M-system R8-FS16N User manual

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9791 Rev.1 P. 1 / 6
INSTRUCTION MANUAL
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
DC voltage/current input module.......................................(1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVES
• The equipment must be mounted inside a panel.
• The actual installation environments such as panel con-
figurations, connected devices, connected wires, may af-
fect the protection level of this unit when it is integrated
in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures* to ensure the CE con-
formity.
* For example, installation of noise filters and clamp fil-
ters for the power source, input and output connected
to the unit, etc.
■GENERAL PRECAUTIONS
• Before you remove or mount the unit, turn off the power
supply and input signal for safety.
• Do not touch the connector while power is on. The unit
may have a malfunction due to static electricity etc.
• Switches on the side of the module can be set for mainte-
nance only while the power supply is off. Do not access
them while the power is supplied.
■ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■EXCITATION SUPPLY
• Input connector: Rated current 3A DC (rated current 3A
for internal fuse (slow blow fuse i2t (A2sec.) max. 5.04)
■AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
INSTALLATION
■HOW TO MOUNT THE MODULE ON DIN RAIL
• I/O Module
A
B
Confirm that the locking clamps of the I/O module are set.
Insert the module in parallel to the next one while aligning
the grooves of both modules (A & B in the above figure).
Maintain it perpendicularly to the rail.
More I/O modules can be added in the same manner.
DC VOLTAGE/CURRENT INPUT MODULE
(built-in excitation, 16 points, non-isolated) MODEL R8-FS16N

R8-FS16N
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9791 Rev.1 P. 2 / 6
• Protective Cover
Groove
Hook
The protective cover is to be attached over the connected I/O
module at the right end.
Align the hooks on the cover with the grooves of the module
and slide it straight until the hooks are latched.
When removing the cover, pull it out while squeezing the
hooks inward.
■HOW TO UNMOUNT THE MODULE ON DIN RAIL
Release the locking clamps and pull out straight the mod-
ule.
• Removing an intermediate module
Caution !
1) Be careful not to hurt your hand by pointed edges of the
internal bus connector.
2) I/O modules cannot hold tightly on the DIN rail by them-
selves without power/network module.
Secure them to the position if necessary by using DIN
rail end plates.

R8-FS16N
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9791 Rev.1 P. 3 / 6
COMPONENT IDENTIFICATION
Function Setting
DIP SW
Input Connector
Voltage / Current
DIP SW
8
7
6
5
4
3
2
1
SW1 SW2
On
■FRONT VIEW ■SIDE VIEW
RUN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
IN
12
39 40
On
1
16
On
1
16
Internal Bus Connector
Status Indicator LED
Input Status Indicator LEDs
Internal Bus Connector
VI
VI
■INDICATOR LED
ID OPERATION FUNCTION
Status OFF Stopping
Green ON Valid host communication
Green Blinking Reading/writing configuration
Red ON Setting error
Red Blinking Parameter error
Input
Status
OFF Input data in the range
Red Blinking Input data out of range
■MODULE ADDRESS: SW1
SW1-1 through 1-4 determine the tenth place digit, while
SW1-5 through 1-8 do the ones place digit of the module
address.
Address is selected between 0 to 24.
(Factory setting: 0)
MODULE ADDRESS
SW1
×10 1234
×1 5 6 7 8
0 OFF OFF OFF OFF
1 OFF OFF OFF ON
2 OFF OFF ON OFF
3 OFF OFF ON ON
4 OFF ON OFF OFF
5 OFF ON OFF ON
6 OFF ON ON OFF
7 OFF ON ON ON
8 ON OFF OFF OFF
9 ON OFF OFF ON
■OPERATING MODE
(*)Factory setting
• Terminator DIP SW: SW2-6
TERMINATOR SW SW2-6
Without (*) OFF
With ON
Note: Be sure to set unused SW2-1 through 2-5, 2-7 and 2-8 to
OFF.
• Voltage / Current DIP SW
For voltage input, set the switch OFF.
For current input set the switch ON.
Note: To configure the input, setting from configurator soft-
ware and the setting of this switch are required.

