M-system R5 Series User manual

R5 Series Remote I/O
R5X PC CONFIGURATOR
Model: R5CON
Users Manual
http://www.m-system.co.jp/
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPA N
Te l: [phone] Fax: [phone]
E-mail: [e-mail]

2R5CON USERS MANUAL EM-9272 Rev.10
CONTENTS
1. GENERAL .............................................................................................3
1.1. FEATURES OF R5CON .....................................................................................................3
1.2. HARDWARE REQUIREMENTS.........................................................................................3
1.3. INSTALLING THE R5CON .................................................................................................3
1.4. UNINSTALLING THE R5CON ............................................................................................4
2. BASIC OPERATIONS ...........................................................................5
2.1. STARTING / QUITTING THE R5CON ................................................................................5
2.2. VIEW COMPONENTS AND FUNCTIONS .........................................................................6
2.3. CONNECTING/DISCONNECTING THE COMMUNICATION LINE....................................8
3. VIEWS & FUNCTIONS PARTICULAR TO MODULES .........................9
3.1. ANALOG I/O MODULE ......................................................................................................9
3.2. THERMOCOUPLE & RTD INPUT MODULE ................................................................... 10
3.3. CT & PT : AC CURRENT / VOLTAGE INPUT MODULE................................................... 11
3.4. DISCRETE INPUT MODULE ...........................................................................................12
3.5. DISCRETE OUTPUT MODULE .......................................................................................12
3.6. TOTALIZED PULSE I/O MODULE.................................................................................... 13
4. NETWORK MODULE..........................................................................14
4.1. ETHERNET SETTINGS ................................................................................................... 14
4.2. COMMUNICATION TIMEOUT .......................................................................................... 14
5. SAVING & READING PARAMETERS ................................................15
5.1. SAVING PARAMETERS ...................................................................................................15
5.2. READING PARAMETERS................................................................................................ 15

3R5CON USERS MANUAL EM-9272 Rev.10
1. GENERAL
In this manual, user is assumed that he/she is already familiar with operating Windows 7 or Windows 10 and terminology
used in these operating systems.
If you need to know about particular operation or terminology on Windows, please refer to manuals provided with the system.
1.1 FEATURES OF R5CON
The R5 Series are isolated, modular I/Os with open field networking capabilities, such for DeviceNet and Profibus. These
network modules can be directly connected to a Windows PC via PC Configurator Cable.
The R5CON software is used to help you program various parameters such as I/O scaling, zero/span adjustments to match
the users’ needs.
General functions of the R5CON are as follows:
■PARAMETERS CONFIGURATION FOR EACH CHANNEL
I/O range scaling and zero/span adjustments are available for each I/O module.
For temperature input modules, actual temperature range can be also programmed per each command.
For T/C input of the model R5(T)-TS (Ver 1.00 or higher), overrange limits (0% and 100% of the scaled range) can be applied.
When the input goes below 0% or above 100%, 0% and 100% data respectively are sent to the host PLC or PC.
■FILE MANAGING
The parameter configuration for each module can be saved as a file on the PC. Therefore, you can configure a set of param-
eters without actually connecting the R5x to your PC.
Reading (downloading) parameter files to the network module and each I/O module helps you to configure multiple modules
easily and accurately.
■MONITORING
You can check analog I/O data using configured data.
For discrete I/O modules, ON/OFF status of each channel can be monitored.
1.2 HARDWARE REQUIREMENTS
•DOS/V compatible PC with Windows 7 (32-bit, 64-bit) or Windows 10 (32-bit, 64-bit) appropriately installed.
•PC configurator cable, model MCN-CON or COP-US
1.3 INSTALLING THE R5CON
(1) Start up Windows.
(2) Go to M-System’s web site (http://www.m-system.co.jp). Download and save the R5CON archive in your PC’s local hard
disk.
(3) Confirm the size and version number of the downloaded archive (‘x’ in the file name as shown below). R5CON_Rx.exe or
R5CON_Rx.zip
(4) Double-click the file’s icon and locate ‘R5CON_Rx’ folder.
(5) Start up setup.exe in the folder and follow instructions on the screen. Now the R5CON program has been installed.
CAUTION !
If you have already the R5CON program installed in your PC, remove it following the procedure explained in “1.4
UNINSTALLING THE R5CON” before installing a new one.

4R5CON USERS MANUAL EM-9272 Rev.10
1.4 UNINSTALLING THE R5CON
(1) Click ‘Start’ on the task bar and choose Control Panel from Settings menu. (Double-click My Computer icon on the desktop
and choose Control Panel.)
>> Control Panel appears on the display.
(2) Double-click ‘Uninstall a program’ or ‘Program and feature’.
>> ‘Property’ dialog box of Programs and feature appears on the display.
(3) Choose ‘R5CON’ among the list of installed applications.
(4) Choose ‘Add/Remove’.
(5)‘Remove Programs From Your Computer’ dialog box appears on the display. Click OK.
>> All files installed with the R5CON are removed.
For Windows 10
(1) Click on START button at the lower left of the display to show a list of programs.
(2) Locate R5CON on the list, and right-click on it, then select Uninstall.

