Ashly PE Series User manual

All Rights Reserved
PE-Series Amplifier
Operating Manual
Ashly Audio Inc.
847 Holt Road, Webster, NY 14580-9103
Toll Free [phone], Telephone [phone], FAX [phone]
www.ashly.com
All Trademarks referred to herein, are the property of their respective owners.

Page - 2 Operator Manual – PE Series Amplifiers
Copyright© 2005 – Ashly Audio Inc.
Introduction
Congratulations on your purchase of an Ashly PE-Series (Protea Enabled) amplifier. The PE-
Series is made up of high-power, high-efficiency, lightweight amplifiers incorporating the latest
in power and control technologies. We are confident that you will be pleased with the high
performance, superb sound quality, reliability, remote control and more.
About Ashly
Ashly Audio was founded in 1974 by a group of recording engineers, concert sound
professionals, and electronics designers. The first products were elaborate custom consoles for
friends and associates, but business quickly spread to new clients and the business grew. The
philosophy we established from the very beginning holds true today: to offer only the highest
quality audio tools at an affordable cost to the professional user – ensuring reliability and long
life. More than thirty years later, Ashly remains committed to these principles.
Ashly’s exclusive Five Year, Worry- Free Warranty remains one of the most liberal policies
available on any commercial- grade product. The warranty covers every product with the Ashly
brand name, and is offered at no extra cost to you, our customer.
Safety
This power amplifier can produce dangerous output voltage levels, high power
levels, and high sound pressure levels in connected loudspeakers. In order to
minimize the risk of injury, damage, or hearing loss, please read the entire
owner’s manual before connecting to a sound system.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation
point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance instructions in the literature accompanying the device.
aTO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO
USER SERVICEABLE PARTS INSIDE.
aREFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
aTO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
aTO REDUCE THE RISK OF FIRE, REPLACE ONLY WITH SAME TYPE FUSE.
REFER REPLACEMENT TO QUALIFIED SERVICE PERSONNEL.
aWARNING: THIS APPARATUS MUST BE GROUNDED THROUGH THE
SUPPLIED POWER LINE CORD
Introduction - 2
About Ashly
Safety
The PE Series - 3
Physical Description - 4
Installation - 5
Operation - 7
Troubleshooting - 8
Spec Table - 9
Measurements - 10
Dimensions - 11
Warranty - 12
This manual uses a
Perpetual Table Of
Contents. Each page has
a copy of the manual’s
contents in a gray box just
like this one. The section
you are in will always be
bold with the other
sections “grayed out.” The
feature allows you to jump
directly to another section
without having to return to
a Table Of Contents page.

Operator Manual – PE Series Amplifiers Page - 3
All Rights Reserved
The PE Series
PE-Series (Protea Enabled) amplifiers are high-power, high-efficiency, lightweight amplifiers
incorporating the latest amplifier technologies. Each amplifier can be controlled and monitored
through the Ethernet port using ProteaNE Software™ included on the CD that came with the
amplifier (visit Ashly.com to check for software updates). ProteaNE gives users access to many
features, including: input attenuation, channel mute, channel polarity, input level, output voltage,
output current, clipping, temperature and remote standby.
The series provides a wide power range of 400 to 1900 watts per channel at 4 ohms (20Hz-
20kHz, 0.05% THD). All models will drive 2, 4 or 8 ohm loads. Each models is 2RU, weighs
under 24 pounds and utilizes a state-of-the-art, efficient, high speed switched mode power
supply. DC voltage control of the input level and remote standby are among the many standard
features.
PE-Series Power Ratings
Stereo Mono Bridged Parallel-
Mono
Model 8Ω4Ω2Ω8Ω4Ω2Ω
3800 1,100W 1,900W 1,500W 3,800W 3,000W 3,800W
3000 9,00W 1,500W 1,500W 3,000W 3,000W 3,000W
2400 7,00W 1,200W 1,500W 2,400W 3,000W 2,400W
1800 500W 900W 1,400W 1,800W 2,800W 1,800W
1200 300W 600W 1,100W 1,200W 2,200W 1,200W
800 200W 400W 700W 800W 1,400W 800W
Input connections are via XLR/TRS Neutrik Combo, and 6-pin Euroblock connectors. XLR male
connectors are also provided for looping to additional amplifiers.
Output connectors are locking Neutrik Speakon, and screw terminal strip with safety cover.
Switches on the rear panel include: selectable High Pass Filters, Clip Limiter, Ground Lift, Gain
and Operation Mode.
Protection
PE-Series Amplifiers come standard with several protection circuits:
aClip Limiter – On overdrive the clip detection triggers the Attack-Release Circuit
delivering control voltage for gain reduction.
aSOA Protection - If the power transistors leave their Safe Operation Area, the
SOA-protection switches back the current rail of the respective channel.
aDC Protection - Each output is monitored for DC voltage. If thresholds are
exceeded, the corresponding channel will be muted. Minor DC occurrences (once
resolved) will return the amplifier to normal. If the DC condition is severe the
amplifier will enter standby.
aDC Servo - PE-Series has a DC Servo to prevent DC Offset at the output.
aOver Current Protection - Is controlled in the output stage.
aThermal Protection - When the internal temperature is below 40°C the fan runs
at its slowest speed. Above 40°C the speed is increased until it reaches its
maximum value. If the temperature exceeds 100°C, both channels are muted.
aMains Protections – protection within the power supply includes: Inrush Current
Limitation, Mains Over Voltage Detection, Mains Failure Detection, and Fuse
Protection.
Introduction - 2
The PE Series - 3
Protection
Physical Description - 4
Installation - 5
Operation - 7
Troubleshooting - 8
Spec Table - 9
Measurements - 10
Dimensions - 11
Warranty - 12

