MAG THEATRON TDC Series User manual

Power amplifiers
TDC series
User manual
TDC-1200W
TDC-3200W
Models:
THEATRON

TDC series user manual rev 1.0
2
MAG THEATRON
Contents
Contents...................................................................................................................................................................................................2
Panel A. Dimensions ...........................................................................................................................................................................3
Panel B. Specifications ......................................................................................................................................................................4
Panel C. Front and rear panels.......................................................................................................................................................5
Panel D. Audio and Ethernet connection.................................................................................................................................6
Panel E. Menu structure....................................................................................................................................................................8
1. Safety instructions .........................................................................................................................................................................11
2. Regulatory information..............................................................................................................................................................12
3. TDC series .........................................................................................................................................................................................13
3.1. Introduction..............................................................................................................................................................................13
3.2. About the amplifier platform...........................................................................................................................................13
3.3. Unpacking and checking for shipping damage ......................................................................................................13
3.4. Disposal of the packing material ...................................................................................................................................13
4. Installation........................................................................................................................................................................................14
4.1. Cooling ........................................................................................................................................................................................14
4.2. Cleaning .....................................................................................................................................................................................14
5. Connections.....................................................................................................................................................................................16
5.1. Signal grounding ....................................................................................................................................................................16
5.2. Analog balanced input........................................................................................................................................................16
5.3. Analog unbalanced inputs ................................................................................................................................................16
5.4. Analog balanced output (through)...............................................................................................................................16
5.5. Loudspeaker connections .................................................................................................................................................16
5.6. Ethernet connection ............................................................................................................................................................16
6. Front panel....................................................................................................................................................................................... 17
6.1. Front LEDs................................................................................................................................................................................. 17
7.1. Menu diagram..........................................................................................................................................................................18
7.2. Event screen .............................................................................................................................................................................18
7.3. AMPLIFIER MENU.................................................................................................................................................................18
7.3.1. AMP SETTINGS submenu...........................................................................................................................................18
7.3.2. METERS submenu.........................................................................................................................................................18
7.3.3. INFO submenu.................................................................................................................................................................18
7.3.4. NETWORK submenu....................................................................................................................................................19
7.3.5. SIGNAL GENERATOR submenu..............................................................................................................................19
7.3.6. SERVICE submenu.........................................................................................................................................................19
7.3.7. PASSWORD submenu.................................................................................................................................................20
7.3.8. SYSTEM UNIT submenu ............................................................................................................................................20
7.4. CHANNEL MENU..................................................................................................................................................................20
7.4.1. VOLUME submenu. ......................................................................................................................................................20
7.4.2. SOURCE submenu........................................................................................................................................................20
7.4.3. PHASE submenu............................................................................................................................................................21
7.4.4. INPUT GAIN submenu.................................................................................................................................................21
7.4.5. SPEAKER PRESET submenu....................................................................................................................................21
7.4.6. PEQ BAND 1-6 submenus.........................................................................................................................................21
7.4.7. DELAY submenu..............................................................................................................................................................21
8.1. Default IP, user name and password........................................................................................................................... 22
8.2. Connecting to the Web UI ............................................................................................................................................... 22
8.3. Using the Web UI ................................................................................................................................................................. 22
8.3.1. Source window ............................................................................................................................................................... 23
8.3.2. Channel windows.......................................................................................................................................................... 23
8.3.3. Monitoring window......................................................................................................................................................24
8.3.4. Config window...............................................................................................................................................................24
9.1. About MAG Cinema macroprotocol.............................................................................................................................26
9.2. Sending the amplifier rack up for remote communication .............................................................................. 26
9.3. Macroprotocol syntaxis.....................................................................................................................................................26
9.4. Macroprotocol commands...............................................................................................................................................26
9.5. Finish markers. ....................................................................................................................................................................... 26
10.1. Product warranty................................................................................................................................................................28
10.2. Assistance..............................................................................................................................................................................28
CONTENTS

TDC series user manual rev 1.0
3
MAG THEATRON
Panel A. Dimensions
DIMENSIONS

TDC series user manual rev 1.0
4
MAG THEATRON
Panel B. Specifications
TDC-1200W TDC-3200W
Frequency range 20 Hz - 20 kHz 20 Hz - 20 kHz
Channel count 2 2
Nominal power, per channel,
4 Ohm load 600 W 1600 W
Nominal power, per channel,
8 Ohm load 400 W 1100 W
Nominal power, two channels
bridged, 8 Ohm load 1200 W 3200 W
Nominal power, two channels
bridged, 16 Ohm load 600 W 1600 W
Amplifier
DSPaudiocontrols 6-bandparametric EQ,volume,polarity, delay
DSPutility controls Power saving mode, power-up mode
Inputsensitivity +5dBu +7dBu
Maximum input level +20dBu
Inputimpedance 18kOhm unbal., 36 kOhmbal.