5R5CON USERS MANUAL EM-9272 Rev.10
2. BASIC OPERATIONS
Connect the R5 network module to the PC with PC configurator cable. Confirm the hardware connection in order to write the
setting data to the network module and each I/O module.
2.1 STARTING / QUITTING THE R5CON
Display images shown in this manual may change in detail when the software version is updated.
■STARTING THE R5CON
Press [Start] on the task bar and choose [R5CON] from [Program] menu. The main view appears on the screen as shown
below.
■QUITTING THE R5CON
Choose [Exit] from [File] menu to quit the program.
CAUTION !
Clicking [X] button at the right end of the title bar does not end the program.

6R5CON USERS MANUAL EM-9272 Rev.10
2.2 VIEW COMPONENTS AND FUNCTIONS
The R5CON view is composed of the menu bar at the top, the control panels below it and on the left, and the main frame
including various pop-up windows.
In this section, functions of menu bar and various buttons, and of each frame are explained.
■MENU BAR
Menu Submenu Function
File Open Reading the specified file and displaying its contents.
Save Saving the parameters as a file.
Exit Quitting the R5CON program.
Connect Connect Connecting to the communication line.
Disconnect Disconnecting from the communication line.
■CONTROL PANEL
[Card No.] list Shows the selectable card numbers. Click the arrow at the right to choose a card number in
order to switch the main frame from Overview to the detail view for the selected card (module).
<OverView> button Shows the hardware configuration. Click this button to switch the main frame back to Overview
from each card’s detail view.
<Upload> button Starts uploading I/O module’s information.
<Download> button Starts downloading I/O module’s information to the network module.
<Start> button Starts monitoring of the system.
<Stop> button Stops monitoring of the system.
<Setting> button Opens up the Com. card Settings view.
<Ethernet Setting> button Opens up the Ethernet Settings view for the R5-NE1 module. (Available only when the R5-NE1
module is connected.)

7R5CON USERS MANUAL EM-9272 Rev.10
■OVERVIEW
Item Function Selection Detail
No. Slot No. (1 to 16) ---- ----
In/Out Input or Output IN Input card (module)
OUT Output card (module)
IN/OUT 1 input / 1 re-transmitted output card (module)
Ver. No. Software version ---- ----
Input Type
Type of thermocouple and RTD ---- ----
Type I/O Card (Module) Type None No card mounted
Model No. One of the Model No. mounted
Ch. 1 Value
Ch. 2 Value
Analog I/O value for Ch. 1
Analog I/O value for Ch. 2
Decimal data Shows data sent to the host PLC.
Refer to the relevant descriptions in the data sheet of respective
modules. Scaled range if specified so.
Indicators Discrete I/O status Green OFF
Ch. 1 (left) to Ch. 16 (right) Red ON

8R5CON USERS MANUAL EM-9272 Rev.10
2.3 CONNECTING/DISCONNECTING THE COMMUNICATION LINE
■CONNECTING
Connecting the R5 network module to the communication line.
Choose [Connect] from [Connect] on the menu bar and the COM Port Setting window pops up on the screen.
Confirm that the power is supplied to the R5 modules and that the configurator jack of the R5 network module and the COM
port of the PC is firmly connected with the attached cable.
Choose an appropriate COM port No. (COM1 through COM8) and click OK.
With the communication line established, the communication status lamp turns to green and the COM port No. is shown.
• ➔➔➔
■DISCONNECTING
Choose [Disconnect] from [Connect] on the menu bar.

9R5CON USERS MANUAL EM-9272 Rev.10
3. VIEWS & FUNCTIONS PARTICULAR TO MODULES
3.1 ANALOG I/O MODULE
<Upload> button Uploading the current setting for the I/O module to the window.
<Download> button Downloading the setting on the current display to the R5 module.
Item Function Selectable Range
(must be used within this range)
Card No. Shows Slot No.
Card Type Shows I/O module hardware type
Version No. Shows firmware version No.
Zero Scale Enter 0% scaling value -32000 to 32000
Full Scale Enter 100% scaling value -32000 to 32000
Bias [Zero Adj.] Enter fine 0% adjustment value (bias) -320.00 to 320.00
Gain [Span Adj.] Enter fine 100% adjustment value (gain) -3.2000 to 3.2000
Zero Base Shows 0% input value in engineering unit Selected range
Full Base Shows 100% input value in engineering unit Selected range
Value Shows the current uploaded value of the scaled range.