Page - 4 Operator Manual – PE Series Amplifiers
Copyright© 2005 – Ashly Audio Inc.
Physical Description
Each model in the PE-Series is 2RU, and weighs under 24 pounds. They all share the same
physical design. The model number is indicated in the lower left corner of the front panel
Amplifier Front Panel
1. Mounting Holes – For rack mounting.
2. Power Switch – Switches the unit on or off
3. Status LEDs – Indicate status of: Power,
Standby, Protect, Operating Mode and Comm
data
4. Air Inflow Vents – Cool air enters here
5. Channel Controls – Channel control area
6. Signal LEDs – The lowest LED will begin to light
when the output voltage reaches approximately 4
volts. When clipping occurs the Clip/Mute LEDs
will begin to flash. If clipping
becomes severe the LEDs will remain on. This
LED will also illuminate if the cahnnel is muted.
7. Temperature & Current Indicators – These
LEDs illuminate proportionally to the heat-sink
temperature and output current, respectively.
8. Channel Attenuators – For adjustment of the
input signal.
Amplifier Rear Panel
1. Input Ground Lift – This switch isolates or
connects the signal ground to the power ground
2. High Pass Filter (both channels) – This switch
sets the High Pass Filter for each channel to
30Hz, 50Hz or Off. Depending on your system
set-up, there may be an audible "pop" when
engaging the HPF. It is recommended that you
operate these switches with the amplifier off.
3. Operating Mode – This switch selects the
amplifier’s operating mode (Bridge, Stereo, or
Parallel). NEVER OPERATE THIS SWITCH WITH
THE AMPLIFIER ON.
4. Input Gain – This switch sets the amplifier gain to
26dB, 32dB, or 1.4V sensitivity.
5. Clip Limiter – This switch sets the clip limiting
circuitry to Off, Slow or Fast.
6. Input Module – Details on the next page
7. Cooling Air Outflow Vents – These vents must
remain open and unobstructed at all times
8. Speakon™ Output Connectors – These
connectors provide a convenient and fast
connection to your speakers.
9. Screw Terminal Output Connectors – These
traditional connectors can be used in tandem with
(impedance dependent) or in lieu of the Speakon
output connectors
Introduction - 2
The PE Series - 3
Physical Description - 4
Front Panel
Rear Panel
Input Module
Installation - 5
Operation - 7
Troubleshooting - 8
Spec Table - 9
Measurements - 10
Dimensions - 11
Warranty - 12