Crosstalkseparation 85 dB @ 1 kHz
THD <0,5% from 0,1 W to full power (typical <0,01%)
Power consumption, 1/8 of max
output power @ 8 Ohm 220 VA 600 VA
Damping factor, 8 Ohm > 10000 @ 100 Hz > 500 @ 100 Hz
S/N ratio 100 dB
Connectors 2x RCA unbal. input, 2x XLR female bal. input, 2x XLR male bal. output,
4-pin Phoenix speaker terminal, RJ-45 Ethernet
Dimensions (W×H×D) 486 x 88 x 294 mm, 2U
Netweight 5,25 kg 5,9 kg
SPECIFICATION

TDC series user manual rev 1.0
5
MAG THEATRON
Panel C. Front and rear panels
A. Control wheel.
B. Channel protect LED.
C. Channel limiter LED.
D. Channel signal LED.
E. Channel edit mode LED.
F. Channel 1 selection button.
G. Channel 2 selection button.
1. Mains switch.
2. Mains plug.
3. Output Phoenix connector.
4. Channel 1 unbalanced RCA input.
5. Channel 2 unbalanced RCA input.
6. Channel 1 balanced XLR female input
connector.
7. Channel 2 balanced XLR female input
connector.
8. Ethernet RJ-45 connector.
9. Channel 1 balanced XLR male through
connector.
10. Channel 2 balanced XLR male through
connector.
A
B C D E BCD
E
FG
1 4 5 8
2 3 6 7 9 10
FRONT AND REAR PANELS
BALANCEDTHROUGH

TDC series user manual rev 1.0
6
MAG THEATRON
Panel D. Audio and Ethernet connection
Input connectors, unbalanced
+ Ch1 + Ch2
shield Ch1 shield Ch2
Input connectors, balanced
+ -
shield
2
3
1
Through connectors, balanced
+ -
shield
2
3
1
AUDIO AND ETHERNET CONNECTION

TDC series user manual rev 1.0
7
MAG THEATRON
ETH port in 1ETH TX+ GREEN/WHITE
2ETH TX- GREEN
3 ETH RX+ ORANGE/WHITE
4 not connected BLUE
5 not connected BLUE/WHITE
6 ETH RX- ORANGE
7 not connected BROWN/WHITE
8 not connected BROWN
568A 568B
Loudspeaker connection, bridged mode
Loudspeaker connection, stereo mode
AUDIO AND ETHERNET CONNECTION

TDC series user manual rev 1.0
8
MAG THEATRON
Panel E. Menu structure
PC Connected …
PC Connected … Connected … (f,I,m,s)
Firmware update
Password#1
Ch N- DC3000 password protected
Prot- 5 sec
Sleep- Ch1- Name
St.By- Ch2- Name
Mute- 2
SysMute - UnMute
SysStBy - ON
common selector for AES / EBU pairs AES\EBU Analog
3d7.1 a7.1
1d5.1 a5.1
Password#1 Mode - d7.1 [V] d4.0 a4.0
d2.1 a2.1
d2.0 a2.0
1 - Master Volume Range dB Shift
MasterVol. 3.6 0 - 4 100 - 20 2 dB