10R5CON USERS MANUAL EM-9272 Rev.10
3.2 THERMOCOUPLE & RTD INPUT MODULE
<Upload> button Uploading the current setting for the I/O module to the window.
<Download> button Downloading the setting on the current display to the R5 module.
Item Function Selectable Range
(must be used within this range)
Card No. Shows Slot No.
Card Type Shows I/O module hardware type
Version No. Shows firmware version No.
Input Type Shows T/C or RTD input type setting
Burnout Shows the burnout type setting
Zero Scale Enter 0% scaling value -32000 to 32000
Full Scale Enter 100% scaling value -32000 to 32000
Bias [Zero Adj.] Enter fine 0% adjustment value (bias) -320.00 to 320.00
Gain [Span Adj.] Enter fine 100% adjustment value (gain) -3.2000 to 3.2000
Zero Base Enter 0% temperature. (factory setting = 0) As shown on the display
Full Base Enter 100% temperature. (factory setting = 0) As shown on the display
Value Shows the current uploaded temperature value.
Limit
(R5-TS V1.00 or higher)
Check the box to limit the input range within Zero Scale and Full Scale
when scaling is set. When no scaling is set and/or when the check box is
not selected, the input range is limited within -15 to +115%.
CAUTION !
Scaling is disabled when both Zero Scale is set to ‘0’ and Full Scale is set to ‘10000.’ The input module will send multiplied
raw data: with °C temperature unit, raw data is multiplied by 10 (e.g. 25.5°C is converted into 255), and with °F temperature
unit, the integer section of raw data is directly converted into the data (e.g. 135.4°F is converted into 135).

11R5CON USERS MANUAL EM-9272 Rev.10
3.3 CT & PT : AC CURRENT / VOLTAGE INPUT MODULE
<Upload> button Uploading the current setting for the I/O module to the window.
<Download> button Downloading the setting on the current display to the R5 module.
Item Function Selectable Range
(must be used within this range)
Card No. Shows Slot No.
Card Type Shows I/O module hardware type
Version No. Shows firmware version No.
Zero Scale Enter 0% scaling value -32000 to 32000
Full Scale Enter 100% scaling value -32000 to 32000
Bias [Zero Adj.] Enter fine 0% adjustment value (bias) -320.00 to 320.00
Gain [Span Adj.] Enter fine 100% adjustment value (gain) -3.2000 to 3.2000
Zero Base Enter 0% current (CT) or voltage (PT). Selected range
Full Base Enter 100% current (CT) or voltage (PT). Selected range
Value Shows the current uploaded value of the scaled range.

12R5CON USERS MANUAL EM-9272 Rev.10
3.4 DISCRETE INPUT MODULE
Item Function
Card No. Shows Slot No.
Card Type Shows I/O module hardware type
Version No. Shows I/O module’s firmware version No.
DI Data Shows current input data status
3.5 DISCRETE OUTPUT MODULE
Item Function
Card No. Shows Slot No.
Card Type Shows I/O module hardware type
Version No. Shows I/O module’s firmware version No.
DO Data Shows current output data status

13R5CON USERS MANUAL EM-9272 Rev.10
3.6 TOTALIZED PULSE I/O MODULE
<Upload> button Uploading the current setting for the I/O module to the window.
<Download> button Downloading the setting on the current display to the R5 module.
Item Function Selectable Range
(must be used within this range)
Card No. Shows Slot No.
Card Type Shows I/O module hardware type
Version No. Shows firmware version No.
Count Shows the present totalized count, 16 bits (decimal)
Span Enter the maximum count limit. 100 to 60000

14R5CON USERS MANUAL EM-9272 Rev.10
4. NETWORK MODULE
4.1 ETHERNET SETTINGS
With the Ethernet Interface Module (model: R5-NE1) connected, click <Ethernet Settings> button.
<Upload> button Reading the current setting from the R5 module and showing on the window.
<Download> button Writing the setting on the current display to the R5 module.
<Exit> button Close the window.
Item Function Selectable Range
(must be used within this range)
IP Address Enter IP Address 0 to 255 (integer)
Subnet Mask Enter Subnet Mask 0 to 255 (integer)
MAC Address Shows MAC Address
TCP Socket Enter TCP Socket Port No. to each port (1 thr. 4)
Modbus/TCP port number is 502.
502
Linger Enter time to close TCP Socket. (factory set to 1800)
TCP Socket closed after no communication (Set 1800 for 180.0 sec.) for
the preset time.
This function is selectable with the R5-NE1 Ver 0.04 or higher.
‘CNG’ is indicated on the screen when the version is lower than 0.04.
0 to 32767 (integer)
CAUTION !
Ethernet settings, once set, are enabled only after the power supply to the R5 network module is turned off and on.
4.2 COMMUNICATION TIMEOUT
Timeout means the time interval for the network module to recognize
interrupt communication when the network module terminates commu-
nication with the host PLC or PC, or the latter interrupt communication
with the former.
(1)Enter a value between 0 and 32767. In order to set to 30 seconds,
enter 300. (Factory setting = 3 seconds)
(2)Click [Download].

15R5CON USERS MANUAL EM-9272 Rev.10
5. SAVING & READING PARAMETERS
5.1 SAVING PARAMETERS
Parameters stored in I/O modules can be saved in a file.
(1)Open the Overview.
(2)Click [File] - [Save] on the menu bar.
(3)Specify a location and a file name to save.
5.2 READING PARAMETERS
Click [Open] in the pulled-down menu.
The PC Program reads the saved parameters but are not downloaded automatically to each module. <Download> on the
Overview.
(1)Click [File] - [Open].
(2)Locate the file and open it.
(3)Execute <Download> on the Overview.
(4)After changes have been applied, <Download> again.