Magnavox MDV435/77 User manual

User Manual
MDV435
MDV436
SMART. VERY SMART.
DIGITALVIDEO DISC PLAYER
01-31 MDV435_436_55_eng_RC2.indd 101-31 MDV435_436_55_eng_RC2.indd 1 2006-04-27 5:30:59 PM2006-04-27 5:30:59 PM

English
2
This product incorporates copyright protection
technology that is protected by method claims of
certain U.S. patents and other intellectual property
rights owned by Microvision Corporation and other
rights owners. Us eof this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
General Information
Environmental Information
All unnecessary packaging has been
omitted. The packaging has been made
easy to separate into three materials;
cardboard (box), polystyrene foam
(buffer) and polyethylene (bags,
protective foam sheet).
Your DVD player consists of materials
which can be recycled and reused if
disassembled by a specialised company.
Please observe the local regulations
regarding the disposal of packaging
materials, exhausted batteries and old
equipment.
(only for model MDV436)
Laser Safety
This unit employs a laser. Due to possible
eye injury, only a qualied service person
should remove the cover or attempt to
service this device.
NOTE:
Pictures shown maybe different
between countries.
CAUTION:
WARNING LOCATION: ON THE
BACKPLATE OF THE SET
NEVER MAKE OR CHANGE
CONNECTIONS WITH THE
POWER SWITCHED ON.
Manufactured under license from
Dolby Laboratories, “Dolby”
and the double-D symbol are
trademarks of Dolby Laboratories.
logo.indd 1 2006-03-21 10:25:36 AM
logo.indd 1 2006-03-21 10:25:36 AM
DivX Certied products: “DivX” and
associated logos are trademarks of
DivX, Inc. and are used under license.
01-31 MDV435_436_55_eng_RC2.indd 201-31 MDV435_436_55_eng_RC2.indd 2 2006-04-27 5:31:12 PM2006-04-27 5:31:12 PM

EnglishEspañolPortuguês
Index
English ------------------------------------------6
Português --------------------------------- 60
Español --------------------------------------- 32
LASER
Type Semiconductor laser
InGaAlP (DVD)
AIGaAs (CD)
Wave length 650 nm (DVD)
790 nm (CD)
Output Power 10.0 mW (DVD)
5.0 mW (VCD/CD)
Beam divergence 60 degrees
For Customer Use:
Read carefully the information located at
the bottom or rear of your DVD Video
player and enter below the Serial No.
Retain this information for future
reference.
Model No. MDV 435 & MDV 436
Serial No. ___________________
01-31 MDV435_436_55_eng_RC2.indd 301-31 MDV435_436_55_eng_RC2.indd 3 2006-04-27 5:31:13 PM2006-04-27 5:31:13 PM

English
4
Contents
Care and Safety Information
Setup................................................................................................................................................... 6
Cleaning discs................................................................................................................................... 6
General Information
Accessories supplied ...................................................................................................................... 7
Region codes .................................................................................................................................... 7
Connections
Connecting to television.............................................................................................8~9
Using Composite Video sockets (CVBS).................................................................................. 8
Using Component Video sockets (YPbPr)............................................................................... 8
Using an accessory RF modulator .............................................................................................. 9
Connecting the power cord............................................................................................ 9
Optional connections
Connecting to an stereo system.................................................................................. 10
Stereo system has Right/Left Audio In sockets....................................................................10
Connecting to a digital AV receiver ............................................................................ 10
Receiver has a PCM, Dolby Digital or MPEG decoder....................................................... 10
Product Overview
Front and Rear panels ....................................................................................................11
Remote Control ............................................................................................................. 12
Getting Started
Step 1: Inserting Baterries ........................................................................................... 13
Using the remote control to operate the system................................................................13
Step 2: Finding your viewing channel.......................................................................... 13
Step 3: Setting up Progressive Scan feature ..............................................................14
Step 4: Selecting the matching colour system .......................................................... 15
Step 5: Setting the language ........................................................................................ 16
On-screen display (OSD) language .......................................................................................... 16
Audio, Subtitle and Disc menu languages............................................................................... 16
Playback from Disc
Playable discs...................................................................................................................17
Supported formats........................................................................................................................ 17
Playback Features
Starting disc playback ................................................................................................... 18
Basic playback control .................................................................................................. 18
Pausing playback ............................................................................................................................ 18
Selecting title/chapter/track.......................................................................................................18
Stopping playback..........................................................................................................................18
Operations for video playback (DVD/VCD/SVCD) .................................................. 19
Using the Disc Menu .................................................................................................................... 19
Zooming in...................................................................................................................................... 19
OSD (On-Screen Display).......................................................................................................... 19
Selecting various repeat / shufe functions ............................................................... 20
Repeat play mode..........................................................................................................................20
Repeating a section within a chapter/track............................................................................20
01-31 MDV435_436_55_eng_RC2.indd 401-31 MDV435_436_55_eng_RC2.indd 4 2006-04-27 5:31:13 PM2006-04-27 5:31:13 PM

