M-system R3-BSW User manual

R3-BSW
P. 1 / 3EM-8357 Rev.7
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
INSTALLATION BASE
(free I/O address) MODEL R3-BSW
INSTRUCTION MANUAL
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
Base............................................................................... (1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVES
•The equipment must be mounted inside the instrument
panel of a metal enclosure.
•Theactualinstallationenvironmentssuchaspanelcon-
figurations, connected devices and connected wires may
affect the protection level of this unit when it is integrated
in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures to ensure CE conformity.
■GENERAL PRECAUTIONS
•Beforeyouremovethebaseormountit,turnoffthepower
supply for safety.
■ENVIRONMENT
•Indooruse
•Whenheavydustormetalparticlesarepresentintheair,
install the unit inside proper housing with sufficient ven-
tilation.
•Donotinstalltheunitwhereitissubjectedtocontinuous
vibration.Donotsubjecttheunittophysicalimpact.
•Environmentaltemperaturemustbewithin-10to+55°C
(14to131°F)withrelativehumiditywithin30to90%RH
in order to ensure adequate life span and operation.
■WIRING
•Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
•Do not bind these cables together with those in which
noisesarepresent.Donotinstalltheminthesameduct.
FRONT VIEW
I/O 1 I/O 2 I/O n
8
6
7
3
4
5
2
1
0
F
E
D
C
B
A
9
SW1
8
6
7
3
4
5
2
1
0
F
E
D
C
B
A
9
SW2
8
6
7
3
4
5
2
1
0
F
E
D
C
B
A
9
SWn –1
8
6
7
3
4
5
2
1
0
F
E
D
C
B
A
9
SWn
I/O MODULE ADDRESS
FreeI/Omoduleaddresscanbeassignedtoeachmodulepo-
sition using the rotary switch, within 1 to 16. Every module
can be mounted on any position.
Switch positions and addresses correspond to each other as
shown below:
I/Omoduleaddress Rotaryswitchposition
10
2 1
: :
n n – 1
: :
16 F
DONOTassignoneaddresstomorethanoneI/Omoduleto
ensure adequate operations and to prevent failures.
In case of power supply module, interface module, they op-
erate normally even address is conflicted.
Forapowersupplymodule,besuretoinstallintheright
end slot or left end slot for heat dissipation. In the case of
redundant power supply, consecutively install them in the
right end slot or left end slot.
ExampleforR3-BSW04
I/O module address
Rotary switch position
4312
Power
Supply
Module
Interface
Module
I/O
Module
I/O
Module
3201

R3-BSW
P. 2 / 3EM-8357 Rev.7
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
INSTALLATION
■VENTILATION SPACE
TheR3-BSWmustbemountedonaverticalpanel.Mount-
ing in any other angle will cause internal temperature to
rise, may shorten the product’s life expectation or deterio-
rate its performance.
30 (1.2)
50 (2)50 (2)
40 (1.6)
R3-BSW
Panel ceiling or wiring conduit (height ≤50 mm or 2 in.)
Panel bottom or wiring conduit (height ≤50 mm or 2 in.)
■WALL MOUNTING unit: mm (inch)
108 (4.25)
30
(1.18)
13.5 (.53)
26
(1.02)
30
(1.18)
n–M4 *
*n = Number of slots ×2
■DIN RAIL MOUNTING
Spring Loaded
DIN Rail Adaptor
DIN Rail
35mm wide
Set the base so that its
mounting adapter is at the
bottom.
Pull out the adaptor and
hung the upper hook at
the rear side of base on the
DINrail.
Push in the lower and re-
tract the adaptor, in keep-
ing pressing the base to the
DINrail.

R3-BSW
P. 3 / 3EM-8357 Rev.7
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EXTERNAL DIMENSIONS unit: mm (inch)
130 (5.12) 108 (4.25)
5 (.20)5.5 (.22)
30 (1.18)
4 (.16)
26.5
(1.04)
5 (.20)
DIN RAIL
(35 mm wide)
16.7
(.66)
120 (4.72)
13.5 (.53)
A
26 (1.02) 30 (1.18) n–4.5 (.28) dia. MTG HOLE
2 (.08) deep
*n = Number of slots x 2
30 (1.18)
*
8
6
7
3
4
5
2
1
0
F
E
D
C
B
A
9
SW1
8
6
7
3
4
5
2
1
0
F
E
D
C
B
A
9
SW2
8
6
7
3
4
5
2
1
0
F
E
D
C
B
A
9
SWn − 1
8
6
7
3
4
5
2
1
0
F
E
D
C
B
A
9
SWn
SIZE
MODEL A
R3-BSW04 112 (4.40)
R3-BSW06 168 (6.61)
R3-BSW08 224 (8.82)
R3-BSW10 280 (11.02)
R3-BSW12 336 (13.23)
R3-BSW14 392 (15.43)
R3-BSW16 448 (17.64)