min_ _max 4.1 - 10 20,5 - 0 0,33 dB
2
Password#1
1 Ch._1- UnMuted
2 3 Ch._2- UnMuted
3Password#1 StandBy - OFF
4EnergySave - OFF
5 4
6Password#1
7
8Load - Yes
9Password#2 Store - Yes Temp. M1 39 C
10 Temp. M2 39 C
Type filtr IMP.1ch- 4 Ohm
Switch Peak
IMP.2ch- 4 Ohm
ON Low Shelf
Go To 1 OFF High Shelf +6db\-6db steep 0.5db
5MODEL -DC 1200
Password#1 ON Peak Gn +6,0 Unit -Name
Fq 7127 Qu 0,5
1Ch- Name
2Ch- Name
Amplifier_ID :001
20Hz-20159Hz for Peak 0.5db - 12db steep 0.5 db FirmHard :001:001
steep 1/12 okt for Shelf 0.5db – 2.8db steep 0.1 db Prot.Ver. :001
S\N
Code-
Ext.mod. NET:AES
NET
AES AES\EBU module
1----
2
IP_addr P:08234
1Subnet mask /24
2
3 Gateway STATIC
4
5
Password#1 AMP_ID - [01] Radge -0 - 31
ID_Edit - Yes
Net_Setup - Yes
Radge -All 4 oktet
Password#1
IP_Edit - Yes
Password#1 MASK_Edit - Yes
Radge -1 - 31
Password#1 Yes
Radge -All 4 oktet
5 Signal generator
Gn -23dB Sinus Type
80 Noise
Sinus
80; 1000; 8000
20
ON L ;R ;C ;LFE;
Yes LRC;RRC;LSS;RSS
ON Ch 1 U.Name < >
Go To 1
>000000< OPEN
MID
---
password protection enabled
AllCopy 2 to 1 ?
AllCopy 1 to 2 ?
SOURCE ≠
!1≠2! Different
Copy 1 to 2 ?
Copy 2 to 1 ?
-----Exit----
Gateway address
if the parameters do not match
Copy 1 to 2 ?
designation
result of parameter comparison
= compared
≠not compared
Gateway_Edit
<<SOURCE>> :
Analog_1
designation
<<___DSP MENU___>>
6- Password
[OPEN] -
Input Password
Gatewa address editor
Default ethernet settings
192.168.000.007
STATIC
192.168.000.001
255.255.255.000\24
Additional options
Turning the device ON with wheel pressed will reset Ethernet settings to
default. Device will not be available for 30 seconds.
IP address network
Subnet mask network
Type of ip address
optional for DSP menu(5-10)
Frequency(Hz) sinus
Frequency
Range - OFF; (-40dB - 0dB)
Generator gain
IP address network
Port (computer networking)
Subnet mask network
Network prefix size
Gateway address
Type of ip address
192.168.000.001
4.3
4.2
Contrast set -
EventScreen -
Name Editor -
CinemaMode -
----Exit---
Edit username Channel 1
Edit username Channel 2
Edit the unit name
Selection Name
Standart names(3
Selection Name
Range - (19 -25)
if present Ethernet module
4- Network
Amplifier identifier editor
4.1
Exit > Save!
