741W_9742B_9744B_9746B.indd 1 2017-02-21 15:36:03

• Turn OFF power supply, ensure all required equipment and tools are present.
• Connect the pre-wired cable to the electrical supply, observing the correct polarity.
LIVE = BROWN
EARTH = GREEN/YELLOW
NEUTRAL = BLUE
• Check connections and fixings.
• Turn on Power and operate the floodlight as required.
Setting the Floodlight Direction
Loosen the screws on the sides of the mounting brackets, adjust the floodlight
direction, and then retighten all screws.
Range of mounting heights:under 20m
Suitability for use indoors.
If the external flexible cable or cord of this luminaire is damaged, it must be replaced by the manufacturer
or his service agent or a similar qualified person in order to avoid a hazard.
The light source of this luminaire is not replaceable; when the light source reaches its end of life the
whole luminaire shall be replaced.
Caution, risk of electric shock!
CLEANING
• Disconnect and lock out the power supply to the floodlight. Allow the floodlight to cool down
sufficiently!
• Clean with a dry or slightly moist, clean, lint-free cloth and a mild detergent if required. Do not use
cleaners that contain abrasives or solvents.
MAINTENANCE
• If the lens is damaged it must be replaced immediately.
• Clean any dirt from the housing or the lens immediately, since it could cause overheating.
Sensor Manual
The sensor should be installed by an electrician.
The lamp is equipped with a passive infra-red sensor. As soon as a person or a subject emitting heat
enters the range coverage during darkness, the lights switches on automatically .
The light stays on as long as there is some movement registered. It goes off when the defined time is
over. The built-in light sensor range coverage can be individually adjusted by the controls
Prior to Installation:
Please pay attention to the following points:
1. Do not fix the sensor too high, resulting in a too large range coverage, which would be followed by an
ANL_9741B_9741W_9742B_9744B_9746B.indd 2 2017-02-21 15:36:03

unwanted turning on and off. The best results are shown within the 1.8 to 2.3M height range.
2. The range-coverage is influenced by the temperature. It can be greater in winter than in summer.
3. Don’t install the sensor near trees and bushes. The movement of the plants can result in unwanted
turning on and off.
4. The sensor is more sensitive to sideway movements than forward and backward movements.
5. You can reduce the range coverage by mod-ifying the controls, or by covering some parts of the lens
Technical details:
Range coverage: 120°
Distance: 0,5-12M
Time setting: 2 sec to 600 sec
IP protection: IP54
Power: AC220-240V 50Hz
You find the time setter on the side of the sensor. (-) -- (+) It regulates the duration of the light
stays on. The sensor restarts counting every occasion there is a movement within its cover range.
Light intensity adjustable knob.
The main function is that adjust the sensors to work in different light intensity.
Position means that the sensors will start work when light intensity less than 100 lux.
Sensitivity:
The detection range can be set by adjusting the regulating dial“SENS”to the positions(-)—(+).
The position“MIN”means that the equipment detects objects in a distance of up to 0,5M. The
position“MAX”means that the equipment detects objects in a distance of max. 12M. The sensor
does not work in daylight.
WEEE-REQUIREMENTS OF DISPOSAL
In accordance with European regulations used electrical and electronics devices may no
longer be placed in the non recycling bin waste. The symbol of the waste bin on wheels
refers to the necessity of separate collection.
Please help with environmental protection and ensure the equipment is recycled correctly.
GUIDELINE 2012/19/EU of the EUROPEAN PARLIAMENT AND the COUNCIL of January 27th
2003 about electrical and electronics old devices.
Importer: Lyveco
Lyden House
Harlow CM20 2BS www.Lyveco.com
ANL_9741B_9741W_9742B_9744B_9746B.indd 3 2017-02-21 15:36:03