Lyyt FLB10C User manual

Errors and omissions excepted.
Copyright© 2015. LYYT
LYYT.CO.UK
PIR FLOOD LIGHT
These PIR flood lights are designed for easy installation to provide illumination for safety and security in
outdoor areas. Please read and keep the following instructions to aid setting up and get the best results
from your purchase.
Versions
Ref
Model
Power
Total luminous flux
Dimensions
Weight
GL469269
FLB10C
10W
800lm
185 x 113 x 113mm
0.74kg
GL469271
FLB20C
20W
1600lm
210 x 180 x 100mm
1.16kg
GL469273
FLB30C
30W
2400m
235 x 225 x 110mm
1.75kg
GL469275
FLB50C
50W
4000lm
250 x 280 x 130mm
2.52kg
Installation
LYYT flood lights with PIR can be attached to a wall or canopy using the integral bracket. The vertical
angle of the flood light may be tilted toward the area requiring illumination and then fixed by tightening
the hex screws at each side. The PIR section can be directed to the area required to detect movement
and fixed by tightening the single hand screw on the PIR pivot assembly.
Connection
The flood light is fitted with a mains lead and plug for easy connection.
For hard-wired connection, remove the plug and strip back the outer insulation to reveal 3 inner cores.
The colour coding follows EU mains wiring conventions as follows…
Brown = LIVE Blue = NEUTRAL Green/Yellow = EARTH
Connection to the PIR and LED driver are concealed within
the rear weatherproof housing.
Any internal connection and remote wiring should only be
carried out by a qualified electrical installer.
Note: THIS UNIT MUST BE EARTHED!

Errors and omissions excepted.
Copyright© 2015. LYYT
LYYT.CO.UK
PIR adjustment
On the underside of the PIR housing are 3 rotary controls for adjusting the PIR settings.
SENS is the setting for the PIR sensitivity to movement
TIME is the setting for the length of time the flood light will stay
on after movement is detected
LUX is the setting for the ambient light level below which the PIR
detector will be activated.
Once installed, connected and angle adjusted as required, set all 3 of the above settings to the minimum
level (anti-clockwise). If the flood light is on, it should go out within approximately 15 seconds.
Adjust the LUX setting up until the flood light switches on, staying on for 15 seconds again.
Adjust the SENS control to the halfway position and move around in the detection area to check that the
flood light is actuated. If not, the SENS setting will need to be increased. Check also that the PIR is not
too sensitive by moving around in an area or at a distance where triggering the flood light is not
required. If it is too sensitive, reduce the SENS setting.
Adjust the TIME setting to the length of time preferred for the flood to stay on after it has been
triggered by movement within the detection area.
Finally, the LUX setting should be adjusted so that the PIR detection is only active at the required level
of ambient light for the flood light to be in operation.
Turning the dial towards the “sun” symbol sets the PIR to operate in daylight.
Turning the dial towards the “moon” symbol sets the PIR to operate only during hours of darkness.
Adjustment between these two levels is variable and can be attuned to a preferred time of day.
Specifications
Power supply 230Vac, 50Hz
Beam angle 120°
Luminous efficacy 80lm/W
CCT 6000K
Approx. lifetime 30,000 hours
Switching cycle >15.000
PIR detection angle 180°
Max detection distance 12m @ 25°C
Ambient light setting 2lx –2000lx
Time setting 15 sec –6 min
Operating temperature -10°C to 40°C
Relative humidity <90%
Recommended height 1.8 - 2.5m
This product is classed as Electrical or Electronic equipment and should not be disposed with other household or
commercial waste at the end of its useful life. The goods must be disposed of according to your local council guidelines.