Majestic RUBY30IN User manual

1
Majestic • CKRUBY30, CKRUBY35 Contemporary Kit Instructions • 2542-939 Rev. B • 2/19
TOOLS
Screw gun equipped with 1/4 in. socket or
1/4 in. wrench
3/8 in. wrench
Instructions for optional glass kit, stone kit or log set if
applicable.
Leave this manual with party responsible for use
and operation.
CKRUBY30, CKRUBY35
Models: RUBY30IN, RUBY30IL, RUBY35IN, RUBY35IL
Installation Instructions
CAUTION! Do not install damaged components.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and shall be installed for
the protection of children and other at-risk
individuals.
Preparation
CAUTION! Risk of Burns! The replace should be
turned off and cooled before contemporary kit is installed.
• Shut off gas supply and disconnect electrical power.
• Remove decorative front, glass assembly, glass seal
plate, lava rock, embers, logs and refractory, if previ-
ously installed.
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during instal-
lation. Sheet metal edges are sharp.
WARNING! Choking Hazard! Keep media out of reach
of children.
Note: If an optional LINER kit will be used with the CK-
RUBY30/35, the LINER kit instructions will be needed
during installation of the CKRUBY30/35 kit.
Note: The CKRUBY30/35 is not compatible with ber
refractory.
WARNING! Risk of Injury! This kit must be installed by
a qualied service technician.
Models
(U.S. or Canada)
Maximum
Input
BTU/h
Minimum
Input
BTU/h
Orice
Size
(DMS)
Shutter
Setting
CKRUBY30
(NG) (0-2000 FT) 28,000 19,600 38 1/2 in.
CKRUBY30
(Propane) (0-2000 FT) 23,000 16,100 .058 in.
Full
Open
CKRUBY35
(NG) (0-2000 FT) 30,000 21,000 37 3/8 in.
CKRUBY35
(Propane) (0-2000 FT) 28,000 19,600 1.55 mm
Full
Open
BTU Specications

2Majestic • CKRUBY30, CKRUBY35 Contemporary Kit Instructions • 2542-939 Rev. B • 2/19
Installation Instructions
1. Remove base refractory.
2. Remove the screws that attach the base pan to the
burner and lift the base pan out of the appliance.
3. Remove the burner bracket screw. Slide burner to the left
and lift out of the appliance. Be careful not to damage the
pilot sense rod.
4. Remove the exhaust bafe and replace with contem-
porary exhaust bafe. See Figure 2.
5. Remove the orice using a 3/8 in. wrench and replace
with correct orice for gas type. See BTU specication
table on page 1.
6. Adjust the air shutter and install contemporary burner
assembly. See BTU specication table on page 1.
7. Install contemporary base pan assembly.
Note: Install insulation board behind false back for
CKRUBY35 kit.
8. Install false back. See Figure 2.
Figure 1. Contemporary Kit Metal Components
KIT COMPONENTS (Shown in Figure 1)
(1) Basepan Assembly
(1) Burner Assembly
(1) False Back
(1) Exhaust Bafe
(1) Bag Onyx Glass Media
(1) Bag Diamond Glass Media
(1) Bag 1/2 inch screws (25 screws per bag)
(1) Conversion Plate
(1) Stone Placement Jig
(1) Propane Orice - .058", 1.55 mm
(1) NG Orice - 38, 37
(2) Insulation Board (CKRUBY35 Only)
9. If installing the glass refractory kit, refer to the installa-
tion instructions that came with the kit and install now.
10. If installing logs, refer to the instructions with the kit
and install now.
11. Install glass media. When using multiple media col-
ors, mix them prior to installation. For optimal per-
formance and ame appearance, ensure it is spread
evenly. See Figure 3.
Figure 2. Screw Location
EXHAUST
BAFFLE
STONE
PLACEMENT
JIG FALSE BACK
ROCK STOP
JIG
PILOT
HOOD
BURNER
ASSEMBLY
BASE PAN
ASSEMBLY
EXHAUST BAFFLE
SCREWS
FALSE BACK SCREWS
ADDITIONAL COMPONENT - 35 in. ONLY
INSULATION
BOARD
Models Media
Quanity (Bag)
CKRUBY30 (NG) 1-1/4
CKRUBY30 (Propane) less than 1-1/4
CKRUBY35 (NG) 1-1/2
CKRUBY35 (Propane) less than 1-1/2
Media Chart
CAUTION: Place only one thin layer of media over the
burner and base pan when using Propane gas. Excess
media on burner and base pan may cause sooting. One
thin layer of media may require less media than indicated
in the above media chart.

3
Majestic • CKRUBY30, CKRUBY35 Contemporary Kit Instructions • 2542-939 Rev. B • 2/19
Figure 4. Stone Jig in Place
WARNING
Risk of Asphyxiation or Fumes.
• Place media according to instructions.
• Do NOT place media in area between glass and
rebox.
• Do NOT place media in a position that they may
fall into area between glass and rebox.
• Do NOT use any media other than the media
supplied with this replace.
Fireplace will not function properly.
Gas leak may occur.
WARNING
Delayed Ignition Risk
• Place media according to instructions.
• Do NOT place media in a position that they may
fall into area in front of pilot.
• Do NOT use any media other than the media
supplied with this replace.
• Do NOT exceed one layer of media on base pan.
Fireplace will not function properly.
Delayed ignition may occur.
12. If installing a stone kit, refer to the instructions in
the next section.
13 Remove rock stop.
Consumer: Retain rock stop for future maintenance
or service needs.
14. Reinstall seal plate, glass assembly and decorative
front.
15. Re-connect electrical supply and turn on gas.
Service Parts
MODEL DESCRIPTION PART NUMBER
CKRUBY30
Burner Assembly 2535-007
Exhaust Bafe 2535-138
Base Pan 2542-131
CKRUBY35
Burner Assembly 2536-007
Exhaust Bafe 2536-138
Base Pan 2544-131
Insulation Board 2536-158
BOTH
Rock Stop Assembly 2535-197
Stone Placement Jig 2542-198
Pilot Shield 2535-120
Note: A tall, deep orange ame should be avoided; this
type of ame may cause increased soot residue. If this
type of ame is noticed, try adjusting the media directly
beneath the ame. If all ames appear to be tall and deep
orange in color, then open the primary air shutter.
Please contact your Majestic dealer with any questions
or concerns.
For the location of your nearest Majestic dealer,
please visit www.majesticproducts.com.
Majestic, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.majesticproducts.com
Installing Stone Kit
NOTE: Rock Stop Jig must be in place to install
stones.
1. Place stone jig on glass media with “STONE JIG” fac-
ing up. Ensure that the stone jig sits ush against the
rock stop. See Figure 4.
2. Place stones in a random manner in the open spots on
the base pan.
3. Remove stone jig and then the rock stop.
Consumer: Retain both stone jig and rock stop for
future maintenance or service needs.
Figure 3. Glass Media Installed
WARNING! Glass seal plate must be properly installed
Risk of elevated component temps and carbon monox-
ide exposure.
ROCK STOP
REAR MEDIA LEDGE
ROCK STOP
STONE JIG
STONES