Operator Manual – PE Series Amplifiers Page - 5
All Rights Reserved
Input Module
The PE-Series has been designed
with flexibility in mind. The input
section illustrated at right has been
engineered in modular form. All
amplifiers ship with the standard
input (shown) unless the Optional 32
bit/96kHz ProteaNE DSP card is
specified. This optional module
features both analog and digital
(AES/EBU) inputs, and two
additional processed output channels
to drive additional amplifier channels. Documentation for this module is provided in a separate
document. If there is an input feature or function you’d like to see developed for the PE-Series,
please contact Ashly.
1. XLR/TRS Combo Balanced Inputs – These
connectors accept either a Male XLR or 1/4” TRS
plug.
2. Channel Input Turnarounds – These connectors
provide signal to additional amplifiers via male XLR
jacks.
3. Euroblock Connector Channel Inputs – These
connectors are in parallel with the Combo Inputs and
allow for signal connection using Euroblocks.
4. Remote Level Control Connector – This connector
facilitates hard-wired remote attenuation control.*
5. Remote Standby Connector – This connector
facilitates hard-wired remote on/off functionality.*
6. Ethernet Connector & Indicators – This RJ45
Ethernet connector interfaces with a Protea NE
network, or computer if available. The indicators
show network link and data activity.
7. Reset – This allows you to perform a factory reset to
return all parameters back to the factory defaults.
With the power off, insert a long thin lead (like a
paper clip) into the hole. Turn on the power and hold
in the switch. The signal LEDs on the front panel will
light in sequence (-15 to clip). When the sequence is
complete (about five seconds) and all signal LED’s
illuminate simultaneously, the factory settings have
been restored.
*See the wiring diagram on page 11 for more
information.
Installation
PE-Series amplifiers are designed for use in both fixed and mobile sound systems. Each
amplifier is shipped (unless otherwise specified) with the following factory settings:
Front panel: Rear panel:
On/Off Switch = Off
Attenuators = ∞
Input Ground Lift = Grounded
High Pass Filters (both Ch.) = Off
Mode Selector = Stereo
Clip Limiter = Off
Gain Selector = 32 dB
Before connecting to mains power, make sure that the switches are set to the configuration
needed for your particular application. Always switch the amplifier off before making any
changes to the settings. Failure to do so could result in damage to the unit or other components
in your system. Use four screws and washers when rack mounting the amplifier. For mobile use,
the unit should be secured using the rear rack mounting ears.
Requirements
PE-series amplifiers have specific physical, electrical and signal requirements for proper
operation. These requirements will vary depending on your specific application, setup, and the
settings on the amplifier. When setting up and testing your system, please take special care to
double check all connections and settings. Please refer to the specifications section of this
manual for specific input, output and other figures.
Introduction - 2
The PE Series - 3
Physical Description - 4
Front Panel
Rear Panel
Input Module
Installation – 5
Requirements
Typical Applications
Connectors&Polarity
Operation - 7
Troubleshooting - 8
Spec Table - 9
Measurements - 10
Dimensions - 11
Warranty - 12

Page - 6 Operator Manual – PE Series Amplifiers
Copyright© 2005 – Ashly Audio Inc.
Typical Applications
The most common use
of a PE-Series amplifier
is a 2-channel source
driving 2 speaker
channels. In this
illustration, the PE-
Series amplifier is
receiving a signal and
then ‘returns’ it to a
second amplifier using
the provided
connectors. The
amplifier is in STEREO
mode.
Because of their efficient
and high-power design,
PE-Series amplifiers are
well suited to single
channel output to mono
speaker load such as a
subwoofer. This
illustration shows both
PARALLEL and
BRIDGED output
connections using a single
input signal.
Connectors & Polarity
PE-Series amplifiers utilize several different professional audio connectors. The Euroblock
and Screw-Terminal connectors are clearly marked on the amplifier’s rear panel and are
straightforward. The connection polarity for the other three types of connectors (XLR, TRS,
and Speakon) are less obvious. The diagrams below show how each connector should be wired
for proper operation. Be sure to read the Operation section of this manual for important
information on the three operating modes.
Introduction - 2
The PE Series - 3
Physical Description - 4
Installation – 5
Requirements
Typical Applications
Connectors&Polarity
Operation - 7
Troubleshooting - 8
Spec Table - 9
Measurements - 10
Dimensions - 11
Warranty - 12