Amplifier menu
16 Ohm - 1 Ohm
0 C - 100 C
Factory name of the amplifier
Not present module
192.168.000.007
255.255.255.000
5- Service
User name of the amplifier
User name of the chanell №1
User name of the chanell №2
Amplifier identifier
Version - Firmware : Hardware
IP address editor
Subnet mask editor
Protocol version
Product serial number
Amplifier menu
AMP SETTING
MASTER VOLUME
<<AMPLIFIER MENU>>
METERS
Activated by pressing or rotating the wheel
Display Contrast
Events Screen
Range - (ON-OFF)
Secret product code
External modules
Ethernet module
2 - Amplifier setting
ON ----- OFF
Amplifier energy save
3- Meters
UnMuted ----- Muted
ON ----- OFF
Temperature
Amplifier standby
Master volume
0 - 10 steep 0.1
100dB - 0dB
SOURCE
-80db\+6db steep 1db
Channel input gain
Analog_1
Input selector
------Normal------
------Invert------
Phase invertor
----EXIT----
Analog_2
AES/EBU_1_1
AES/EBU_1_2
AES/EBU_2_1
AES/EBU_2_2
AES/EBU_3_1
AES/EBU_3_2
AES/EBU_4_1
AES/EBU_4_2
------Normal------
Input Gain
>____________0dB
DSP menu
Preset № 1 v
Chanell impedance
Frequency
Gain
Quality
3- Info
010203040506
3.1- Continued Info
continued if present Ethernet module
INFO
NETWORK
SIGNAL GENERATOR
Parametrick Eqalizer
quantity - 6 pieces
AES/EBU_4_2
----EXIT----
Pair number 4
MAG-CINEMA d5.1
communication screen
Sound system
Start screen
MAG-CINEMA
Event Screen
Command Cinema menu
Activated while "CinemaMode" is active for first amplifier group
Cinema Group Mute
UnMute ----- Mute
Cinema Group Standby
ON ----- StBy
Cinema sound system
if present AES\EBU module
second press to return to the AMPLIFIER menu
simultaneous pressing the button # 1 and the # 2 button for controlling two channels
Turn to display the AMPLIFY menu,
or use to edit the parameters.
for DSP menu if not compared
Service
PASSWORD
MASTER VOLUME
Chanell muted
PEQ BAND 6
Activated by pressing button 1 or button 2
<<___DSP MENU___>>
SOURCE
PHASE
INPUT GAIN
SPEAKER PRESET
PEQ BAND 1
PEQ BAND 2
PEQ BAND 3
PEQ BAND 4
PEQ BAND 5
<<SOURCE>>
Analog_1
Name: SCR-315
PhaseInvert
Name Ethernet module
Mag-Audio
Additional options
Turning the device on wheel and button №1 or №2 will enter the HARDWARE
update mode. If update process will not be activated in 15 seconds, device will
reboot normally. In HARDWARE update mode yellow LED №1 indicates active
HARDWARE update mode (always lit). Yellow LED №2 indicates update
process (flashing when data stream is active). No messages on display.
Speaker preset base
Select Speaker preset
quantity - 50 pieces
Select Speaker preset
DSP menu for channel №2
The second DSP menu is
completely identical to
the first
The second DSP menu is
completely identical to
the first
Input selector
Analog_1
Analog_2
AES/EBU_1_1
AES/EBU_1_2
AES/EBU_2_1
AES/EBU_2_2
AES/EBU_3_1
AES/EBU_3_2
AES/EBU_4_1
Pair number 1
Pair number 2
Pair number 3
first press to call the DSP less than channel number 2
first press to call the DSP less than channel number 1
1513erD1518
three-level password protection
first level functions are available
all functions are available
there is a connection to the cinema equipment
there is a connection to the PC
