Manaras Opera KEYLESS 042 User manual

KEYLESS 042
KEYLESS 042
Programming and Installation Instructions
Programming and Installation Instructions
WARNING
TO REDUCE THE RISK OF SEVERE INJURY OR
DE TH TO PERSONS:
1. RE D ND FOLLOW LL INST LL TION INSTRUCTIONS.
2. Locate the Keypad: (a) within sight of the door, (b) at a minimum height of 5 feet
(1.5 m) above floors, landings, steps or any other adjacent walking surface so small
children are not able to reach it, and (c) away from all moving parts of the door.
3. ctivate the door ONLY when it can be seen clearly, is properly adjusted, and there
are no obstructions to the door travel.
Components:
Preparation:
1. Locate the LEARN button on the operator's On-Board Radio Receiver, refer to Figure 1 or the operator's
Installation & Instruction Manual.
2. Ensure that the Rotary Selection Switch on the operator's Electronic Control Board (ECB) is set to B2 (1),
T (4) or TS (5).
Figure 1 - Electronic Control Board (ECB)
3. Undo the screw from the bottom of the case and remove the back cover from the Keypad to install the
battery, refer to Figure 2.
4. Program the Key ad rior to mounting.
1-800-361-2260
www.manaras.com 1TN1025 REV 4 - 2016/04/11
1,5V AAA BATTERY
2 PCS M3,5 X 20 SCREWS
AND ANCHORS
KEYPAD (TRANSMITTER)
LEARN
BUTTON
LED (WHITE)
ROTARY
SELECTION
SWITCH
ON-BOARD
RADIO
RECEIVER
BOTTOM
SCREW
INSERT
BATTERY
Figure 2 - KEYLESS042 Battery Installation

KEYLESS 042
KEYLESS 042
Programming and Installation Instructions
Programming and Installation Instructions
New Installation:
Program an Initial PIN
1. Enter the factory default PIN [ 0 0 0 0 ] on the Keypad
Then press the [ * ] button
2. Enter a new PIN (2 to 8 digits) of your choice [ ? ? ? ? ]
Then press the [ * ] button
3. Re-enter the new PIN [ ? ? ? ? ] to confirm
Then press the [ * ] button
► The new PIN is confirmed once the Keypad's backlit LED flashes 3 times and the unit emits a long beep.
Anti-Theft Feature
The Keypad is designed with a security feature to prevent thieves from continuously guessing the PIN. If
there are 10 consecutive incorrect PIN attempts made by the user, the Key ad will auto-lock itself for a
eriod of 10 minutes. Removing the battery will not disengage the anti-theft feature. Wait for a period of 10
minutes before resuming to program the Keypad.
► The Keypad is ready to receive an input as soon as the unit emits a beep when a button is pressed.
Timeout Feature
In the event that more than 15 seconds has elapsed between any two keypad inputs during the programing
procedure, the unit will emit an error code of 5 short successive beeps.
► The programming procedure in progress must be restarted.
Keypad Pairing / Programming Instructions:
INGLE Door Mode Programming Instructions
llows for 1 door to be operated by the Keypad.
Single Door Setting Pairing Testing
1. Enter the PIN [ ? ? ? ? ]
Then press the following sequence
of buttons [ * ] [ 0 ] [ # ]
1. Press and HOLD the LEARN
button on the On-Board Radio
Receiver for approx. 2 sec. or until
the White LED on the Receiver
flashes.
1. Enter the PIN [ ? ? ? ? ]
Then press the [ # ] button to
operate the door
2. Enter the PIN [ ? ? ? ? ]
Then press the [ # ] button
► The Keypad will emit 3 beeps as
confirmation.
► The Keypad will emit 3 beeps as
confirmation.
► The Keypad will emit 3 beeps as
confirmation and the door operator
will activate.
1-800-361-2260
www.manaras.com 2TN1025 REV 4 - 2016/04/11
1
3
2