Operator Manual – PE Series Amplifiers Page - 7
All Rights Reserved
Operation
The amplifier’s On/Off Switch is a rocker-type switch located on the left side of the front panel.
Turning on the amplifier initiates start-up by activating the inrush current limiter. During power
up, the Clip/Mute, Standby and Protect LEDs from both channels will light up for a few seconds.
When using the remote On/Off function, the main On/Off switch must remain in the On position.
See page 11 for more information on remote On/Off connections.
NOTE: The power switch does NOT isolate the appliance from mains. As soon as the unit is
connected to the mains power supply, a voltage is supplied to both the line-filter and the fused
input of the controllable rectifier. If a power interruption occurs while the unit is switched on, it
will restart automatically when power is restored and all settings will be maintained.
2 Channel (Stereo) Mode
In this mode, the amplifier’s two channels operate fully independent of each other. Each signal
enters the unit and is amplified separately.
Parallel-Mono Mode
In this mode, a single input signal (connected to channel 1) is connected to the two output
channels. The output terminals of the two channels are configured in parallel using an internal
relay. The (single) load is connected either to the output of channel 1 or to that of channel 2 (as
if in stereo). While the total output of the amplifier remains the same and the output voltage
level is also the same as in stereo operation, the minimum impedance that can be connected is
reduced by half because the current capability is doubled. Only the Channel 1 attenuator is
active. The Channel 2 attenuator should be turned down to zero. This mode is useful when
identical loudspeakers are to be operated with the same power.
IMPORTANT: When connecting speaker cabinets in parallel, always use all the contacts in
both SPEAKON connectors. If not, this can cause permanent damage to the connectors and
considerably reduce performance.
Bridged Mono Mode
In this mode, a single input (connected to channel 1) is connected to the two output channels
that have been ‘Bridged” together. Each output channel processes the signal, but the polarity of
channel 2 is reversed. The (single) load is connected between the two positive channel outputs
using a suitably connected SPEAKON connector. While the total output of the amplifier
remains the same, both the available output voltage and the minimum impedance that can be
connected are doubled, as compared with stereo operation. Only Channel 1 is active. A signal
feeding Channel 2 will have no effect on the output. Turn the attenuator of Channel 2 down to
zero.
WARNING! In Mono-Bridge mode RMS output voltages as high as 230 V. Wiring to the
speaker loads must conform to NEC Class 3 safety standards or its equivalent. All customer
specific cables should only be manufactured by qualified personnel.
Introduction - 2
The PE Series - 3
Physical Description - 4
Installation – 5
Operation – 7
2 Channel Mode
Parallel Mode
Bridged Mode
Troubleshooting - 8
Spec Table - 9
Measurements - 10
Dimensions - 11
Warranty - 12

Page - 8 Operator Manual – PE Series Amplifiers
Copyright© 2005 – Ashly Audio Inc.
Troubleshooting
Situation Indication Action
Signal LED not lit
Clip LEDs not lit Check AC plug. Confirm that AC outlet works by plugging in another device.
Output Current LEDs are lit
Signal LED not lit (or low) Check for a shorted speaker cable or speaker/driver.
Output Current LEDs not lit
Signal LEDs responding to signal level Check the speaker wiring for breaks. Try another speaker and cable.
No Sound
Clip/Mute LEDs show red, and Protect
status indicator is illuminated (Protect
Mode)
Overheating will cause protective muting. Check for proper
ventilation. If the fan isn’t running the amplifier requires
servicing.
No Channel
Separation No Channel Separation Check the mode indicators on the front panel and make sure the mode selector on the rear panel is in the stereo-position.
Make sure other equipment in the signal path such as mixers
and preamps are set for stereo, not mono
Power LED is lit A faulty speaker or a loose connection could cause this.
Check the wiring and try another speaker.
Signal LEDs responding to signal level The signal source might be clipping. Keep the volume pots at
least halfway up so that the source does not have to be
overdriven.
Distorted Sound
Clip LEDs not lit Keep the volume pots at least halfway up and try changing
input sensitivity from 1,4 V to 32 dB or 26 dB with the gain
selector on the rear.
Hiss Hiss Unplug the amplifier input to confirm that the hiss is coming
from the source or from a device upstream. Erratic or popping
noises indicate an electronic fault in the offending unit. To
keep the noise floor low, operate the primary signal source at
full level, without clipping. Avoid boosting the signal further
between the source and the amplifier.
Squeals and
Feedback Squeals and Feedback Microphone feedback should be eliminated with mixer controls. If noise continues to build up with no microphone
gain, there is a serious fault in the signal processors or
cables. Working in succession from the signal source towards
the amplifier and check each device in the signal path by
reducing its gain or by unplugging it.
Comm LED lit Check connection between computerand any routers or
switched in the network. Reboot computer. If issue is not
resolved, consider replacing CAT-5 Cables
Protea
Communications
Failure Comm LED not lit Check connection between amplifier andnetwork. Reboot
computer. If issue is not resolved, consider replacing CAT-5
Cables
Introduction - 2
The PE Series - 3
Physical Description - 4
Installation – 5
Operation – 7
Troubleshooting - 8
Spec Table - 9
Measurements - 10
Dimensions - 11
Warranty - 12