English
5
Contents
Special DVD Features ............................................................................................. 20~21
Playing a Title..................................................................................................................................20
Camera Angle.................................................................................................................................20
Changing the Audio Language.................................................................................................... 21
Subtitle ............................................................................................................................................. 21
Special VCD and SVCD Feature.................................................................................. 21
Playback Control (PBC) .............................................................................................................. 21
Playing a DivX disc (optional) ..................................................................................................... 21
Playing MP3/JPEG/Kodak Picture CD ........................................................................ 22
General Operation.......................................................................................................................22
Playback selection .........................................................................................................................22
Repeat ..............................................................................................................................................22
DVD Menu Options
Using the System setup menu ...............................................................................23~24
TV System .......................................................................................................................................23
TV Type............................................................................................................................................23
Password .........................................................................................................................................24
Rating................................................................................................................................................24
Default..............................................................................................................................................24
Using the Language setup menu ................................................................................. 25
OSD Language................................................................................................................................25
Audio, Subtitle and Disc Menu Languages..............................................................................25
Setting the DivX Subtitle font (optional)........................................................................................25
DivX(R) registration code (optional)..............................................................................................25
Using the Audio setup menu........................................................................................ 26
Digital Out ......................................................................................................................................26
Down Sample .................................................................................................................................26
Downmix.........................................................................................................................................26
Using the Video setup menu ........................................................................................ 27
Video Out........................................................................................................................................27
Brightness / Contrast...................................................................................................................27
Hue....................................................................................................................................................27
Saturation........................................................................................................................................27
Sharpness.........................................................................................................................................27
Others
Troubleshooting .......................................................................................................28~29
Specications ................................................................................................................. 30
Glossary .......................................................................................................................... 31
01-31 MDV435_436_55_eng_RC2.indd 501-31 MDV435_436_55_eng_RC2.indd 5 2006-04-27 5:31:13 PM2006-04-27 5:31:13 PM

English
6
Care and Safety Information
DANGER!
High voltage! Do not open
the device. You run the risk of
getting an electric shock.
The machine does not contain any
user-serviceable parts. Please leave
all maintenance work to qualied
personnel.
Setup
Finding a suitable location
– Place the set on a at, hard and stable
surface. Do not place the set on a
carpet.
– Do not position the set on top of
other equipment that might heat it up
(e.g., receiver or amplier).
– Do not put anything under the set
(e.g., CDs, magazines).
– Install this unit near the AC outlet and
where the AC power plug can be
reached easily.
Space for ventilation
– Place the apparatus in a location with
adequate ventilation to prevent
internal heat build up. Allow at least
10 cm (4.0”) clearance from the rear
and the top of the set and 5cm (2.0”)
from the left and right to prevent
overheating.
10cm (4.0") 10cm (4.0")
5cm (2.0")
5cm (2.0")
Avoid high temperatures, moisture,
water and dust
– Apparatus shall not be exposed to
dripping or splashing.
– Do not place any sources of danger
on the apparatus (e.g., liquid lled
objects, lighted candles).
Cleaning discs
Some problems occur because the disc
inside the recorder is dirty (frozen
picture, sound disruptions, picture
distortions). To avoid these problems,
discs should be cleaned on a regular
basis.
To clean a disc, use a micro bre cleaning
cloth and wipe the disc from the center
to the edge in a straight line.
CAUTION!
Do not use solvents such as benzene,
thinner, commercially available cleaners,
or anti-static sprays intended for analog
discs. Since the optical unit (laser) of the
DVD recorder operates at a higher
power than regular DVD or CD players,
cleaning CDs intended for DVD or CD
players may damage the optical unit
(laser). Therefore, refrain from using a
cleaning CD.
01-31 MDV435_436_55_eng_RC2.indd 601-31 MDV435_436_55_eng_RC2.indd 6 2006-04-27 5:31:13 PM2006-04-27 5:31:13 PM

