Magnadyne Keypad Keyless Entry System MKE-300A User manual

Antenna
LED
Program
Button
User's Manual
Keypad Keyless
Entry System
Models:
MKE-300A / MKE-400A
For Technical Assistance call [phone] or visit www.magnadyne.com
Programming
A. 3-Button Transmitter Programming
Note: This mode will only retain the last 4 remote
transmitters programmed. If the transmitter memory
is exceeded, the security system will start deleting
transmitters from memory in chronological order.
1. Turn the ignition switch to the "ON" position.
2. Within 15 seconds, push the Program Button
(located on back of the housing) 3 times. The
onboard LED will be flashing and the beeper will
emit a long chirp to indicate the system is in
Transmitter Programming mode.
3. Press and hold any button on the transmitter
until the onboard LED turns on for 2 seconds and
the beeper responds with a confirming chirp, indi-
cating the signal has been stored into memory.
4. If you have additional transmitters (up to 4)
that need to be programmed, repeat step 3 for
each transmitter.
Exit: Turn the ignition switch to the "OFF" position, or
leave it for 15 seconds. The onboard LED turns off
and the beeper will emit 3 long chirps to confirm exit.
B. 4-Button Transmitter Programming
Note: This mode will only retain the last 4 remote
transmitters programmed. If the transmitter memory
is exceeded, the security system will start deleting
transmitters from memory in chronological order.
1. Turn the ignition switch to the "ON" position
within 15 seconds.
2. Push the Program Button (located on back of
the housing) 5 times. The onboard LED will be
flashing and the beeper will emit a long chirp to
indicate the system is in Transmitter
Programming mode.
3. Press and hold any button on the transmitter
until the onboard LED turns on for 2 seconds and
the beeper responds with a confirming chirp, indi-
cating the signal has been stored into memory.
4. If you have additional transmitters (up to 4)
that need to be programmed, repeat step 3 for
each transmitter.
Exit: Turn the ignition switch to the "OFF" posi-
tion, or leave it for 15 seconds. The onboard LED
turns off and the beeper will emit 3 long chirps to
confirm exit.
Locks All Doors
(Including Cargo)
Locks All Doors
(Including Cargo)
Press Simultaneously to
Turn On / Off Porch Light
Locks All
Cargo Doors
Unlocks All
Cargo Doors
Unlocks Entry
Doors
Turns On / Off Porch Light
(Can be Programmed to
Unlock Cargo Doors)
Unlocks Entry
Doors
Unlocks Cargo Doors
(Can be Programmed to
Turn On / Off Porch Light)
Transmitters
Housing
MKE-34-UM.qxp 6/27/05 2:23 PM Page 1

Transmitter Button System Function
Locks the Vehicle's Doors and
Cargo Door
Unlocks the Vehicle's Doors
Locks the Cargo Door
Unlocks the Cargo Door
Turns the Porch Light "ON" or "OFF"
Remark
Parking Lights Flash Once
1. Parking Lights Flash Twice
2. Dome Light Turns On for 30 Seconds
3. Porch Light Turns On for 30 Seconds
Note: If vehicle is operating from the RV
battery only, the parking lights will not flash.
Upon Vehicle's Door Unlock
Operation
A. 4-Button Transmitter Operation
+
Transmitter Button System Function
Locks the Vehicle's Doors and
Cargo Door
Unlocks the Vehicle's Doors
Unlocks the Cargo Doors
(Can be reprogrammed to Turn the Porch Light
"ON" or "OFF")
Turns the Porch Light "ON" or "OFF"
(Can be programmed to Unlock the Cargo Doors)
Remark
Parking Lights Flash Once
1. Parking Lights Flash Twice
2. Dome Light Turns On for 30 Seconds
3. Porch Light Turns On for 30 Seconds
Note: If vehicle is operating from the RV
battery only, the parking lights will not flash.
Upon Vehicle's Door Unlock
Upon Vehicle's Door Unlock
B. 3-Button Transmitter Operation
© Copyright 2005 Magnadyne Corporation MKE-34A-UM Rev. A 6-27-05
+
System Function
Locks the Vehicle's Doors and
Cargo Door(s)
Unlocks the Vehicle's Doors
Locks or Unlocks the Cargo Door
(Operation is Sequential)
Turns On the Porch Light or Turns Off
the Porch Light (Operation is Sequential)
Activates the Channel 3 Output
Activates the Channel 4 Output
Activates the Channel 5 Output
Turns "ON" or "OFF" the Button Beep
Feature of the Keypad
Remark
Parking Lights Flash Once
1. Parking Lights Flash Twice
2. Dome Light Turns On for 30 Seconds
3. Porch Light Turns On for 30 Seconds
Note: If vehicle is operating from the RV
battery only, the parking lights will not flash.
Upon Vehicle's Door Unlock
C. Keypad Operation
Keypad
Press the "LOCK" Key
Key in the "User Code"
Press and Hold the
"1/2" Key for 3 Seconds
Press and Hold the
"3/4" Key for 3 Seconds
Key in the "User Code",
then Press and Hold
the "5/6" Key for 5
Seconds
Key in the "User Code",
then Press and Hold
the "7/8" Key for 5
Seconds
Key in the "User Code",
then Press and Hold
the "9/0" Key for 5
Seconds
Key in the "User Code",
then Press and Hold
the "LOCK" Key for 3
Seconds
C. Programming the User Code
(The default user code is "54321")
Note: This mode will only retain the last 4 "user
codes" programmed. If the user code memory is
exceeded, the security system will start deleting
user codes from memory in chronological order.
1. Enter the program code "12345" on the keypad.
The beeper will emit a long chirp to confirm the
correct code was entered.
2. Enter a new 4 to 6 digit user code on the keypad.
Do not use "1234".
3. Finish by pressing the "LOCK" key on the key-
pad. 1 long beep with 2 short beeps will confirm
the new user code has been stored into memory.
4. If you have additional user codes (up to 4) that
need to be programmed, repeat steps 2-3 for
each new user code.
Exit: Press and hold the "LOCK" key for 1 second or
if 15 seconds of inactivity occurs during the above
steps, the unit will revert back to the last success-
fully stored code. 3 longs beeps confirm exit.
D. Programming the Keypad Button Chirp On / Off.
1. Enter the user code.
2. Within 5 seconds, press and hold the LOCK
button for 3 seconds.
1 Beep from the keypad = Keypad Chirp "ON"
3 Beeps from the keypad = Keypad Chirp "OFF"
1 Beep = Keypad Chirp is "ON" (Default)
3 Beeps = Keypad Chirp is "OFF"
Programming (Continued) Operation (Continued)
MKE-34-UM.qxp 6/27/05 2:23 PM Page 2