Magellan FSMGMC7003 Owner's manual

Three Tier Kayak Rack
FSMGMC7003
Customer Service: [phone]
7:00 am to 12:00 am CST (daily)
Live Chat at: www.academy.com
Email: [e-mail]
Please keep this instruction manual for future reference
Assembly Instructions
& User Manual

Table of Contents
Page 1 of 15
Note: Before beginning assembly of product, make sure
all parts are present. Compare parts with package content
list and hardware contents. If any part is missing or
damaged, do not attempt to assemble the unit. Contact
customer service for replacement parts.
Warnings…………………………………………………………………..2
Tools and Parts…………………………………………………………3-5
Assembly Instructions………………………………………………...6-12
User Instruction ………………………………………………………....13
Care and Maintenance………………………………………………….14
Warranty Information………………………………………..................15

Warnings
Page 2 of 15
Read carefully and understand all INSTRUCTIONS before operating. Failure to
follow the safety rules and other basic safety precautions may result in serious
personal injury. It is the user’s responsibility to read and follow all instructions.
The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions or situations that could occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
- Recommended for two capable adults for assembly.
- Keep these instructions with the product at all times and review before each
use.
- Keep work area clean, free of clutter, and well lit. Cluttered and dark work
areas can cause accidents.
- Keep children and bystanders away while assembling the Kayak Rack.
Distractions can cause you to lose control, so visitors should remain at a safe
distance from the work area.
- Use safety apparel and equipment when assembling the Kayak Rack.
- Inspect the product before each use to ensure it is assembled properly and all
parts are in safe working order and free of defects.
- Never modify this product in any way.
-DO NOT exceed the 100 lb weight capacity on each holder set.

Parts List
A Left Leg Frame 1pcs
B Right Leg Frame 1pcs
C Cross Support for Leg Frame 2pcs
D Bottom Upright 2pcs
E Cross Support for Bottom Upright 1pc
F Top Upright 2pcs
G Cross Support for Top Upright 1pc
H Bottom Upright Support 2pcs
I J-Holder 4pcs
J L-Holder 2pcs
K U-Clip 6pcs
L Safety Strap with Buckle 6pcs
M Leg Extension 2pcs
Page 3 of 15

Hardware
1 Leveling Foot 6pcs
2 M8X60 Hex Screw 8pcs
3 Ø8mm Washer 52pcs
4 M8 Nylon Lock Nut 28pcs
5 M8X16 Hex Screw 14pcs
6 M8X75 Round Phillips Screw 12pcs
7 M5X60 Round Phillips Screw 6pcs
8 Ø5mm Washer 6pcs
9 M5 Nylon Lock Nut 6pcs
10 J-Hook 8pcs
11 M8 Hex Nut 8pcs
12 M8X90 S/S Lag Screw 2pcs
13 Plastic Bushing 2pcs
Page 4 of 15
1 Wrenches (Included)
8mm, 12mm & 13mm
2 #2 Philips screwdriver
(Not Included)
Tools Required

Marking
M1 Indicates where to install screw, washer &
nut set.
M2 Indicate where to install part to.
M3 Indicates the direction of looping the safety
strap.
Page 5 of 15

Assembly Instructions
Step 1:
Step 2:
Page 6 of 15
FIG.1
FIG.3
FIG.4
FIG.2
Install and fully insert Leveling Foot (1) to Left Leg
Frame (A) and Right Leg Frame (B). FIG.1
Align and assemble the Left Leg Frame, Right Leg
Frame, and Cross Support for Leg Frame (C).
FIG.2
Align and assemble the Bottom Upright (D) and
Cross Support for Bottom Upright (E). Carefully
put it on the Leg Frame Assembly. FIG.3
Align and assemble the Top Upright (F) and Cross
Support for Top Upright (G). Carefully put it on the
Bottom Upright Assembly. FIG.4