English
7
General Information
Accessories supplied
ALL
4
Region
U.S.A. and
Canada regions
U.K and
Europe regions
Asia Pacic,
Taiwan, Korea
Australia,
New Zealand,
Latin America
Russia and
India regions
China, Calcos Islands,
Walls and Futuna
Islands
ALL
ALL
5
6
Discs that can
be played
ALL
1
ALL
ALL
2
3
Remote
control and
two AAA
batteries
Region codes
This DVD player is designed to support
the Region Management System. Check
the regional code number on the disc
package. If the number does not match
the player’s region number (see table
below), the player may be unable to
playback the disc.
Tips:
– It may not be possible to play CD-R/RW
or DVD-R/RW in all cases due to the type of
disc or condition of the recording.
– If you are having trouble playing a certain
disc, remove the disc and try a different one.
Improper formatted disc will not played on
the DVD player.
Audio cable
(white, red)
Video cable
(yellow)
01-31 MDV435_436_55_eng_RC2.indd 701-31 MDV435_436_55_eng_RC2.indd 7 2006-04-27 5:31:13 PM2006-04-27 5:31:13 PM

English
8
Connections
Connecting to television
IMPORTANT!
– You only need to make one video
connection from the following
options, depending on the
capabilities of your television.
– Connect the DVD player directly
to the television.
Using Composite Video sockets
(CVBS)
AUse the composite video cable (yellow)
to connect the DVD player’s CVBS
(VIDEO) socket to the video input jack
(or labeled as A/V In, Video In,
Composite or Baseband) on the
television (cable supplied).
BTo hear sound of this DVD player
through your TV, use the audio cables
(white/red) to connect AUDIO OUT (L/
R) sockets of the DVD player to the
corresponding AUDIO IN sockets on the
television (cable supplied).
AUDIO OUT
DIGITAL
OUT VIDEO OUT
COAXIAL
AUDIO
IN
V (Pr/Cr)
U (Pb/Cb)
Y
S-VIDEO
IN
VIDEO IN
COMPONENT
VIDEO IN
AUDIO
OUT
V(Pr/Cr)
U(Pb/Cb)
Y
S-VIDEO
IN
VIDEOIN
COMPONENT
VIDEOIN
21
IMPORTANT!
– The progressive scan video quality
is only possible when using YPbPr
and a progressive scan television is
required.
Using Component Video sockets
(YPbPr)
AUse the component video cables (red/
blue/green) to connect the DVD player’s
YPbPr sockets to the component video
input sockets (or labeled as YPbPr) on
the television (cable not supplied).
BTo hear sound of this DVD player
through your TV, use the audio cables
(white/red) to connect AUDIO OUT (L/
R) sockets of the DVD player to the
corresponding AUDIO IN sockets on the
television (cable supplied).
CProceed to page 14 for detailed
progressive scan setup.
TIPS: Before making or changing any connections, make sure that all the devices are disconnected from
the power outlet.
01-31 MDV435_436_55_eng_RC2.indd 801-31 MDV435_436_55_eng_RC2.indd 8 2006-04-27 5:31:14 PM2006-04-27 5:31:14 PM

