Magnavox MD6972 User manual

WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, AND ANNOYING INTERFERENCE, USE
THE RECOMMENDED ACCESSORIES ONLY.

this unit may not have the capability to be connected to an outdoor antenna.
For example,

eight (8)
eight (8)
AC 120V~;
AC 120V~; 60Hz
60Hz "C" size batteries (not included)
"C"
7. Clean the batttery contacts and also those of the device prior to battery installation.

21
1
2
3
4
56 7 8 9 10
13
12
11
14 15
20
17
18
19
$& ,1a
16
1. FM Telescope Antenna
2. Carry Handle
3. VOLUME Control Knob
4. Decorative LED Blinking Mode
Selection (Turn Off) Button
5. M (Memory) Button
6. /BAND (Stop/Radio Band
Selection) Button
7. (Skip/Fast Search Backward)
Button
8. (Skip/Fast Search Forward)
Button
9. /SCAN (Play - Pause/Radio
Scan) Button
10. BT/CD (Bluetooth/CD Mode
Selection) Button
11. CD Door
12. FINE TUNE (Radio Fine Tune)
Knob
13. CD Door OPEN/CLOSE Area
14. POWER Indicator
15. LCD Display
16. (Bluetooth) Indicator
17. Function Selector (Radio –
BT/CD/AUX – Power Off)
18. AUX (In) Jack
19. (Headphone/Earphone) Jack
20. AC~ Socket
21. Battery Compartment
LOCATION OF CONTROLS

8
RADIO:
1. Slide the Function Selector to RADIO position to turn on the radio.
2. Press the /BAND Button repeatedly to select AM or FM band as desire. The correspondence
indicator AM or FM and the radio frequency will appear on the LCD Display.
3. Press and holding the or Buttons until the radio frequency on the LCD Display start
running to automatically search and play the previous/next available radio station. Repeated the
same procedures until the desired radio station is searched and play.
4. If the reception is no good, turn the FINETUNE Knob to fine tune.
5. Turn the VOLUME Control Knob to adjust volume level as desire.
6. When finished listening, slide the Function Selector to OFF position to power of the unit.
Radio stations preset:
1. Power on the radio and receive the desired radio station as the previously procedure.
2. Press the M Button, "P XX" will appear on the LCD Display. Press the or Buttons
repeatedly to select the program number you want stored to. Then press the M Button again to
store it.
3. Repeat the same procedures until all the desired radio stations were stored into the program list.
(Up to 20 AM stations and 30 FM stations can be stored.)
4. After programmed, press the or Buttons repeatedly in radio mode to select and play the
desired stored radio station.
Antennas:
AM:
This unit has a built-in ferrite rod antenna, which provides adequate reception in most areas. If
reception is weak, turn the unit to improve reception.
FM:
The FM Telescopic Antenna is for FM reception only. If reception is weak, adjust the length and the
angle of the antenna.
CD:
1. Slide the Function Selector to BT/CD/AUX position to turn on the CD.The LCD Display will
illuminate and indicator “CD” will appear.
2. Press the OPEN/CLOSE Area on the CD Door to open it then place a CD disc on the center
spindle, with the printed side face up.
OPERATION

9
3. Close the CD door by press the OPEN/CLOSE Area. Wait a few seconds; the number of the total
tracks will appear on the LCD Display.
4. Press the /SCAN Button to start playback the first track on the disc.
5. During playback:
Turn the VOLUME Control Knob to adjust volume level as desire.
Press the /SCAN Button to pause; press again to resume normal playback
Press the or Buttons repeatedly to skip the tracks.
Press and holding the or Buttons to fast searching the specific section.
5. To stop CD playback, press the /BAND Button. The total number of tracks will appear on the
display.
6. When finished listening, slide the Function Selector to OFF position to power off the unit.
Programmed Playback:
Up to 20 tracks can be programmed playback as follows:
1. In CD STOP playback mode, press the M Button. "PROG 1 --"” will appear on the display and
blinking.
2. Select the first specific track to be programmed by pressing the or buttons repeatedly.
3. Press the M Button to store the selected track into the memory.
4. Repeat steps 2 and 3 until all the specific tracks stored into the memory.
5. Press the>ll/SCAN Button to start program playback. The program indicator "PROG" will stop
blinking.
6. To stop playback, press the /BAND Button.
7. To erase the program, press the /BAND Button again in stop mode. The program indicator will
disappear on the display.
Repeat/Random Playback:
1. During playback (or program playback), press the M Button once. The repeat one indicator “REP”
will appear on the LCD Display. The current track will playback repeatedly.
2. During playback, press the M Button twice. The repeat all indicator “REP ALL” will appear on the
LCD Display. All the tracks on the current disc (or program) will be playback repeatedly.
3. During playback, press the M Button three times, the random indicator "RAND" will appear on the
LCD Display. The unit will play the tracks randomly.
4. To cancel the repeat and random play functions, press the M Button repeatedly until all
repeat/random playback indicators disappear on the LCD Display or press the /BAND Button to
stop playback.
Note: Random playback is not available in program playback mode.