Assembly Instructions
Align Leg Frame, Bottom Upright, and Bottom
Upright Support (H) mounting holes.Align the
mounting holes of Bottom Upright(D) and Top
Upright (F) . Install and tighten (do not firmly
tighten yet) M8X60 Hex Screw (2), Ø8mm
Washer (3) and M8 Nylon Lock Nut (4). FIG.5
Repeat this step to assemble the other side.
To complete the assembly, you will need M8X60
Hex Screw x 8pcs, Ø8mm Washer x 8pcs and
M8 Nylon Lock Nut x8pcs. Hardware for this
assembly is packed together.
* Remove the Hex Screws, Washers, and Nylon
Lock Nuts where are pointed first, when J-
Holders are mounted here.
FIG.5
FIG.6
Install and tighten (do not firmly tighten yet)
M8X16 Hex Screw (5), Ø8 mm Washer (3), to the
Leg Frame, Cross Supports ,Top Upright, and
Bottom Upright assembly. FIG.6
* To complete the assembly, you will need M8X16
Hex Screw x 12pcs, Ø8mm Washer x 12pcs,
Hardware for this assembly is packed together.
Step 3:
Step 4:
Page 7 of 15

Assembly Instructions
Step 5: FIG.7
Align the J-Holder (I), Top Upright, and Bottom
Upright mounting holes. Install and tighten (do not
firmly tighten yet) M8X75 Round Phillips Screw (6),
Ø8mm Washer (3), and M8 Nylon Lock Nut (4).
FIG.7
There are several mounting holes on Top & Bottom
Uprights. Options for assembling the J-Holders to
different positions to suit your best need.
•There are two J-Holders with logo, and two without.
Mount two J-Holder with logo to the middle of
Bottom Upright; the two without logo to the top
Upright.
Align the L-Holder (J) and Leg Frame mounting holes.
Install and tighten (do not firmly tighten yet)
M8X75 Round Phillips Screw (6), Ø8mm Washer (3),
and M8 Nylon Lock Nut (4).
•There are several mounting holes on Leg Frames,
options for assembling the L-Holder to different
positions to fit different sizes of kayak or canoe here.
FIG.8
* To complete the J-Holder & L-Holder assembly,
you will need M8X75 Round Phillips Screw x
12pcs, Ø8mm Washer x 12pcs and M8 Nylon
Lock Nut x 12pcs. Hardware for this assembly is
packed together.
FIG.8
Page 8 of 15

Assembly Instructions
Step 6:
a
b
c
Un-tie the Safety Strap(L). FIG.9
(a. Male Buckle ; b. Female Buckle ; c. Loop.)
Find the loop sew on the strap,and slip it
through U-Clip (K).
Align the U-Clip and J-Holder mounting holes.
Install and firmly tighten M5X60 Round Phillips
Screw (7), Ø5mm Washer (8), and M5 Nylon
Lock Nut (9). FIG.10
Repeat above to assemble the U-Clip to the
rest of the J-Holders.
*To complete the U-Clip assembly, you will need
M5X60 Round Phillips Screw x 6pcs, Ø5mm
Washer x 6pcs, and M5 Nylon Lock Nut x
6pcs.
4 sets for U-Clip / J-Holder assembly; 2 sets for
U-Clip / Bottom Upright assembly (Step 7).
Hardware for Step 6 & 7 are packed together.
FIG.9 FIG.10
Step 7:
Slip the loop on the safety strap through U-Clip.
Align the U-Clip and Bottom Upright mounting
holes. Install and firmly tighten M5X60 Round
Phillips Screw (7), Ø5mm Washer (8), and M5
Nylon Lock Nut (9). FIG.11
Repeat above to assemble U-Clip to the other
Bottom Upright.
Before installing safety straps to the J-Holders
and L-Holders ( Step 8 ), check the complete
Kayak Rack Assembly, firmly tighten all
screws attached.
FIG.11
Page 9 of 15