English
9
Connections (continued)
AUDIO OUT
DIGITAL
OUT VIDEO OUT
COAXIAL
AUDIO IN
R L
VIDEO
IN
TO TVINT IN
CH3 CH4
1
RF coaxial cable to TV
Back of RF Modulator
(example only)
IMPORTANT!
– If your television only has a single
Antenna In jack (or labeled as 75
ohm or RF In,) you will need an RF
modulator in order to view the
DVD playback on the television. See
your electronics retailer for details
on RF modulator availability and
operations.
Using an accessory RF modulator
AUse the composite video cable (yellow)
to connect the DVD player’s CVBS jack
to the video input jack on the RF
modulator.
BUse the RF coaxial cable (not supplied) to
connect the RF modulator to your
television’s RF jack.
CTo hear sound of this DVD player
through your TV, use the audio cables
(white/red) to connect AUDIO OUT (L/
R) sockets of the DVD player to the
corresponding AUDIO IN sockets on the
RF modulator (cable supplied).
TIPS: Before making or changing any connections, make sure that all the devices are disconnected from
the power outlet.
AUDIO OUT
DIGITAL
OUT VIDEO
O
COAXIAL
~ AC MAINS
AUDIO
OUT
V(Pr/Cr)
U(Pb/Cb)
Y
S-VIDEO
IN
VIDEOIN
COMPONENT
VIDEOIN
Connecting the power cord
After everything is connected
properly, plug in the AC power cord
to the power outlet.
Never make or change any connections
with the power switched on.
When no disc is loaded, press
STANDBY ON on the DVD player
front panel.
“NO DISC” may appear on the
display panel.
01-31 MDV435_436_55_eng_RC2.indd 901-31 MDV435_436_55_eng_RC2.indd 9 2006-04-27 5:31:14 PM2006-04-27 5:31:14 PM

English
10
AUDIO OUT
DIGITAL
OUT VIDEO OUT
COAXIAL
AUDIO
IN
STEREO
DIGITAL
Connecting to an stereo
system
AUDIO OUT
DIGIT
AL
OUT VIDEO OUT
COAXIAL
AUDIO
IN
DIGITAL
AV
R eciever
Receiver has a PCM, Dolby Digital
or MPEG decoder
ASelect one of the video connections
(CVBSVIDEO IN, COMPONENT VIDEO
IN) depending on the options available on
your TV.
BConnect the COAXIAL jack of the DVD
player to the corresponding Digital Audio
In socket on your receiver (cable not
supplied).
CSet the DVD player’s digital output to
PCM or ALL depending on the
capabilities of your receiver (see page 26
{Digital Out}).
Tip:
– If the audio format of the Digital Output
does not match the capabilities of your
receiver, the receiver will produce a strong,
distorted sound or no sound at all.
Stereo system has right/ left Audio
In sockets
ASelect one of the video connections
(CVBSVIDEO IN, COMPONENT VIDEO
IN) depending on the options available on
your TV.
BUse the audio cables (white/red) to
connect AUDIO OUT (L/R) sockets of
the DVD Player to the corresponding
AUDIO IN sockets on the stereo system
(cable supplied).
Connecting to a digital AV
receiver
Optional connections
TIPS: Before making or changing any connections, make sure that all the devices are disconnected from
the power outlet.
01-31 MDV435_436_55_eng_RC2.indd 1001-31 MDV435_436_55_eng_RC2.indd 10 2006-04-27 5:31:14 PM2006-04-27 5:31:14 PM

English
11
Product Overview
TIPS: Before making or changing any connections, make sure that all the devices are disconnected from
the power outlet.
Front and Rear Panels
AUDIO OUT
DIGITAL
OUT VIDEO OUT
COAXIAL
STANDBY-ON
– Turns on the player or switches
to standby mode
Disc Tray
OPEN/CLOSEç
– Opens or closes the disc tray.
Display panel
– Shows information about the
current status of the DVD player.
Mains (AC Power Cord)
– Connect to a standard AC outlet
Audio Out (Left/Right)
– Connect to AUDIO inputs of an
amplier, receiver or stereo
system
COAXIAL (Digital audio out)
– Connect to coaxial AUDIO input
of a digital audio equipment
ÅPLAY/PAUSE
– Starts or interrupts playback.
STOP
– Stops playback
IR Sensor
– Point the remote control towards
this sensor
YPbPr (Component Video Out)
– Connect to YPbPr input of a TV
CVBS (VIDEO Out)
– Connect to CVBS Video input
of a TV
01-31 MDV435_436_55_eng_RC2.indd 1101-31 MDV435_436_55_eng_RC2.indd 11 2006-04-27 5:31:14 PM2006-04-27 5:31:14 PM

