Makita 6410 User manual

Drill
10 mm 13/8"l 25 mm 11")
10 mm (3/8") MODEL 6410
Variable speed I Reversing
0 - 2,200 248 mm 19-3/4"1 1.2 kg (2.6 lbsl
INSTRUCTION MANUAL
f
DOUBLE
lal INSULATION
SPECIFICATIONS
I
Overall length Net weight
I
No load speed
IRPMI
Drillingcapacities
Steel
Wood

GENERAL SAFETY RULES
(For All Tools)
WARNING! Read and understand all instructions. Failure
tofollow all instructions listed below, may result
in electric
shock, fire and/or serious personal
injury.
SAVE THESE INSTRUCTIONS
READ ALL INSTRUCTIONS.
WORK AREA
1. Keepyour work area clean andwell lit. Clutteredbenchesanddark areas invite
accidents.
2. Do notoperatepowertools in explosive atmospheres, suchas in thepresence
.. of flammable liquids, gases, or dust. Power tools create sparks which may
ignite the dust
or fumes.
3. Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to loose control.
ELECTRICAL SAFETY
4. DoubleInsulatedtoolsareequipped with a polarizedplugloneblade iswider
than the other.) This plug will
fit in a polarized outlet only one way. If the
plugdoes not
fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install a polarized outlet. Do not change
the plug
in any way. Double insulation El eliminates the need for the three
wire grounded power cord and grounded power supply system.
5. Avoid bodycontact withgroundedsurfaces such as pipes, radiators, ranges
and refrigerators. There is an increased risk of electric shock if your body is
grounded.
6. Don't expose powertools torain or wet conditions. Water enteringa power
tool will increase the risk of electric shock.
7. Do notabuse the cord. Never use the cordtocarrythe tools or pull theplug
froman outlet. Keepcordaway from heat,
oil. sharp edges or movingparts.
Replace damaged cords immediately. Damaged cords increase the risk of
electric shock.
8. When operatinga powertooloutside, use anoutdoor extensioncordmarked
"W-A"
or "W." These cords are rated for outdoor use and reduce the risk
of electric shock.
PERSONALSAFETY
9. Stayalert, watchwhatyouaredoingand use commonsensewhenoperating
a power tool. Do not
use tool while tired or under the influence of drugs,
alcohol, or medication.
A moment of inattentionwhile operatingpower tools
may result
in serious personal injury.
IO. Dressproperly. Do notwear loose clothing or jewelry. Containlonghair. Keep
your hair, clothing, andglovesaway frommovingparts. Looseclothes, jewelry
or long hair can be caught
in moving parts.
2

..
11. Avoid accidentalstarting. Be sure switch isoff before plugging in. Carrying
tools withyour finger onthe switchor plugging
in tools that havethe switch
on invites accidents.
12. Removeadjusting keys or switches before turning the toolon. A wrenchor
a key that isleft attachedto a rotating part of the tool may result
in personal
injury.
13. Do notoverreach. Keepproper footing andbalanceatalltimes. Proper footing
and balance enables better control of
the tool in unexpected situations.
14. Use safety equipment. Always wear eye protection. Dust mask, non-skid
safety shoes, hard hat, or hearing protection must be used for appropriate
conditions.
TOOL USE AND CARE
15. Use clamps or other practical way to secure and support the workpieceto
a stable platform. Holding the work by handor against your body is unstable
and may lead to loss
of control.
16. Do notforce tool. Use the correct toolfor your application. The correct tool
will do the job better and safer at the rate for which
it is designed.
17. Do not use tool if switch does not turn it on or off. Any tool that cadnot
be controlled with the switch is dangerous and must be repaired.
18. Disconnecttheplugfromthepowersource before makingany adjustments,
changing accessories, or storing the tool. Such preventive safety measures
reduce the risk of starting
the tool accidentally.
19. Store idle tools out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
20. Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintainedtools, with sharp cuttingedges are less likely to
bind andare easier
to control.
21. Check for misalignment or binding of moving parts, breakage of parts, and
any other condition that may affect the tools operation. If damaged. have
the tool serviced before using. Many accidents are caused
by poorly main--
tained tools.
22. Use only accessories that are recommended by the manufacturer for your
model. Accessoriesthat may be suitable for one tool, may become hazardous
when used on another tool.
SERVICE
23. Tool service must be performedonly by qualified repair personnel. Service
or maintenance performed by unqualifiedpersonnel could result
in a risk of
injury.
24. When servicing a tool, use only identical replacement parts. Followinstruc-
tions
in the Maintenance section of this manual. Use of unauthorized parts
or failuretofollow MaintenanceInstructions maycreate arisk of electric shock
or injury.
3

Specific Safety Rules
1. Holdtoolby insulated grippingsurfaces when performinganoperationwhere
the cutting tools may contact hidden wiring or its own cord. Contact with
a "live" wire will make exposed metal parts
of the tool "live" and shock the
operator.
Be sure
no one is below when using the tool in high locations.
2. Always be sure you have a firm footing.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not leave the tool running. Operate the tool only when hand-held.
6. Do not touchthe drill bit or the workpieceimmediately after operation; they
may be extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
4
1 -_

..
..... ., . :$:
......
.. , _.
.. :.. ..
:. .....
. r:
...
.:>*!..:.'
ii :;..
.., ;; i ,:. ....
"?.
i iL,i!,?,:
-..vi, ![ {!
....
SYMBOLS
The followings show the symbols used for tool.
...
..
................................. volts
................................. amperes
................................. herts
................................. hours
................................. minutes
................................. seconds
................................. kilograms
f
alternating current
direct current
................................. noloadspeed
alternating or direct current
....................... Class I1 Construction
splash-proof construction
................... watertight construction
revolutions or reciprocation per minute
.......... number of blow
5