R8-FS16N
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9791 Rev.1 P. 4 / 6
■INPUT CONNECTOR ASSIGNMENT
39 40
12
PIN
No. ID FUNCTION
1In1 Input 1 (+)
2 Input 1 (−)
3In2 Input 2 (+)
4 Input 2 (−)
5In3 Input 3 (+)
6 Input 3 (−)
7In4 Input 4 (+)
8 Input 4 (−)
9In5 Input 5 (+)
10 Input 5 (−)
11 In6 Input 6 (+)
12 Input 6 (−)
13 In7 Input 7 (+)
14 Input 7 (−)
15 In8 Input 8 (+)
16 Input 8 (−)
17 In9 Input 9 (+)
18 Input 9 (−)
19 In10 Input 10 (+)
20 Input 10 (−)
21 In11 Input 11 (+)
22 Input 11 (−)
23 In12 Input 12 (+)
24 Input 12 (−)
25 In13 Input 13 (+)
26 Input 13 (−)
27 In14 Input 14 (+)
28 Input 14 (−)
29 In15 Input 15 (+)
30 Input 15 (−)
31 In16 Input 16 (+)
32 Input 16 (−)
33, 34,
35, 36 +24V Excitation supply 24V
37, 38,
39, 40 0V Excitation supply 0V
PC CONFIGURATOR
The following parameter items can be configured with PC Configurator Software (model: R8CFG).
Refer to the users manual of the software for detailed operations.
■CHANNEL INDIVIDUAL SETTING
PARAMETER SETTING RANGE DEFAULT SETTING
Input Range -10 to +10 (V DC) /
-20 to +20 (mA DC)
-10 to +10 (V DC)
Lower range value -10.00 to +10.00 (V) /
-20.00 to +20.00 (mA)
-10.00 (V)
Upper range value -10.00 to +10.00 (V) /
-20.00 to +20.00 (mA)
10.00 (V)
Fine zero adjustment -320.00 to +320.00 (%) 0.00 (%)
Fine gain adjustment -3.2000 to +3.2000 1.0000
Scaled range Zero -32000 to +32000 0
Scaled range Span -32000 to [phone]
■CHANNEL BATCH SETTING
PARAMETER SETTING RANGE DEFAULT SETTING
Loss of internal bus communication detection time 0.0 to 99.9 (sec.) 1.0 (sec.)
Moving average (ver. 2.00 or later) Disable/Enable (8 times) Disable
Note: Programming by the PC Configurator is available via the Power/Network Module.

R8-FS16N
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9791 Rev.1 P. 5 / 6
TERMINAL CONNECTIONS
Connect the unit as in the diagram below.
■EXTERNAL DIMENSIONS unit: mm (inch)
115(4.53)
6(.24)
7(.28)6(.24)7(.28)
[3(.12)] [4(.16)]
24(.94)[75(2.95)]
55(2.17)
DIN RAIL (35 mm wide)

R8-FS16N
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9791 Rev.1 P. 6 / 6
■CONNECTION DIAGRAM
INTERNAL POWER
INTERNAL BUS
EXC. SUPPLY
1
2
+
−
INPUT 1
3
4
+
−
INPUT 2
5
6
+
−
INPUT 3
7
8
+
−
INPUT 4
9
10
+
−
INPUT 5
11
12
+
−
INPUT 6
13
14
+
−
INPUT 7
15
16
+
−
INPUT 8
17
18
+
−
INPUT 9
19
20
+
−
INPUT 10
21
22
+
−
INPUT 11
23
24
+
−
INPUT 12
25
26
+
−
INPUT 13
27
28
+
−
INPUT 14
29
30
+
−
INPUT 15
31
32
+
−
INPUT 16
33
34
+24V
+24V
35
36
+24V
+24V
37
38
0V
0V
39
40
0V
0V
BUS CONNECTOR
WIRING INSTRUCTIONS
■MIL connector
Unit side connector: XG4A-4034 (Omron)
Recommended socket: XG5N-401 (Omron)*1
Recommended contact: XG5W-0231 (Omron)*1
Applicable wire size: AWG22, number of conductor 17, di-
ameter of conductor 0.16 mm
*1. Not included in the package. Refer to the specifications
of the product.