English
12
Product Overview (continued)
Remote Control
OPEN/CLOSE
– Opens or closes the disc tray
0-9 numeric key pad
– Selects numbered items in a
menu
RETURN/TITLE
– To go back to previous
menu/ show title menu
DISC MENU
– Enters or exits the disc
contents menu
– Switches on or off the
playback control mode (for
VCD version 2.0 only)
.
– Skip to previous title/
chapter/ track
>
– Skip to next title/ chapter/
track
SUBTITLE
– To access subtitle language
system menu
AUDIO
– Selects an audio language
(DVD/VCD) or an audio
channel
ANGLE
– Selects a DVD camera angle
ZOOM
– Enlarge a picture on the TV
screen
DISPLAY
– Displays information on TV
screen during playback
1POWER
– To switch the DVD player
to standby mode or ON
SEARCH
– To start playback from
designated point
SETUP
– Enters or exits the system
setup menu
   
– Selects an item in the
menu/ fastforward/
backward
OK
– Acknowledge menu
selection
STOP
– Stops playback
Å PLAY/PAUSE
– Starts or pauses playback
MUTE
– Disables or enables sound
output
REPEAT
– Selects various repeat
mode
REPEAT A-B
– Repeats playback a specic
section on a disc
PREVIEW
– To browse tracks
STEP
– Play the video frame by
frame
01-31 MDV435_436_55_eng_RC2.indd 1201-31 MDV435_436_55_eng_RC2.indd 12 2006-04-27 5:31:14 PM2006-04-27 5:31:14 PM

English
13
Getting Started
Step 1 : Inserting Batteries
AOpen the battery compartment.
BInsert two batteries type R03 or AAA,
following the indications (+ –) inside the
compartment.
CClose the cover.
CAUTION!
– Remove batteries if they are
exhausted or if the remote is not to
be used for a long time.
– Do not use old and new or
different types of batteries in
combination.
– Batteries contain chemical
substances, so they should be
disposed of properly.
Using the remote control to
operate the system
AAim the remote control directly at the
remote sensor (IR) on the front panel.
BDo not put any objects between the
remote control and the DVD player
while operating the DVD player.
Step 2 : Finding your viewing
channel
APress STANDBY-ON 2on the DVD
player to turn it on.
BTurn on the TV and set it to the correct
video-in channel. You should see the blue
DVD background screen.
Usually these channel are between the
lowest and highest channels and may
be called FRONT, A/V IN, VIDEO.
See your TV’s manual for more
details.
Or, you may go to channel 1 on your
TV, then press the Channel down
button repeatedly until you see the
Video In channel.
Or, the TV remote control may have
a button or switch that chooses
different video modes.
Or, set the TV to channel 3 or 4 if
you are using an RF modulator.
CIf you are using external equipment, (e.g.
audio system or receiver), turn it on and
select the appropriate input source for
the DVD player output. Refer to the
equipment user’s manual for detail.
01-31 MDV435_436_55_eng_RC2.indd 1301-31 MDV435_436_55_eng_RC2.indd 13 2006-04-27 5:31:15 PM2006-04-27 5:31:15 PM

English
14
Getting Started (continued)
Step 3 : Setting up
Progressive Scan feature
(for Progressive Scan TV only)
The progressive scan displays twice the
number of frames per seconds than
interlaced scanning (ordinary normal TV
system). With nearly double the number
of lines, progressive scan offers higher
picture resolution and quality.
Before you start...
– Ensure that you have connected this
DVD player to a progressive scan TV
using the Y Pb Pr connection (see page
8).
– Ensure that you have completed the
basic installation and set-up.
ATurn on your TV and set to interlace
mode (refer to your TV user manual).
BPress POWER on the remote control
to turn on the DVD player.
CSelect the correct video-in channel.
 The DVD background menu appears.
DPress SETUP.
EPress to select { VIDEO SETUP }
FPress repeatedly to select
{ VIDEO OUT }.
VIDEO SETUP
VIDEO OUT
BRIGHTNESS
CONTRAST
HUE
SATURATION
SHARPNESS
EXIT SETUP
INTERLACE-YUV
P -SCAN YPBPR
GPress to select { P-SCAN YPBPR },
then press OK.
 The menu will appear on the TV.
TIPS: The underlined option is the factory default setting.
Press to go back to previous menu item. Press SETUP to exit the menu item.
ENABLE PROGRESSIVE
OK
ENSURE YOUR TV SUPPORTS PSCAN
IF TV DISPLAY IS ABNORMAL
PLEASE WAIT 15 SECONDS
FOR IT TO RECOVER
NO
HPress to select { OK } and press OK
to conrm.
There will be a distorted picture on
the TV at this state until you turn
on the progressive scan mode on
your TV.
ITurn on your TV progressive scan mode
(refer to your TV user manual).
 The menu will appear on the TV.
PROGRESSIVE SCAN
OK
YOUR PROGRESSIVE SCAN IS ON
DO YOU WANT TO KEEP THE
CURRENT SETTING
PLEASE WAIT 15 S
NO
JPress to select { OK } and press OK
to conrm.
 The setup is now completed and you
can start enjoy the high quality
picture.
To deactivate Progressive Scan
manually:
 Wait for 15 seconds for auto recovery.
Tip:
– There are some progressive scan TVs and
High-Denition TVs that are not fully
compatible with this unit, resulting in the
unnatural picture when playing back a DVD
VIDEO disc in the progressive scan mode. In
such a case, turn off the progressive scan
feature on both the DVD player and your TV.
01-31 MDV435_436_55_eng_RC2.indd 1401-31 MDV435_436_55_eng_RC2.indd 14 2006-04-27 5:31:15 PM2006-04-27 5:31:15 PM

