Magnadyne Keypad Keyless Entry System MKE-100 User manual

User's Manual
Keypad Keyless
Entry System
Models:
MKE-100 / MKE-300 / MKE-400
For Technical Assistance call [phone] or visit www.magnadyne.com
Programming
A. 3-Button Transmitter Programming
(Does not apply to MKE-100)
Note: This mode will only retain the last 4 remote
transmitters programmed. If the transmitter mem-
ory is exceeded, the security system will start
deleting transmitters from memory in chronologi-
cal order.
1. Turn the ignition switch to the "ON" position
within 15 seconds.
2. Push the Program switch 3 times, the
onboard LED will be flashing and the beeper will
emit a long chirp to indicate the system is in
Transmitter Programming mode.
3. Press and hold any button on the transmitter
until the onboard LED turns on for 2 seconds
and the beeper responds with a confirming
chirp, indicating the signal has been stored into
memory.
4. If you have additional transmitters (up to 4)
that need to be programmed, repeat step 3 for
each transmitter.
Exit: Turn the ignition switch to the "OFF" posi-
tion, or leave it for 15 seconds. The onboard
LED turns off and the beeper will emit 3 long
chirps to confirm exit.
B. 4-Button Transmitter Programming
(Does not apply to MKE-100)
Note: This mode will only retain the last 4 remote
transmitters programmed. If the transmitter mem-
ory is exceeded, the security system will start
deleting transmitters from memory in chronologi-
cal order.
1. Turn the ignition switch to the "ON" position
within 15 seconds.
2. Push the Program switch 5 times, the
onboard LED will be flashing and the beeper will
emit a long chirp to indicate the system is in
Transmitter Programming mode.
D. Programming the User Code
(The default user code is "54321" )
Note: This mode will only retain the last 4 "user
codes" programmed. If the user code memory is
exceeded, the security system will start deleting
user codes from memory in chronological order.
1. Enter the program code "12345" on the key-
pad. The beeper will emit a long chirp to confirm
the correct code was entered.
2. Enter a new 4 to 6 digit user code on the key-
pad. Do not use "1234".
3. Finish by pressing the "LOCK" key on the key-
pad. 1 long beep with 2 short beeps will confirm
the new user code has been stored into memory.
4. If you have additional user codes (up to 4)
that need to be programmed, repeat steps 2-3
for each new user code.
Exit: Press and hold the "LOCK" key for 1 sec-
ond or if 15 seconds of inactivity occurs during
the above steps, the unit will revert back to the
last successfully stored code. 3 longs beeps
confirm exit.
Locks All Doors
(Including Cargo)
Locks All Doors
(Including Cargo)
Press Simultaneously to
Turn On / Off Porch Light
Locks All
Cargo Doors
Unlocks All
Cargo Doors
Unlocks Entry
Doors
Unlocks Entry
Doors
Turns On / Off
Porch Light
Transmitters

Transmitter Button System Function
Locks the Vehicle's Doors and
Cargo Door
Unlocks the Vehicle's Doors
Locks the Cargo Door
Unlocks the Cargo Door
Turns On the Porch Light for
30 Seconds or Turns the Porch Light Off
Remark
Parking Lights Flash Once
1. Parking Lights Flash Twice
2. Dome Light Turns On for 30 Seconds
3. Porch Light Turns On for 30 Seconds
Note: If vehicle is operating from the RV
battery only, the parking lights will not flash.
Upon Vehicle's Door Unlock
Operation
A. 4-Button Transmitter Operation
+
Transmitter Button System Function
Locks the Vehicle's Doors and
Cargo Door
Unlocks the Vehicle's Doors
Turns On the Porch Light for
30 Seconds or Turns the Porch Light Off
Remark
Parking Lights Flash Once
1. Parking Lights Flash Twice
2. Dome Light Turns On for 30 Seconds
3. Porch Light Turns On for 30 Seconds
Note: If vehicle is operating from the RV
battery only, the parking lights will not flash.
Upon Vehicle's Door Unlock
B. 3-Button Transmitter Operation
System Function
Locks the Vehicle's Doors and
Cargo Door(s)
Unlocks the Vehicle's Doors
Locks or Unlocks the Cargo Door
(Operation is Sequential)
Turns On the Porch Light or Turns Off the
Porch Light (Operation is Sequential)
Activates the Channel 3 Output
Activates the Channel 4 Output
Activates the Channel 5 Output
Remark
Parking Lights Flash Once
1. Parking Lights Flash Twice
2. Dome Light Turns On for 30 Seconds
3. Porch Light Turns On for 30 Seconds
Note: If vehicle is operating from the RV
battery only, the parking lights will not flash.
Upon Vehicle's Door Unlock
C. Keypad Operation
Note: Turn the ignition switch to the "ON" position, or "LOCK" the vehicle's doors to turn off the dome light.
Keypad
Press the "LOCK" Key
Key in the "User
Code"
Press and Hold the
"1/2" Key for 3 Seconds
Press and Hold the
"3/4" Key for 3 Seconds
Key in the "User Code",
then Press and Hold
the "5/6" Key for 5
Seconds
Key in the "User Code",
then Press and Hold
the "7/8" Key for 5
Seconds
Key in the "User Code",
then Press and Hold
the "9/0" Key for 5
Seconds
© Copyright 2005 Magnadyne Corporation MKE-X-UM Rev. A 4-8-05