ordinary message
alarm message
sleep message
standby mode message
mute sound mode message
event message
Copy menu for both channels
Both channels are identical
Both channels are not identical
Copy channel 1 to channel 2
Copy channel 2 to channel 1
Exit
Copy all six EQ bands from channel 1 to channel 2
Copy all six EQ bands from channel 2 to channel 1
Press key 1+ key2 for DSP menu
DSP menu for channel №1
12Rotate or press
Wheel
MENU STRUCTURE

TDC series user manual rev 1.0
9
MAG THEATRON
PC Connected …
PC Connected … Connected … (f,I,m,s)
Firmware update
Password#1
Ch N- DC3000 password protected
Prot- 5 sec
Sleep- Ch1- Name
St.By- Ch2- Name
Mute- 2
SysMute - UnMute
SysStBy - ON
common selector for AES / EBU pairs AES\EBU Analog
3d7.1 a7.1
1d5.1 a5.1
Password#1 Mode - d7.1 [V] d4.0 a4.0
d2.1 a2.1
d2.0 a2.0
1 - Master Volume Range dB Shift
MasterVol. 3.6 0 - 4 100 - 20 2 dB
min_ _max 4.1 - 10 20,5 - 0 0,33 dB
2
Password#1
1 Ch._1- UnMuted
2 3 Ch._2- UnMuted
3Password#1 StandBy - OFF
4EnergySave - OFF
5 4
6Password#1
7
8Load - Yes
9Password#2 Store - Yes Temp. M1 39 C
10 Temp. M2 39 C
Type filtr IMP.1ch- 4 Ohm
Switch Peak
IMP.2ch- 4 Ohm
ON Low Shelf
Go To 1 OFF High Shelf +6db\-6db steep 0.5db
5MODEL -DC 1200
Password#1 ON Peak Gn +6,0 Unit -Name
Fq 7127 Qu 0,5
1Ch- Name
2Ch- Name
Amplifier_ID :001
20Hz-20159Hz for Peak 0.5db - 12db steep 0.5 db FirmHard :001:001
steep 1/12 okt for Shelf 0.5db – 2.8db steep 0.1 db Prot.Ver. :001
S\N
Code-
Ext.mod. NET:AES
NET
AES AES\EBU module
1----
2
IP_addr P:08234
1Subnet mask /24
2
3 Gateway STATIC
4
5
Password#1 AMP_ID - [01] Radge -0 - 31
ID_Edit - Yes
Net_Setup - Yes
Radge -All 4 oktet
Password#1
IP_Edit - Yes
Password#1 MASK_Edit - Yes
Radge -1 - 31
Password#1 Yes
Radge -All 4 oktet
5 Signal generator
Gn -23dB Sinus Type
80 Noise
Sinus
80; 1000; 8000
20
ON L ;R ;C ;LFE;
Yes LRC;RRC;LSS;RSS
ON Ch 1 U.Name < >
Go To 1
>000000< OPEN
MID
---
password protection enabled
AllCopy 2 to 1 ?
AllCopy 1 to 2 ?
SOURCE ≠
!1≠2! Different
Copy 1 to 2 ?
Copy 2 to 1 ?
-----Exit----
Gateway address
if the parameters do not match
Copy 1 to 2 ?
designation
result of parameter comparison
= compared
≠not compared
Gateway_Edit
<<SOURCE>> :
Analog_1
designation
<<___DSP MENU___>>
6- Password
[OPEN] -
Input Password
Gatewa address editor
Default ethernet settings
192.168.000.007
STATIC
192.168.000.001
255.255.255.000\24
Additional options
Turning the device ON with wheel pressed will reset Ethernet settings to
default. Device will not be available for 30 seconds.
IP address network
Subnet mask network
Type of ip address
optional for DSP menu(5-10)
Frequency(Hz) sinus
Frequency
Range - OFF; (-40dB - 0dB)
Generator gain
IP address network
Port (computer networking)
Subnet mask network
Network prefix size
Gateway address
Type of ip address
192.168.000.001
4.3
4.2
Contrast set -
EventScreen -
Name Editor -
CinemaMode -
----Exit---
Edit username Channel 1
Edit username Channel 2
Edit the unit name
Selection Name
Standart names(3
Selection Name
Range - (19 -25)
if present Ethernet module
4- Network
Amplifier identifier editor
4.1
Exit > Save!