English
15
Getting Started (continued)
Step 4 : Selecting the
matching colour system
The colour system of the DVD player,
disc and TV should match in order for
the disc to play. Before changing the TV
system, determine the colour system of
your TV.
SYSTEM SETUP
TV SYSTEM
TV TYPE
PASSWORD
RATING
DEFAULT
EXIT SETUP
NTSC
PAL
MULTI
APress SETUP.
BPress WXto select { SYSTEM
SETUP }.
CPress STto select { TV SYSTEM },
then press X.
DUse STto select one of the options
below:
{ PAL }
Select this if the connected TV has the
PAL colour system. It will change the
video signal of an NTSC disc and output
it to PAL format.
{ NTSC }
Select this if the connected TV has the
NTSC colour system. It will change the
video signal of a PAL disc and output it to
NTSC format.
{ MULTI }
Select this if the connected TV is
compatible with both NTSC and PAL
(multi-system). The output format will be
in accordance with the video signal of the
disc.
ESelect an item and press OK.
Tip:
– Before changing the current TV colour
setting, ensure that your TV supports the
‘selected TV System’.
CHANGING PAL TO NTSC:
NO
1 . ENSURE THAT YOUR TV
SUPPORTS NTSC STANDARD.
2 . IF THERE IS DISTORTED
PICTURE DISPLAY ON THE TV
WAIT 15S FOR AUTO RECOVERY.
OK
CONFIRM AGAIN TO USE NEW TV
TYPE SETTING.
PLEASE WAIT 15 S
NO
OK
TIPS: The underlined option is the factory default setting.
Press Wto go back to previous menu item. Press SETUP to exit the menu item.
01-31 MDV435_436_55_eng_RC2.indd 1501-31 MDV435_436_55_eng_RC2.indd 15 2006-04-28 10:38:36 AM2006-04-28 10:38:36 AM

English
16
Getting Started (continued)
Step 5 : Setting the language
The language options are different
depending on your country or region. It
may not correspond to the illustrations
shown on the user manual.
On-screen display (OSD) language
Select this to change the language of this
DVD player screen display menu.
The menu language (on-screen display)
for the system will remain as you set it.
LANGUAGE SETUP
OSD LANGUAGE
AUDIO LANG
SUBTITLE LANG
DISC MENU
DIVX SUBTITLE
DIVX(R) VOD
EXIT SETUP
ENGLISH
APress SETUP.
BPress to select { LANGUAGE
SETUP }.
CPress to highlight { OSD
LANGUAGE }, then press .
DUse to select a language and press
OK.
TIPS: The underlined option is the factory default setting.
Press to go back to previous menu item. Press SETUP to exit the menu item.
Audio, Subtitle and Disc menu
languages
You can choose your preferred language
or soundtrack from audio, subtitles and
DVD menu languages. If the selected
language is not available on the disc, the
disc’s default language will be used
instead.
LANGUAGE SETUP
OSD LANGUAGE
AUDIO LANG
SUBTITLE LANG
DISC MENU
DIVX SUBTITLE
DIVX(R) VOD
EXIT SETUP
CHINESE
ENGLISH
JAPANESE
FRENCH
SPANISH
PORTUGUESE
LATIN
GERMAN
APress SETUP.
BPress to select { LANGUAGE
SETUP }.
CPress to highlight one of the
options below, then press .
{ AUDIO LANG }
Select this to change disc soundtrack
language.
{ SUBTITLE LANG }
Select this to change the subtitle language.
{ DISC MENU }
Select this to change the language of the
disc menu.
DUse to select a language and press
OK to conrm.
ERepeat steps C- Dfor other language
settings.
Tip:
– Audio Lang and Subtitle Lang can only be
activated during disc ejecting or no disc
mode.
Tip: DivX is an option for certain models only.
01-31 MDV435_436_55_eng_RC2.indd 1601-31 MDV435_436_55_eng_RC2.indd 16 2006-04-27 5:31:16 PM2006-04-27 5:31:16 PM

