Macab TVB-02 User manual

Catline amplifier TVB-02
120102 • 50119-ENG
Catline amplifier TVB-02
1. Connect a signal level meter to the incoming RF-cable and check
the levels. Of importance is that the atness is as good as possible (ie
the same level for low and high frequencies) and that the levels are
above the minimum input level (see table below). If the input levels are
too low it’s necessary to install a preamplifier.
2. Connect the RF signal to the amplier’s input port.
3. Connect the power cord to the power port.
4. Connect a TV-cable (TVB-01) to one of the outputs and adjust the
signal levels with input gain-, tilt- and output controls in min positions
(turned maximum to the left). Check that the levels are below maximum
output levels (see table below). If the levels are too high adjust with the
input gain control but not below minimum output level.
5. Make an overall cable loss calculation per output port (appr. 8 dB
per 10 meter of cable at 860 MHz).
6. Connect the signal level meter to the outputs and adjust the levels,
with respective output gain control, reecting the cable loss calculation.
7. Connect the patch cables (CAT5/CAT6) to the RJ-45 ports. Do not
take away the pre installed terminators from the ports that are not going
to be used.
8. Connect the TV-cables (TVB-01) to the RJ-45 outlets and check the
levels and the atness of the frequency band. If needed adjust the at-
ness with the “tilt” control.
9. Check the signal level in the TV-cables IEC connector and if neces-
sary ne adjust at the ampliers output gain controls. Normal signal
level to the TV-receiver is 60-80 dBµV (for analogue TV) and 50-70 dBµV
(for digital TV).
1. Test –20 dB
2. RF input
3. Adjustment - Gain input
4. Adjustment - Tilt input
5. Connection (x4) CAT5/6 cable
and terminator
6. Adjustment - Gain output (x4)
7. Connection power supply
Technical specifications
Part no – 380 00 02
Type – TVB-02
Frequency range MHz 47–862
Flatness dB ±0,75
Impedance
Input ohm 75
Output ohm 100
Gain 47-860MHz dB 35 (max)
Noise dB <8
Adjustable attenuation
Input dB 0–20
Output dB 0–20
Adjustable slope dB 0–18
Output level (DIN45004B) dBµV 122
Output level 42Ch CENELEC dBµV 107
Return loss
47–862 MHz dB >13
Isolation, port-port dB >20
Group delay ns <30
Testpoint dB –20
Power V DC 5 (via included adapter)
Power consumption mA 800
Temperature range °C –20 till +60
Screening – class B
Connectors
input –F-female
outputs –RJ-45 female
Dimensions (LxBxH) mm 200 x 41 x 38,2
12 3 4 5 6 7
Quick reference guide
Number of channels 42 10 2 Remarks
Min in-level, dBµV 63 63 63 at incoming cable
Min out-level, dBµV 87 87 87 incl. TVB-01 at output
Max out-level, dBµV 96 102 111 incl. TVB-01 at output

TV cable TVB-01 + Accessories
TV cable
Cable with built in transformer for converting from Ethernet (RJ-45
female) to coaxial (IEC-male). To be used for distribution of analo-
gue/digital TV via CAT-5/6 cable. TVB-01 is also perfect for distribu-
tion of IP-services over an existing coaxial cable.
Accessories
10”-panel
For installation of one amplier TVB-02 in a 10” cabinet.
Part no 380 00 04
Type 10”-panel
Height 46 mm
Length 10” (254 mm)
19”-panel
For installation of one or two ampliers TVB-02. A blind
panel is preinstalled if only one amplier is needed.
Part no 380 00 03
Type 19”-panel
Height: 46 mm
Length 19” (483 mm)
Technical specification
Part no – 380 00 01
Type – TVB-01
Frequency range MHz 47–862
Loss dB <5
Screening – class B
Connectors
outlet –RJ-45 male
TV – IEC-male
Length m 2
Terminator, 100 ohm RJ-45
For installation in amplier TVB-02. All not used ports have
to be terminated with a terminator.
Part no 380 00 05
Type terminator, 100 ohm RJ-45
Impedance ohm 100
Connector RJ-45, male