ASSEMBLY
Installing or removing drill bit
CAUTION:
Always be sure that the tool is switched off and unpluggedbeforeinstalling
or removing
the bit
Hold the ring and turn the sleeve counter-
clockwise to open the chuck jaws. Place
the bit inthe chuck as far as it will go. Hold
the ring firmly and turn the sleeve clock-
wise to tighten the chuck.
To remove the bit. hold the ring and turn
the sleeve counterclockwise.
OPERATION
Switch action
Tool speed isincreasedby increasingpres-
sure on the trigger.
To start the tool, simply
pullthe trigger. Release the triggerto stop.
For continuous operation,
pull the trigger
and then push in the lock button.
To stop
the
lool from the locked position, pull the
trigger fully, then releaseit.
6

.. Reverrlng switch action r
The reversing switch changes the direction
of rotation.
Movethe reversingswitchlever
to the “0’’
positionfor clockwiserotation.
Move the reversingswitch lever to the
“W
positionfor counterclockwiserotation.
Reversing
-switch lever
1
CAUTION:
*Beforeplugginginthe tool, alwayscheck
to see that the switch triggeractuatesproperly
andreturns
to the “OFF” positionwhen released.
*Always check thedirection
of rotationbeforedrilling.
*Use the reversingswitch lever only when the tool comes
to a complete stop. Changing
the directionof rotationbeforethe
tool stops may ruinthe tool.

Drilling operation
*Drilling inwood
When drilling holes in the wood, use a wood drill with
a guide screw. The guidescrew
makesit borenaturallyby itself,
so youdo not needto apply any pressuretothe tool.
To preventthe bit from slippingwhen startinga hole, make an,indentationwith acenter-
punch and hammer at the point to be drilled. Placethe pointof the bit inthe indentation
andstart drilling.
Use a cutting lubricant when drilling metals. The exceptions are iron and brass which
shouldbedrilled
dry.
*Drilling inmetal
CAUTION:
*Pressingexcessively onthe toolwill not speed upthe drilling. Infact, this excessivepres-
sure will only serve to damage the tip of your bit. decrease the tool performanceand
shortenthe servicelife of the tool.
*There is a tremendous force exerted on the toolbit at the time of hole break through.
Holdthe toolfirmly andexertcarewhen the bit beginsto breakthroughthe workpiece.
*Always grip the smallworkpiecefirmly with
a vise or a holdingmeans
*A stuck bit canbe removed simplyby setting the reversingswitch to reverse rotationin
order to backout. However, the tool will pullaway easily unlessyou holditfirmly before
startingthe tool.
R

MAINTENANCE
CAUTION:
Always be sure that the tool is switchedoff and unpluggedbeforeattempting to perform
inspection
or maintenance.
To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and
replacement, any other maintenance
or adjustment should be performed by Makita
Authorized
or FactoryServiceCenters, always using Makitareplacementparts.
9

j.
A&q.-30-'96 us
10 mm (318")
DRILL
Model 6410
Note: The switch and other part configurations
may differ from country
to country.
.n

-30-'sn us MOOEL 0410
A$D DESCRIPTION ';\M A$D DESCIIIPTION
.!

MAKITA LIMITEDONE YEAR WARRANTY
I
This Warranty gives you specific lepl riEhts, and you may also hive other rights which vary from
state to state. Some stilea do not allow the exclusion or limitation Of incidental or conrqucntial
dm8.5n
10 the above limitation or exclusion may not apply to you. Some 118tr.s do not allow
lhnitatiob on how lonb an implied warranty
luts. IO the above Umitatlon may not apply to you.
I
Warranty Policy
Every MakIta tool is thorou ly ins ectcd and tested before leavingthe factow. It is wanmted to
be free of defects from worfmanshr and m8terialr for Le period of ONE YEAR from the date of
nrl.insl ourchue. Should mv troubt develos durinithh one-vmr ~eriod. return the COMPLETE
i~l?&iii~ri&<~~ii~ini of Mikiii'rFictdry or Ailhodzed bnl& Cenlerr If Lnspatlon show
the irouble Is cause6 by defective worhinshlp 01 material. MakIti Vill repair (of at our Opthn.
replace)
without charge.
ThJs W.rranty docs not apply where:
0 rcpdn have been mde or attempted by othen:
mpdn arc required becaur of noImJ vcu md tear'
The tool hubeen abused. misused or Improperly maintained;
e ilterations hive been made to the Id.
IN No EVENT SIIALL MAKlTA BE LIABLE FOR ANY INDIRECT. INCiDENTAL OR CON-
SEQUENTIAL DAMAGES FROM THE SALE OR USE OFTHE PRODUCT.THIS DISCLAIMER
I APPLIES BOTH DURING AND AFTER THE TERM OF TlllSWARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES INCLUDING IMPLIED
WARRANTIES
OF "MERCHANTABILITY" AND "FITNESS FOR k SPECIFIC PURPOSE."
AFTER TllEONE-YEAR TERM OFTHISWARRANTY.
Makita(China) Co., Ltd.
HUANGPUJIANG ROAD,
KUNSHANECONOMIC
B
TECHNICALDEVELOPMENTZONE,
JIANGSU
RR. CHINA
884093 - 065
PRINTED INJAPAN