English
17
Playback from Disc
IMPORTANT!
– If the INVALID ENTRY appears
on the TV screen when a button is
pressed, it means the function is not
available on the current disc or at
the current time.
– DVD discs and players are designed
with regional restrictions. Before
playing a disc, make sure the disc is
for the same zone as your player.
Playable discs
Using this DVD player, you can playback
on the following discs:
DVD Video (Digital Versatile
Disc)
DVD±RW (DVD Rewritable)
Audio/Video format or
MP3/JPEG/DivX les.
DVD±R (DVD Recordable)
Audio/Video format or
MP3/JPEG/DivX les.
CD-R (CD-Recordable)
Audio/Video format or
MP3/JPEG/DivX les.
CD-RW (CD-Rewritable)
Audio/Video format or
MP3/JPEG/DivX les.
Audio CD (Compact Disc
Digital Audio)
Video CD
(Formats 1.0, 1.1, 2.0)
TIPS: Some discs cannot be played on this DVD player due to the conguration and characteristics of the disc, or
due to the condition of recording and authoring software that was used.
Super Video CD
MP3-Disc
DivX Disc
(DivX 3.11, 4.x, 5.x and 6.x)
Supported formats
MP3 tracks
– The le extensions has to be ‘.mp3.’
– JPEG/ISO format
– Maximum 10 characters display.
– Supported sampling frequencies;
(MPEG-1) 32kHz, 44.1kHz, 48kHz
(MPEG-2) 16kHz, 22.05kHz, 24kHz
– Supported bit-rates;
(MPEG-1) 32 ~ 256 kbps
(MPEG-2) 16 ~ 160 kbps
JPEG pictures
– The le extensions has be to be ‘.JPG’
and not ‘.JPEG.’
– JPEG/ISO format
– It can only display DCF-standard still
pictures or JPEG pictures e.g. TIFF.
DivX movies
– The le extensions has be to be ‘.AVI,’
‘.MPG,’ or ‘.MPEG.’
– DivX 3.11, 4.x, 5.x and 6.x
– Q-pel accurate motion compensation
– Global Motion Compensation (GMC)
playback.
Tip: DivX is an option for certain models only.
01-31 MDV435_436_55_eng_RC2.indd 1701-31 MDV435_436_55_eng_RC2.indd 17 2006-04-27 5:31:17 PM2006-04-27 5:31:17 PM

English
18
Playback Features
Starting disc playback
ATurn on the TV to the correct
programme number for the DVD player
(e.g. ‘EXT’, ‘0’, ‘AV’).
BPress STANDBY-ON to turn on the
DVD player.
CPress OPEN/CLOSE on the front of
the DVD player.
DPlace a disc into the disc tray with the
label facing up, then press OPEN
CLOSE ç.
 For double-sided discs, load the side
which you want to play facing up.
EPlayback may start automatically.
If not, press PLAY/PAUSE Å.
If a disc menu appears on the TV, see
page 19 'Using the Disc Menu'.
If the child lock was activated for the
inserted disc, you have to enter your
four-digit password (see page 24).
For more playback features, see pages
18~21.
Basic playback controls
Unless otherwise stated, all operations
described are based on Remote Control
use.
Pausing playback
ADuring playback, press PLAY/PAUSE
Å to pause playback and display a still
picture.
 Sound will be muted.
BTo resume normal playback, press
PLAY/PAUSE Å again.
Selecting title/chapter/track
Press ./ >to go to the previous
or next title/chapter/track.
In STOP mode, press DISPLAY to
display the disc information text line for
title/chapter/track (example - 00/08).
Use alphanumeric keypad (0-9) to
enter valid title/chapter/track number.
 The playback skips to the selected
title/chapter/track.
Stopping playback
Press STOP .
Tips:
– Screen saver will start automatically if the
disc playback is stopped for 5 minutes.
– The player will automatically switch to
Power Standby mode if you do not press any
buttons for 10 minutes after the disc has
stopped playing.
TIPS: The operating features described here might not be possible for certain discs.
Always refer to the instructions supplied with the discs.
01-31 MDV435_436_55_eng_RC2.indd 1801-31 MDV435_436_55_eng_RC2.indd 18 2006-04-27 5:31:18 PM2006-04-27 5:31:18 PM