Amplifier menu
16 Ohm - 1 Ohm
0 C - 100 C
Factory name of the amplifier
Not present module
192.168.000.007
255.255.255.000
5- Service
User name of the amplifier
User name of the chanell №1
User name of the chanell №2
Amplifier identifier
Version - Firmware : Hardware
IP address editor
Subnet mask editor
Protocol version
Product serial number
Amplifier menu
AMP SETTING
MASTER VOLUME
<<AMPLIFIER MENU>>
METERS
Activated by pressing or rotating the wheel
Display Contrast
Events Screen
Range - (ON-OFF)
Secret product code
External modules
Ethernet module
2 - Amplifier setting
ON ----- OFF
Amplifier energy save
3- Meters
UnMuted ----- Muted
ON ----- OFF
Temperature
Amplifier standby
Master volume
0 - 10 steep 0.1
100dB - 0dB
SOURCE
-80db\+6db steep 1db
Channel input gain
Analog_1
Input selector
------Normal------
------Invert------
Phase invertor
----EXIT----
Analog_2
AES/EBU_1_1
AES/EBU_1_2
AES/EBU_2_1
AES/EBU_2_2
AES/EBU_3_1
AES/EBU_3_2
AES/EBU_4_1
AES/EBU_4_2
------Normal------
Input Gain
>____________0dB
DSP menu
Preset № 1 v
Chanell impedance
Frequency
Gain
Quality
3- Info
010203040506
3.1- Continued Info
continued if present Ethernet module
INFO
NETWORK
SIGNAL GENERATOR
Parametrick Eqalizer
quantity - 6 pieces
AES/EBU_4_2
----EXIT----
Pair number 4
MAG-CINEMA d5.1
communication screen
Sound system
Start screen
MAG-CINEMA
Event Screen
Command Cinema menu
Activated while "CinemaMode" is active for first amplifier group
Cinema Group Mute
UnMute ----- Mute
Cinema Group Standby
ON ----- StBy
Cinema sound system
if present AES\EBU module
second press to return to the AMPLIFIER menu
simultaneous pressing the button # 1 and the # 2 button for controlling two channels
Turn to display the AMPLIFY menu,
or use to edit the parameters.
for DSP menu if not compared
Service
PASSWORD
MASTER VOLUME
Chanell muted
PEQ BAND 6
Activated by pressing button 1 or button 2
<<___DSP MENU___>>
SOURCE
PHASE
INPUT GAIN
SPEAKER PRESET
PEQ BAND 1
PEQ BAND 2
PEQ BAND 3
PEQ BAND 4
PEQ BAND 5
<<SOURCE>>
Analog_1
Name: SCR-315
PhaseInvert
Name Ethernet module
Mag-Audio
Additional options
Turning the device on wheel and button №1 or №2 will enter the HARDWARE
update mode. If update process will not be activated in 15 seconds, device will
reboot normally. In HARDWARE update mode yellow LED №1 indicates active
HARDWARE update mode (always lit). Yellow LED №2 indicates update
process (flashing when data stream is active). No messages on display.
Speaker preset base
Select Speaker preset
quantity - 50 pieces
Select Speaker preset
DSP menu for channel №2
The second DSP menu is
completely identical to
the first
The second DSP menu is
completely identical to
the first
Input selector
Analog_1
Analog_2
AES/EBU_1_1
AES/EBU_1_2
AES/EBU_2_1
AES/EBU_2_2
AES/EBU_3_1
AES/EBU_3_2
AES/EBU_4_1
Pair number 1
Pair number 2
Pair number 3
first press to call the DSP less than channel number 2
first press to call the DSP less than channel number 1
1513erD1518
three-level password protection
first level functions are available
all functions are available
there is a connection to the cinema equipment
there is a connection to the PC
ordinary message
alarm message
sleep message
standby mode message
mute sound mode message
event message
Copy menu for both channels
Both channels are identical
Both channels are not identical
Copy channel 1 to channel 2
Copy channel 2 to channel 1
Exit
Copy all six EQ bands from channel 1 to channel 2
Copy all six EQ bands from channel 2 to channel 1
Press key 1+ key2 for DSP menu
DSP menu for channel №1
12Rotate or press
Wheel
MENU STRUCTURE

TDC series user manual rev 1.0
10
MAG THEATRON