Mami HOG User manual

MAMI
MANUFACTURING AND MINOR INVENTIONS
LONG RANGE REMOTE CONTROL (HOG) D1
M000051

HOG (LONG RANGE REMOTE CONTROL)
Description:
The Hog (long range remote control) is a UHF 100mW transmitter capable of activating up to 4 relay outputs in a
receiver up to 6 km away (depending on terrain). The 4 inputs (channels) on the transmitter each correspond
to a relay on the receiver. Each relay on the receiver can be individually programmed to perform different functions
such as momentary, timer, toggle ( see receiver instructions). The device (ID) codes may vary from 1 - 1023.
IS
EXT
RX - +
1 2 3 4
Typical application:
4 channel Receiver
Ch1
Ch 2
Ch 3
Ch 4
ID CODE PROGRAMMING
The
done manually (see below ) or using our standard universal programmer (Supplied separately).
Manual programming:
This is accomplished by using the Inc and Step buttons. Please note that a five digit number is always required, no higher
than 1023.
Please follow these simple steps carefully:
1- Apply power to the unit
2- Press and hold the button until the green and red LED flash continuously
3- Using the and the buttons enter a 5 digit number
(NO HIGHER THAN 01023) which will be the Transmitter Code (ID).
4- After the fifth digit is entered the onboard LEDs will flash to indicate completion.
5- Press the button TWICE to exit programming or simply remove
power.
Hog’s basic functions are preprogrammed in the factory. The ID code MUST be programmed by the user. This can be
Transmitter code:
Inc
Inc Step
Step
LEDS
EXT
A
B
RX
1 2 3 4
POWER
+
-
Inc
Step
LEDS
EXT
A
B
RX
1 2 3 4
POWER
+
-
Inc
Step
PWR
Examples on next page
Parameter Min. Typ. Max. Unit
Power supply: Voltage D.C 10 13 13.8 V (dc)
Current (100 mW) 100 mA
Current (800 mW) 250 mA
Transmitted power (link out) rms (50 Ohms) 80 90 100 mW Transmission duty cycle = intermittent 50 %
Application current consumption Min. Typ. Max. Unit
Transmitter in permanent power mode 30 35 40 mA(13vdc)
Transmitter in Self-timed powered mode 0 0 0 mA(13vdc)
Transmitter in Input powered mode 0 0 0 mA (13vdc)
How to open the HOG:
Insert allan key into grub screw and turn anti clockwise to unscrew.
S S S IISI I S
I
00123
(Step) (Inc)
Steps you to the next digit and Increments that digit
1. To program the Transmitter (ID) Code to 00123 (5 digits with leading zero)
Hold the I button until the green and red LED flash continuously.
Now using and S enter 5 Digits (00123) =I
Examples:
S S IIS
I I S I
002
3
(Step) (Inc)
Steps you to the next digit and Increments that digit
2. To program the Transmitter (ID) Code to 01132 (5 digits with leading zero)
Hold the I button until the green and red LED flash continuously.
Now using and S enter 5 Digits (00132) =I
I
IS
1
Connections:
Yellow: Channel 1
Green: Channel 2
Blue: Channel 3
White: Channel 4
Red: Positive 12v
Black: Negative 12v
Side
Top
Technical Specifications
1A FUSE
1A FUSE
fig. 1
BATTERY or
EXTERNAL SUPPLY:
10/13.8V DC
300 mA(MINIMUM)
BATTERY or
EXTERNAL SUPPLY:
10/13.8V DC
300 mA(MINIMUM)
STAND BY CURRENT=
10 mA
fig. 2
RX - +
1 2 3 4
IS
EXT
Top view
A
A
RX - +
1 2 3 4
IS
EXT
TST
B
note: stand-by current = 0
Top view
For PERMANENT Power Supply
Jumper A = IN Jumper B= OUT
B
For INPUT SUPPLIED Power
Jumper A = IN Jumper B= IN
A
Permanent power
12v dc supply is permanently connected to the unit.
Contacts are connected to the 4 inputs
a small (20mA) current is constantly drawn
trigger (+12v dc) is applied to any of the inputs
(Normally Open contact may be used) no current
is drawn but transmission stops on removing the
trigger input.
Power applied through the inputs
The negative is permanently connected power and
NB: Make sure the HOG is closed and seated properly when replacing cover.
2 M000051 1 M000051