Operator Manual – PE Series Amplifiers Page - 9
All Rights Reserved
Spec Table (All Specifications Subject to Change or Improvement Without Notice.)
Optional ProteaNE/DSP Input Card
Latency (48 kHz/96/kHz) Analog Inputs: 1.42ms/.71ms Digital Inputs: .65ms/.32ms
A/D, D/A Converters: 24-bit, 96-kHz
DSP 24-bit conversion with 32-bit, floating-point DSP processing
Digital Input AES/EBU, 16-24 bit, 48 or kHz.
DSP Modules Signal Processing
Delay, Compressor/Limiter
EQ: Graphic and Parametric
HPF/LPF: Up to 48 dB/octave
Signal Generator: Sine Wave, White Noise and Pink Noise
PE-800 PE-1200 PE-1800 PE-2400 PE-3000 PE-3800
Power Output
Stereo Mode, both channels driven
8 ohms, 20 Hz - 20 kHz, 1% THD 200 W 300 W 500 W 700 W 900 W 1,100 W
4 ohms, 20 Hz - 20 kHz, 1% THD 400 W 600 W 900 W 1,200 W 1,500 W 1,900 W
2 ohms, 20 Hz - 20 kHz, 1% THD 700 W 1,100 W 1,400 W 1,500 W 1,500 W 1,500 W
Bridged Mono Mode
8 ohms, 20 Hz - 20 kHz, 1% THD 800 W 1,200 W 1,800 W 2,400 W 3,000 W 3,800 W
4 ohms, 20 Hz - 20 kHz, 1% THD 1,400 W 2,200 W 2,800 W 3,000 W 3,000 W 3,000 W
Parallel Mono Mode
2 ohms, 20 Hz - 20 kHz, 1% THD 800 W 1,200 W 1,800 W 2,400 W 3,000 W 3,800 W
Signal to Noise (20 Hz-20 kHz,
unweighted, 26 dB amplifier gain): >98 dB >105 dB >108 dB >110 dB >111 dB >112 dB
Voltage Gain: 26 dB, 32 dB or 1.5 V sensitivity (selectable)
Output Circuitry: Bipolar, Class AB Bipolar, Class AB Bipolar, Class H Bipolar, Class H Bipolar, Class H Bipolar, Class H
Current Draw (both channels driven ) Typ Max Typ Max Typ Max Typ Max Typ Max Typ Max
Idle 2.4A 2.8A 2.4A 2.4A 2.6A 2.8A
8 ohms 6.6A 13.6A 8.6A 20.2A 8.4A 26.2A 10.4A 33A 12.4A 42A 14.6A 50A
4 ohms 9.4A 21.8A 13.6A 33.8A 13A 42A 15.8A 54A 19.6A 68A 22.6A 80A
Power Requirements
*(1/8 Power Pink Noise @ 4 Ohm): 420W 640W 611W 790W 1010W 1220W
Power Cable Connector 15A Edison 30A Twistlock 30A Twistlock 30A Twistlock 30A Twistlock 30A Twistlock
All Models
Distortion (SMPTE, typical) - 8 ohm load,
10 dB below rated power <.01%
Distortion (THD+N, typical) - 8 ohm load,
10 dB below rated power, 20 Hz - 10 kHz <.01%
Frequency Response 20 Hz - 20 kHz, +/- 0.15 dB
Damping Factor -8ohmload,<1kHz > 400
Input Impedance 20 kOhm, balanced
Maximum Input Level: +21 dBu
Cooling temperature dependent speed-controlled axial fan
Control Network: onboard, compatible with standard 10 Base-T/100 Base-TX Ethernet hardware
Front Panel Indicators Per channel: Clip, -6 dB, -12 dB, -18 dB, Temp, Output current.
Overall: power, standby, protect, bridged mono, parallel mono, communications
Attenuators: Per channel: front panel, software, offset and remote
Input Connectors, each channel XLR female/TRS, Euroblock, XLR male (looping)
Output connectors, each channel Speakon, screw terminals
Amplifier Protection inrush current limitation, temperature monitoring heat-sinks, output DC protection, power transistor SOA protection, output
over-current protection, mains fuses protection
Load Protection
A
djustable clip limite
r
Dimensions 19"W x 3.0"H x 13.5"D / 483mmW x 88.9mmH x 340mmD
Weight (lbs./kg) 22 to 24 lbs / 10 to 10.9 kg Net, 27 to 29 lbs / 12.3 to 13.2 kg Shipping
Introduction - 2
The PE Series - 3
Physical Description - 4
Installation – 5
Operation – 7
Troubleshooting - 8
Spec Table - 9
Measurements - 10
Dimensions - 11
Warranty - 12

