Magnavox MDV560VR - Dvd/vcr Player Operating manual

VCR IN
LINE 1 DVD/VCR
OUT AUDIO
OUT
AUDIO AUDIO
VIDEO VIDEO COAXIAL
DVD EXCLUSIVE OUT
DVD/VCR
OUT
ANT IN
RF. OUT DVD EXCLUSIVE
OUT
REAR OFTV
(EXAMPLE ONLY)
ANTENNA IN
4
IN OUT
RF COAXIAL CABLE
CABLE
TV SIGNAL
ANTENNA or
CABLETV SIGNAL
CABLE BOX OR
2
3
1Disconnect all equipment from the power outlets. Connect the equipment to the power outlets only after you
have finished hooking up everything. Never make or change connections with equipment connected to the power outlet.
2If you do not have a Cable Box, simply connect yourAntenna or CableTV signal directly to theANT-IN jack
on the rear of the DVD/VCR.
If you do have a Cable Box (or Satellite Receiver),first connect the CableTV (or Satellite) signal to the IN
jack on the Cable Box/Satellite Receiver. Then,use an RF coaxial cable (like the one supplied) to connect the
OUT jack of the Cable Box/Satellite Receiver to theANT-IN jack on the DVD/VCR.
3Connect the supplied black RF coaxial cable to the DVD/VCR’s RF-OUT jack and to yourTV’sANTENNA IN
jack. The TV’s ANTENNAIN jack could be labelled 75-ohm, TV IN, or RF IN. Check your TV manual for details.
4Plug the power cords of the DVD/VCR and theTV into an active power outlet.
5Turn on theTV power. Set theTV to channel 3. (If you cannot use channel 3 at your TV, you can use channel 4
instead. However, you must set the DVD/VCR’s RF output channel to 4. See the accompanying DVD/VCR owner’s
manual for details.)
6Press the STANDBY 2button on the DVD/VCR or the POWER 2button on its remote to turn on the
DVD/VCR. The first time you turn on the DVD/VCR, you should set up yourTV channels at theVCR. See
the other side of this Quick-Use Guide for details.
MDV560VR
There are many ways to connect your new DVD/VCR to yourTelevision and other equipment.This Quick-Use
Guide shows the easiest, most common connection between the DVD/VCR and aTV.
Higher quality connections are explained in the owner’s manual and will provide better sound or picture if your
TV and/or audio system is compatible.
8239 300 31711

Quick-Use Guide (cont’d)
Quick-Use Guide (cont’d)
Detailed playback features and additional functions are described in the
accompanying owner’s manual.
Playing a Disc
1With theTV and DVD/VCR on, press the DVD
button to put the DVD/VCR in DVD mode.
2Press OPEN/CLOSE /to open the disc tray. Put
a Disc in the tray with the label facing up and the
shiny side facing down.
Press OPEN/CLOSE /again to close the tray.
3Playback may start automatically. If not, press
PLAY. If a DVD Disc menu appears, use the 1 234,
OK, or Number buttons to select features or start
playback. Follow the instructions in the menu.
4To stop playing the Disc, press STOP.
3840R-Q004N
MDV560VR / 8239 300 31711
Printed in Indonesia
SettingTV Channels at theVCR
1Turn on theTV and set it to channel 3.
2Press POWER 2to turn on the DVD/VCR.
3Press VCR to put the unit in VCR mode. Then, press
SYSTEM MENU.
4Press 3or 4to select the TUNING menu, then press
OK.
5AUTO CHANNEL SET will be selected at the top of
the menu. Press 1or 2to start automatic channel
setup.
6When channel setup is complete, the unit will go to the
lowest availableTV channel automatically.The
DVD/VCR is ready for use!
Playable Discs
The DVD Player of the DVD/VCR will play the following Discs.
DVDs must have a Region Code of ALL regions or Region 1.
DVDs must be recorded in the NTSC Color System.
1
ALL
Turn on
theTV to
channel 3.
4-5
4
LABEL
1
2
3
2
3
1
3