KEYLESS 042
KEYLESS 042
Programming and Installation Instructions
Programming and Installation Instructions
MULTIPLE Door Mode Programming Instructions
llows for a multiple doors (max. of 4) to be operated by the Keypad.
Multi le Door Setting Pairing Testing
1. Enter the PIN [ ? ? ? ? ],
Then press the following sequence
of buttons [ * ] [ 9 ] [ # ]
1. Press and HOLD the LEARN
button on the On-Board Radio
Receiver for approx. 2 sec. or until
the WHITE LED on the Receiver
flashes.
2. Enter the PIN [ ? ? ? ? ]
Then press the [ # ] button
Then the [ DOOR Number ] (1 to 4)
3. Repeat the procedure above for
the remaining doors.
To operate DOOR 1:
Enter the PIN [ ? ? ? ? ]
Then press the following sequence
of buttons [ # ] [ 1 ]
To operate DOOR 2:
Enter the PIN [ ? ? ? ? ]
Then press the following sequence
of buttons [ # ] [ 2 ]
To operate DOOR 3:
Enter the PIN [ ? ? ? ? ]
Then press the following sequence
of buttons [ # ] [ 3 ]
To operate DOOR 4:
Enter the PIN [ ? ? ? ? ]
Then press the following sequence
of buttons [ # ] [ 4 ]
► The Keypad will emit 3 beeps as
confirmation.
► fter each door is programmed,
the Keypad will emit 3 beeps as
confirmation.
► The Keypad will emit 3 beeps as
confirmation and the appropriate
door operator will activate.
Mounting Instructions:
1. Select a desired location to mount the Keypad at a minimum height of 5 feet (1.5 m).
2. Secure the back cover at the desired location with the two anchors and screws provided, refer to Figure 3.
3. Re-install the keypad unit to the back cover.
4. Gently tighten the screw at the bottom of the case.
1-800-361-2260
www.manaras.com 3TN1025 REV 4 - 2016/04/11
1
2
3
Figure - Mounting KEYLESS042

KEYLESS 042
KEYLESS 042
Programming and Installation Instructions
Programming and Installation Instructions
Troubleshooting:
Change an Existing PIN
1. Enter the programmed PIN [ ? ? ? ? ] that you want to change on the Keypad
Then press the [ * ] button
2. Enter a new PIN (2 to 8 digits) of your choice [ ? ? ? ? ]
Then press the [ * ] button
3. Re-enter the new PIN [ ? ? ? ? ] to confirm
Then press the [ * ] button
► The new PIN is confirmed once the Keypad's backlit LED
flashes 3 times and the unit emits a long beep.
Reset Keypad to Factory Default ettings
(when PIN is unknown or forgotten)
1. Remove the battery from the Keypad, refer to Figure 2,
p.4 .
2. Press and HOLD the [ # ] and [ * ] buttons simultaneously,
while inserting the battery in the Keypad, refer to
Figure 4 and Figure 5.
► The Keypad will emit a long beep.
3. Release the [ # ] and [ * ] buttons.
► The beep will stop after several seconds.
► The PIN has been reset to the factory default PIN [ 0 0 0 0 ]
and pairing between the On-Board Radio Receiver and the
Keypad is lost.
4. Refer to the instruction on how to Program an Initial PIN on
p.2 and the Keypad Pairing / Programming Instructions on p.2.
DELETE On-Board Radio Receiver Memory
1. Press and HOLD the Receiver's LEARN button on the On-Board Radio Receiver for approx. 10 sec. or
until the WHITE LED on the Receiver flashes quickly.
► This will clear the pairing of all transmitters (radio remotes and keypads) with the On-Board Radio
Receiver.
For further information, please consult the operator's Installation & Instruction Manual or contact our Technical
Support Department at 1-800-361-2260.
1-800-361-2260
www.manaras.com 4TN1025 REV 4 - 2016/04/11
Figure 4 - Reset Keypad
to Default Settings
Figure 5 - Insert Battery