Ace PK-210 User manual

PK-210
Proximity Keypad
User Manual & Operating Guide
www.accesscontrolequipment.co.uk
1 2 3
4 5 6
7 8 9
0 #
*

www.accesscontrolequipment.co.uk
ace
Main technical parameters:
ŸWorking voltage:
DC12-24V
ŸOpen key current:
<1000mA
ŸQuiescent current:
<60mA
ŸMemory capacity:
250 users
ŸInduction distance:
3~8 cm
ŸCard types:
EM
ŸWorking temperatures:
-10°C ~ 60°C
ŸWorking Humidity:
10% ~ 90%
ŸDimensions:
128 x 82 x 28mm
Front View
12 3
45 6
78 9
*0 #
LED lights
Keys
Rear View
Screws
K2
SW1
RESET
Speaker
Wiring block
Tamper switch
Reset Button
120000401 12,9458 000
Example of proximity card
Example of security screwdriver
TECHNICAL DATA AND DIMENSIONS

www.accesscontrolequipment.co.uk
Common power supply connection
Common 12v3A
NC
COM
NO
GND
12V
VSS
OPEN
PK - 210
GND
+12V
+V
- V
+V
- V
Power off = lock open
Power on = lock open
Common power supply connection
Special Power Supply
NC
COM
NO
GND
12V
VSS
OPEN
PK - 210
+V
- V
Power on = lock open
+V
- V
Power off = lock open
Open door button
Open door button
Wiring Diagram

www.accesscontrolequipment.co.uk
GB
2003/108/CE Directive
for waste electrical and
electronic Equipments
DISPOSE OF PROPERLY
ENVIRONMENT - NOXIOUS MATERIALS
EUROPEAN MARK CERTIFYING CONFORMITY
TO THE ESSENTIAL REQUIREMENTS OF THE
STANDARDS 98/37/EC
Made using
recycled
paper
The manufacturer reserves the right to make amendments to this manual without prior
notice and declines all responsibility for any errors, personal injury or damage to
property.
L.E.D
Light codes and their meaning:
ŸDefault ready state = Red Notes
ŸProgramming mode = Yellow/Red ŸProgramming mode will exit automatically after 12 seconds without
ŸAccepted program command = Yellow/Green input
ŸAwaiting info prog mode = Yellow ŸIf you need to cancel something mid-programming don't panic just
ŸAccepted user code = Green press the “#” key and this will exit programming mode
To enter programming mode:
ŸPress the “#” key
ŸEnter “12345" or (code you have programmed using “step 6")
ŸYou can now enter into one of the below steps of programming
To enter a new 6 digit code (to let users open barrier):
ŸEnter prog mode (follow step1)
ŸYellow/Red LED illuminated
ŸNow press the number “2" key
ŸYellow LED only illuminated
ŸEnter 4 digit User Slot Number i.e. “0001" (this can go up to “2000")
ŸYellow/Green LED illuminated
ŸEnter a 6 digit code e.g. “112233" OR present a card to the centre of
the keypad
ŸYou will hear a beep this confirms correct registration
ŸLED will return to Yellow/Red
ŸNow exit the program by pressing the “#” or “6" key
Ÿ
To remove the codes/cards:
ŸEnter prog mode (follow step1)
ŸYellow/Red LED illuminated
ŸNow press the number “4" key
ŸYellow LED only illuminated
ŸYou will hear a beep after 3 seconds
ŸLED will return to Yellow/Red
ŸNow exit the program by pressing the “#” or “6" key
Ÿ
To change “pulse” open signal time
ŸEnter prog mode (follow step1)
ŸYellow/Red LED illuminated
ŸNow press the number “5" key
ŸYellow LED only illuminated
ŸEnter pulse time minimum “01" 1 second or max “99" 99 seconds
most products only require 1 second
ŸFor 1 second enter “0" then “1" keys
ŸYellow/Green LED illuminated
ŸYou will hear a beep
ŸLED will return to Yellow/Red
ŸNow exit the program by pressing the “#” or “6" key
To change system password:
ŸEnter prog mode (follow step1)
ŸYellow/Red LED illuminated
ŸNow press the number “1" key
ŸYellow LED only illuminated
ŸEnter new 5 digit code e.g. “98765"
ŸYellow/Green LED illuminated
ŸYou will hear a beep
ŸLED will return to Yellow/Red
ŸNow exit the program by pressing the “#” or “6" key
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
To remove individual codes/cards:
ŸEnter prog mode (follow step1)
ŸYellow/Red LED illuminated
ŸNow press the number “3" key
ŸYellow LED only illuminated
ŸEnter the User ID to delete or present card
ŸLED will Flash GREEN (this is confirmation card/code has been
erased)
ŸLED will return to Yellow/Red
ŸNow exit the program by pressing the “#” or “6" key
ALL!!
Programming Instructions