M-system 18KBXH User manual

P. 1 / 2
EM-0493 Rev.1
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
18KBXH
BEFORE USE ....
Thank you for choosing M-System. Before use, check the
contents of the package you received.
If you have any problems or questions with the product,
please contact M-System's Sales Office or representatives.
n PACKAGE INCLUDES:
Standard rack...........................................................(1)
n MODEL NO.
Confirm that the model number described on the product is
exactly what you ordered.
n INSTRUCTION MANUAL
This manual describes necessary points of caution when you
use this product, installation, connection procedures.
POINTS OF CAUTION
nPOWER INPUT RATING & OPERATIONAL RANGE
•Locatethepowerinputratingmarkedontheproductand
confirm its operational range as indicated below:
24V DC rating: 24V ±10% , min. 1.3A
n ENVIRONMENT
•Indooruse
•When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
•Donotinstalltheunitwhereitissubjectedtocontinuous
vibration. Do not apply physical impact to the unit.
•Environmentaltemperature mustbe within-5 to+55°C
(23to131°F)withrelativehumiditywithin30to90%RH
in order to ensure adequate life span and operation.
•Besurethattheventilationslitsarenotcoveredwithcables,
etc.
n WIRING
•Donotinstallcables(powersupply,inputandoutput)close
to noise sources (relay drive cable,high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
n AND ....
•Theunitisdesignedtofunctionassoonaspowerissup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data sheet.
COMPONENT IDENTIFICATION
Specifications
(Side)
Body
MOUNTING REQUIREMENTS mm (inch)
101.6
（4.00）
255 (10.04)
273 (10.75)
*
Observe an appropriate wiring space over and below.
* 100 (3.94) for JIS standard
ANGLE BRACKET
4–M5 SCREW
TERMINAL CONNECTIONS
Connect the unit as in the diagram below.
nCONNECTION DIAGRAM
1
2
FG
3
CN1
CN2
＋
−
POWER
FIELD TERMINALS
Note : CN1 and CN2 are not available without connector.
STANDARD RACK MODEL
18KBX H
INSTRUCTION MANUAL

P. 2 / 2
EM-0493 Rev.1
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
18KBXH
CHECKING
1) Terminal wiring: Check that all cables are correctly con-
nected according to the connection diagram.
2) Power input voltage: Check voltage across terminals 1
(+)–2(–).Useapowersourceofripplelevel10%p-por
less.
3) Installation & environment: Check ambient temperature.
Also check that there are no excessive dust particles around.
Check that there is no vibration.
nCONNECTOR PIN ASSIGNMENT
•Fujitsu FCN type I/O connector
(Fujitsu FCN-365P40-AU)
Connector Pin Assignment
CN1: output 1 or input
CN2: output 2
PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT
A 1 ch. 1 +B1 ch. 1 –
A 2 ch. 2 +B2 ch. 2 –
A 3 ch. 3 +B3 ch. 3 –
A 4 ch. 4 +B4 ch. 4 –
A 5 ch. 5 +B5 ch. 5 –
A 6 ch. 6 +B6 ch. 6 –
A 7 ch. 7 +B7 ch. 7 –
A 8 ch. 8 +B8 ch. 8 –
A9 – A20, B9 – B20: Unused
Pin assignment is common to both CN1 and CN2.
• Toshiba DCS SAMP1 card use
• Toshiba DCS SAIN1, SAI06, SAO06 card use
Connector Pin Assignment
PIN NO. ASSIGNMENT
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
ch.1+
ch.1–
ch.2+
ch.2–
ch.3+
ch.3–
ch.4+
ch.4–
ch.5+
ch.5–
ch.6+
ch.6–
ch.7+
ch.7–
ch.8+
ch.8–
Pin assignment is common to both CN1 and CN2
The signal that is connected to the connector is the input signal
or the output signal 1.
Toshiba DCS SAMP1 uses Panasonic AXM220001. As con-
nector is discontinued, Omron XG4A-2034 is used as an
alternative.(Replacereceptacleside.)
12345678
CN1,CN2
12345678
Location
Output connector: HIF3BA-40PA-2.54DS (11)
CN1 :SAMP1
CN2 :SAMP1 for redundancy
18K-RACK LOCATION NO.
SAMP1 INPUT NO.
12345678
CN1,CN2
12345678
Location
I / O connector : Omron XG4A-2034
CN1 : SAIN1, SAI06, SAO06 (ch.1 –ch.8)
CN2
The input or output 1 is connected to the connector.
18K-RACK LOCATION NO.
SAIN1, SAI06, SAO06 INPUT or OUTPUT NO.
: SAIN1, SAI06, SAO06 (ch.1 –ch.8) for redundancy