Magnadyne M9900CD User manual

Installation
and Operations
Manual
R
M9900CD
AM / FM / WB and CD Stereo Receiver
9900CD Manual 1/20/03 12:19 PM Page 1

Your new in-dash entertainment system has been designed for many years of listening pleasure. Take a
moment to read through this manual and become familiar with the operations and features of this out-
standing product.
It is advisable to keep this manual in your vehicle ready for reference. We hope the experience with your new
mobile entertainment system is a pleasurable one. Be sure to fill out and send in your warranty card. In the
unlikely event that your system will need service during the warranty period, you will need to be registered
to receive the full benefits of warranty repair.
Introduction
Location and Function of Controls at a Glance
2
1. Power On/Off: Press this button to turn the unit on.
2. Volume/Sound Controls: Rotate the button to increase or decrease the volume level. Press to scan
between the different sound controls (Volume, Bass, Treble, Balance and Fader).
3. Multi-Function Knob: Rotate to change radio stations. Press to scan radio stations. Rotate to adjust hours
and minutes for clock setting. Rotate to change tracks when a CD is playing.
4. Multi-Function Button #1: Press when programming a radio station into memory #1 (CH1). Press when
recalling memorized radio station #1. Press to play or pause when a CD is inserted.
5. Multi-Function Button #2: Press when programming a radio station into memory #2 (CH2). Press when
recalling memorized radio station #2. Press to repeat a single track from the CD.
6. Multi-Function Button #3: Press when programming a radio station into memory #3 (CH3). Press when
recalling memorized radio station #3. Press to preview each song on the CD for 10 seconds.
7. Multi-Function Button #4: Press when programming a radio station into memory #4 (CH4). Press when
recalling memorized radio station #4. Press to play the CD that precedes the one that is currently playing
in the optional CD changer.
9900CD Manual 1/20/03 12:19 PM Page 2

3
Location and Function of Controls at a Glance (Continued)
8. Recall Button #5: Press when programming a radio station into memory #5 (CH5). Press when recall-
ing memorized radio station #5. Press to play the CD that follows the one that is currently playing in the
optional CD changer.
9. Weather Band Radio Button: At any time when the unit is on, press this button to access the weather
band radio.
10. Logic Reset Button: If the display or front panel functions become locked and inoperative, press this
button to return all logic back to “Default Mode”. Note: All clock and station recall memory will be lost.
11. Display Button:
Press this button at any time, when the unit is on, to display the clock indefinitely.
If you tune to another radio station the radio frequency will be displayed for 5 seconds then will
switch back to the clock. Pressing the "Display" button a second time will display the radio fre-
quency indefinitely. This procedure operates the same for CD mode.
12. Radio Band Select Button: Press this button to select FM1, FM2, FM3, AM1 or AM2 radio bands.
13. Source Mode Button: Press this button to change the play source. If a CD is loaded, and the radio is
playing, you can press the “MODE” button to switch between each source.
14. CD Eject Button: Press this button to eject a CD.
15. CD Slot: To play a CD, insert CD into slot with label facing up.
16. Radio Station/ Clock Display Area: This area displays the radio station, last pushed station recall but-
ton and the clock.
17. CD Function Display Area: This area of the display shows all CD and function indicators.
9900CD Manual 1/20/03 12:19 PM Page 3

4
Listening to the Radio
1. Pushthe“POWER”button(1)oncetoturntheuniton.
2. Press the “BAND” button (12) to select a radio
band: FM1, FM2, FM3, AM1 or AM2.
3. To manually tune in a radio station, rotate the
“Tuning” knob (3) right or left until the desired
station is located.
4.To “Automatic Scan” to the next strong station.
Press and release the “Tuning” knob (3). The
tuner will scan up and wait for 5 seconds then
scan up again. Once the desired station is found,
press the knob again to stop the scan function.
5. To “Seek” up or down to the next station, momen-
tarily rotate the “Tuning” knob (3) right or left
and hold it for more than one second then
release it.
Programming the Unit
You can program up to 15 FM radio stations and 10 AM radio stations.
1. Select FM1, FM2, FM3, AM1 or AM2 by pressing the “BAND” button (12) repeatedly while watching the
indication on the display (16).
2. Use the “Tuning” or “Scan” (3) knob to select the desired station.
3. Press and hold one of the five station recall buttons (4-8). The button number and “CH” appears in the
display area (16). Release the button.
4. Repeat the procedure to memorize more stations as desired.
Sound Controls
Volume Button:
Press the “VOLUME” button (2) to select between
the sound controls Volume, Bass, Treble, Balance
and Fader (Figures A-E).
Bass Control:
The bass control adjusts the amount of low
frequency that you hear.
Treble Control:
The treble control adjusts the amount of high
frequency that you hear.
Balance Control:
The balance control adjusts the amount of sound
output to the left and right speakers.
Fader Control:
The fader control adjusts the amount of sound
output to the front and rear speakers.
☛
Figure A
Figure B
Figure C
Figure D
Figure E
9900CD Manual 1/20/03 12:19 PM Page 4

5
1. Press the “W.BAND” button (9) to activate the
weather band radio. (The weather band radio will
then take priority over the AM/FM Radio or CD).
The weather band radio will search for the
strongest radio signal in your area.
2. To scan all 7 weather band stations, press the
“Scan” button (3)
3. Press the “W.BAND” button once again to turn off
the weather band radio.
Weather Band Radio Operation
CD Operation
☛
☛
Figure A
Figure B
1. Insert a compact disc into the CD disc slot
(15). The disc will auto load and auto play (The
disc icon in the display will begin to rotate). If
the disc does not auto load, do not force it.
Press the “Eject” button (14) as you may
already have a disc inserted.
2. To change the music track, rotate the “Track”
knob (3) to the right or left (Figure A). Track
change indication will appear in the display
area (17).
3. To preview each song on the disc for 10 sec-
onds, press the “INTRO” button (6). “INT” will
appear in the display area. To turn off this fea-
ture, press the “INTRO” button again. The indi-
cator in the display will disappear (Figure B).
☛
9900CD Manual 1/20/03 12:19 PM Page 5