Page - 10 Operator Manual – PE Series Amplifiers
Copyright© 2005 – Ashly Audio Inc.
Measurements
The following graphs are actual measurements from PE-Series amplifiers during typical use.
Gain vs. frequency, Ch1, Ch2 - (typical performance) Gain vs. frequency / positions of HPF, Ch1, Ch2
Phase vs. frequency, Ch1, Ch2 Phase vs. frequency / positions of HPF-Switch, Ch1, Ch2
Output impedance vs. frequency @ 1 Amp RMS injected current
(Ch1, Ch2) equivalent 11 mΩ+ 2,1 µH THD+N @ 1 kHz, 8 Ωload vs. input voltage, Ch1, Ch2
Damping factor into 8 Ω, Ch1, Ch2 equation: damping factor = loaded
impedance / amplifier output impedance THD+N vs. frequency (BW 22 kHz), 10 dB below clip, 8Ω, Ch1, Ch2
CCIF difference frequency method (10,5 kHz and 11,5 kHz) vs. input
level @ 8 Ω, Ch1, Ch2 SMPTE intermodulation distortion (60 Hz and 7 kHz) @ 8 Ωvs. input level, Ch1, Ch2
Common mode rejection ratio (Ch1, Ch2) Channel separation vs. frequency
@ 10 W / 8 Ω(Ch1 => Ch2, Ch2 => Ch1)
Introduction - 2
The PE Series - 3
Physical Description - 4
Installation – 5
Operation – 7
Troubleshooting - 8
Spec Table - 9
Measurements - 10
Dimensions - 11
Warranty - 12

Operator Manual – PE Series Amplifiers Page - 11
All Rights Reserved
Amplifier Dimensions
All PE Series amplifiers share the same dimensional measurements:
Remote Level & Power Connections
Introduction - 2
The PE Series - 3
Physical Description - 4
Installation – 5
Operation – 7
Troubleshooting - 8
Spec Table - 9
Measurements - 10
Dimensions - 11
Warranty - 12

Page - 12 Operator Manual – PE Series Amplifiers
Copyright© 2005 – Ashly Audio Inc.
Limited Warranty
Warranty service for this unit will be provided by ASHLY AUDIO, INC. in accordance with the
following warranty statement.
ASHLY AUDIO, INC. warrants to the owner of this product that this product and the
components thereof, will be free from defects in workmanship and materials for a period of FIVE
years from the date of purchase. ASHLY AUDIO INC. (ASHLY AUDIO) will, without charge,
repair or replace, at its option, defective product or component parts upon prepaid delivery to the
factory service department or authorized service center, accompanied by proof of purchase date
in the form of a valid sales receipt. This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
EXCLUSIONS: This warranty does not apply in the event of misuse, neglect or as a result of
unauthorized alterations or repairs. This warranty is void if the serial number is altered, defaced,
or removed. ASHLY AUDIO reserves the right to make changes in design or make additions to
or improvements upon this product without any obligation to install the same on products
previously manufactured.
Any implied warranties which may arise under the operation of State law shall be effective only
for FIVE years from the date of purchase of the product. Ashly Audio shall be liable only to
correct defects in the product itself, and not for any damage or injury which may result from or
be incidental to or a consequence of such defect. Some states do not allow either limitations on
how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you.
OBTAINING WARRANTY SERVICE:
For warranty service in the United States, please follow this procedure:
1.) Return the product to Ashly, freight prepaid, with a written statement describing the defect
and application the product is used in. Ashly Audio will examine the product and perform
any necessary service, including replacement of defective parts, at no further cost to you.
2.) Ship your product to:
Ashly Audio Inc.
Attn: Service Department
847 Holt Road
Webster, NY 14580-9103
For units purchased outside The United States of America, service will be provided by an
authorized distributor of ASHLY AUDIO, INC.
Introduction - 2
The PE Series - 3
Physical Description - 4
Installation – 5
Operation – 7
Troubleshooting - 8
Spec Table - 9
Measurements - 10
Dimensions - 11
Warranty - 12