English
19
Playback Features (continued)
Operations for video
playback (DVD/VCD/SVCD)
Using the Disc Menu
Depending on the disc, a menu may
appear on the TV screen once you load
in the disc.
To select a playback feature or item
 Use keys or numeric keypad
(0-9) on the remote, then press OK to
start playback.
To access or remove the menu
Press DISC MENU on the remote.
Zooming in
This function allows you to enlarge the
picture on the TV screen and to pan
through the enlarged picture.
ADuring playback, press ZOOM
repeatedly to display the picture with
different scales.
 Use keys to pan through
the enlarged picture.
 Playback will continue.
BPress ZOOM repeatedly to return to
the original size.
OSD (On-Screen Display)
This function display disc information on
the TV screen during playback.
ADuring playback, press DISPLAY
repeatedly.
 A list of available current disc
information appears on the TV
screen.
BPress SEARCH, then use keys to
select an option.
Enter hours, minutes and seconds from
left to right in the time edit box using
remote control numerical key pad.
Playback will change to the chosen time
or to the selected title/ chapter/ track.
For DVD
 {TT XX/03 CH XXX/010}: displays
the total available title and chapters in
the disc and enable to select a chapter
for viewing.
 {XXX:XX:XX} displays the total
available title in the disc and enable to
select the hour, minute and second of
the title.
For Super VCD or VCD
 {XXX:XX:XX}: enable to select any
part within the disc.
 {TRK XX/XX}: enable to select any
track.
TIPS: The operating features described here might not be possible for certain discs.
Always refer to the instructions supplied with the discs.
01-31 MDV435_436_55_eng_RC2.indd 1901-31 MDV435_436_55_eng_RC2.indd 19 2006-04-27 5:31:18 PM2006-04-27 5:31:18 PM

English
20
Playback Features (continued)
Repeating a section within a
chapter/track
You can repeat the playback of a specic
segment within a title/chapter track. To
do this, you must mark the start and end
of the segment you want.
AWhile playing a disc, press REPEAT A-
Bat your chosen starting point.
BPress REPEAT A-B again at your
chosen end point.
 The section A and B can be set only
within the same chapter/track.
 The section will now repeat
continuously.
CTo exit the sequence, press REPEAT
A-B.
Selecting various repeat/
shufe functions
Repeat play mode
The repeat play options vary depending
on the disc type.
AWhile playing a disc, press REPEAT
continuously to choose a repeat options.
CHAPTER (DVD)
– to repeat playback of the current
chapter.
REP I (CD/ SVCD/ VCD) /
TITLE (DVD)
– to repeat playback of the current
track (CD/ SVCD/ VCD) / title.
REP ALL
– to repeat playback of the disc.
RANDOM (CD/ VCD)
– the tracks and chapters being played
in random order.
OFF
– to cancel the repeat mode.
BPress REPEAT repeatedly to cancel the
repeat mode.
Tip:
– For VCD, repeat playback is not possible if
the PBC mode is switched on.
TIPS: The operating features described here might not be possible for certain discs.
Always refer to the instructions supplied with the discs.
Special DVD Features
Playing a Title
APress DISC MENU.
The disc title menu appears on the TV
screen.
BUse keys or alphanumeric
keypad 0-9 to select a play option.
CPress OK key to conrm.
Camera Angle
Press ANGLE repeatedly to select
different desired angle.
01-31 MDV435_436_55_eng_RC2.indd 2001-31 MDV435_436_55_eng_RC2.indd 20 2006-04-27 5:31:18 PM2006-04-27 5:31:18 PM