BT (BLUETOOTH):
BT pairing and play:
First time use or re-pairing the unit to a new BT Device, pair as follows:
1.Slide the Function Selector to BT/CD/AUX position to turn on the CD. The LCD Display will
illuminate and indicator “CD” will appear.
2.Press the BT/CD Button on the top of the unit to switch the unit from CD mode to BT mode:
The Indicator on the front of unit will illuminate and blink.
Indicate “bt” will appear on the LCD Display and blink.
3.Power on the external BT Device and enter to BT searching mode. Start pairing following the on
screen instructions from the external BT Device. After paired, the indicate “bt” on the LCD Display
and Indicator on the front of unit will stop blinking.
4.If pairing is complete you may now play music with your external BT Device.
5.During playback:
Turn the VOLUME Control Knob to adjust volume level as desire.
Press the /SCAN Button to pause; press again to resume normal playback.
Press the or Buttons repeatedly to skip the tracks.
6. When finished listening, slide the Function Selector to OFF position to power off the unit.
Notes:
1. When the external BT Device searched the unit, ou r model number “MD6927” will appear on the
display of external BT Device.
2. If while pairing you are asked for a code please try "0000" or "1234".
Normal operation after pairing:
1. Slide the Function Selector to BT/CD/AUX position to turn on the CD. The LCD Display will
illuminate and indicator “CD” will appear.
2. Press the BT/CD Button on the top of the unit to switch the unit from CD mode to BT mode:
The Indicator on the front of unit will illuminate and blink.
Indicate “bt” will appear on the LCD Display and blink.
3. Wait a few seconds until the unit is automatically paired to the external BT Device. The indicate
“bt” on the LCD Display and Indicator on the front of unit will stop blinking.
4. After pairing is complete you may now play music with your external BT Device.
10

11
AUX (in):
1. Insert one end of the Audio Connect Cable (not included) to the AUX Out; Line Out or Phones
Jack on the external Audio Player.
2. Insert the other end to the AUX (in) Jack on the left of unit.
3. Slide the Function Selector to BT/CD/AUX position to turn on the unit. The unit will
automatically switch to AUX (In) mode. The LCD Display will illuminate and indicator “AUX” will
appear.
4. Play the music on the connected external Audio Player as usual.
5. Turn the VOLUME Knob to adjust volume level as desired.
6. When finished listening, slide the Function Selector to OFF position to power off the unit.
NOTES:
Make sure the sound output level of the connected external Audio Device in high level.
Otherwise, sound will weak.
If sound is distorting, reduce the volume of the connected external Audio Player or set the EQ
mode of it to normal.
DECPRATIVE LED LIGHTS:
Press the Button on the top of unit repeatedly to set the blinking modes or turn it off as desired.
HEADPHONE JACK:
For private listening, connect the 3.5mm plug from the Earphone/Headphone (not included) into the
HEADPHONE Jack on the left of unit. Sound from speakers will be auto cut.

12
Check the following before requesting service:
SYMPTOM POSSIBLE CAUSE POSSIBLE SOLUTION
No power
AC Power cord had not connected Connect the AC Cord to the rear of
unit and any wall outlet having AC
120V~; 60Hz
No sound or sound weak
Volume of the unit was set to
minimum position
Increase the volume level by turning
the VOLUME Control Knob
clockwise
Volume level of paired/connected
device is in low level
Rise the volume level of the
paired/connected device
Soun
d
distortion
Volume level too high Reduce the volume level by turning
the VOLUME Control Knob
counterclockwise
Volume level of the connected/paired
device too high
Reduce the volume level of the
connected/paired device
CD or BT not functioning Audio Connection Cable was
inserted into the AUX (In) Jack
Unplug the cable from AUX (In) Jack
BT not functioning
The external BT Device had NOT
paired to the unit
Pair the external BT Device to the unit
as page 10
The external BT Device too far from
the unit
Place the external BT device close to
the unit
CD not play
Disc is dirty or scratched Try other discs
CD disc incorrect install Place the CD disc on the center spindle
with label side face up
CD compartment door is not closed. Close CD door completely.
Power Source: AC 120 V~; 60 Hz; 16 W, Or
DC 9 V; 8 x “C” size batteries (Not included)
BT Version: 2.1
BT Operation Distance: ≧32 Feet in opera area
Radio Frequency: AM: 535-1710 kHz
FM: 87.5-108 MHz
Disc Compatible: CD; CD-R; CD-RW
Impedance of Speakers: 2 x 1.5 W; 4+4 ohm
Audio power: 1.5 W per Channel (Total 3W, RMS)
1 x Owner’s Manual
1 x AC Power Cord
SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE WITHOUT NOTICE
TROUBLESHOOTING
GENERAL SPECIFICATIONS
ACCESSORIES