ManoMano 03POH1010-V2 User manual

03POH1010-V2
Overall Dimensions:
Length = 308cm
Width = 314cm
Height = 211cm
Base Dimensions:
Length = 306cm
Width = 306cm
For Assistance Please
Contact Customer Care on
01636 880514
2mm Drill bit
x2
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
This building should be erected by
two people.
For ease of assembly, you must pilot
drill all screw holes and ensure all
screw heads are countersunk.
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand
(not supplied) including a Phillips screwdriver, Stanley knife, wood saw,
step ladder and drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be aected during various weather
conditions. For the duration of heavy or extended periods of rain, swelling of the
wood panels may occur. Warping of the wood may also occur during excessive
dry spells due to an interior moisture loss. Unfortunately, these processes cannot
be avoided but can be helped. It is suggested that the outdoor building is
sprayed with water during extended periods of warm sunshine and sheltered as
much as possible during rain or snow.
Our buildings are delivered pre-treated with a water based timber treatment
however this only helps to protect during transit of your garden item. To
validate your guarantee and for better protection against weathering it is
ESSENTIAL that you treat the garden building with a wood preserver within 3
months of assembly. This will need to be re-applied annually to ensure longevity
of your building. Care must be taken when constructing the garden building
that it is not touching the ground and is on a suitable base.
BUILDING A BASE
When thinking about where the building and base is going to be constructed: Ensure that there will be access to all sides for maintenance
work and annual treatment.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base dimensions, The base should be
slightly smaller than the external measurement of the building, i.e. The cladding should overlap the base, creating a run o for water. It is also
recommended that the oor be at least 25mm above the surrounding ground level to avoid ooding.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens products independently tested to EN71
level,we cannot accept responsibility for your safety whilst erecting or using this product.
Please retain product label and instructions for future reference
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Window Panel 1 Window Panel 2 Door Panel 1 Door Panel 2
Back Panel 1
Plain Door x3 Master Door
Back Panel 2
Roof x2 Floor x2
2
134
56
78
50mm Screw x80
40mm Screw x35
Felt Tacks x130
30mm Screw x117
50mm Bolt x2
70mm Screw x2
10mm Screw x40
100mm Screw x8
35 36

Fixing Kit
58x44x2932mm Truss Frame
58x44x1989mm Panel Frame
44x44x1989mm Front Panel Frame
58x44x170mm Truss support block
27x70x1468mm Truss sides
44x44x1943mm Rear Panel Frame
12x57x2009mm Cover Trim
12x45x2009mm Cover Trim
12x40x2009mm Cover Trim
12x45x1982mm Cover Trim
44x60x240mm Roof block
27x32x1963mm
12x95x1570mm Fascia
12x95x1500mm Fascia
12x40x1963mm Cover Trim
12x45x1963mm Cover Trim
x1
x1
x1
x2
x4
x1
x1
x2
x1
x2
x1
x1 Rear cover trim
x4
x2
x1
x1
Pair of door
handles
Chrome handle
Barrel bolt
Felt
58x44x1943mm Panel Frame x1
20
21
22
23
24
25
26
27
28 29
9
10
11
12
13
14
15
16
17
18
19
27x45x1558mm Roof Eave x2
16x60x1720mm Door Strip x2
30
31 32 33
Mortice Lock
Key Plate
37
Butt Hinge x12
a
a
a
a
a
a
a
a
a
a
a
a
4
3
a
35 35
36 35
37 30mm
screw
Pre Assembly
Fix the butt hinges to the doors and both door gables using
30mm screws ensuring that the screws go through to the
framing.
Make sure that the master door is positioned on the correct
side of the gable as shown below.
72x 30mm screws
Remove transportation blocks
from the bottom of each panel
before beginning assembly.
Each Panel should have two
blocks.
Step 1

Place floors on a firm and level base, ensure base has suitable
drainage free from areas where standing water can collect. (See
front page on base requirements).
Place floors flush against each other and fix together using 4 x
50mm screws , alternate fixing positions along the length of the
floors.
Step 3
50mm
screw
10 x 50mm screws
8
Fit the mortice lock into the recess and fix in place with the screws
provided. Fit the key plate using the screws provided.
Fix door handles using 8x30mm screws.
Then fit barrel bolts to top and bottom of the doors as shown in
diagram. Use 4x10mm screws per barrel bolt.
Ensure doors open and close freely.
Step 2
30mm
screw
10mm
screw
10mm
screw
31
31
28
3
4
32
33 The Mortice Lock is Reversible Step 4
Place Back Panel 2
on top of oor as
shown.
Pre-drill 3 holes
from Back Panel 2
and into Rear
Panel Framing
and attach
together using 3 x
50mm screws.
50mm
screw
3 x 50mm screws
6
14
Step 5
Place Back Panel 1
up against Rear
Panel Framing, pre
drill 3 holes and x
together using 3 x
50mm screws.
Fix the other 2
Panel Frames to
the ends using the
same method
ensuring to pre drill
holes rst.
50mm
screw
9 x 50mm screws
5
25
10

BUILDING A BASE
When thinking about where the building and base is going to be constructed: Ensure that there will be access to all sides for maintenance
work and annual treatment.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base dimensions, The base should be
slightly smaller than the external measurement of the building, i.e. The cladding should overlap the base, creating a run o for water. It is also
recommended that the oor be at least 25mm above the surrounding ground level to avoid ooding.
Step 6
The Door and Window panels can be placed in a variety of congurations (examples shown below),
place the panels into position according to preferred conguration. All panels are xed with the same
method using 50mm screws in the marked positions. Pre - Drill holes rst.
a
a
a
a
a
a
a
50mm
screw
6 x 50mm screws
2
1
!BEFORE FIXING DOOR PANEL!
Remove all transport screws from
top and bottom of door. Ensure
door opens and closes freely.
Step 7
Place the remaining panels
into position and x to the
other panels using 50mm
screws as shown in xing
method b, pre - drill holes rst.
Slot the remaining panel frame
against both panels on the
corner and x using xing
method a. Pre - drill holes rst.
a
aa
a
a a
b
b
b b
b
b
b
50mm
screw
12 x 50mm screws
3
9
4
Step 8
We strongly recommend pre drilling
holes before xing screws.
100mm
screw
100mm
screw
40mm
screw
Layout all the labelled parts used here to create the Truss. Pre - drill
a hole at either end of the Truss framing and x the Truss Block to
the bottom using a100mm screw from the top.
Place the Truss Supports on either side and x into
position using 40mm screws. Remember to pre -
drill holes rst
2 x 100mm screws
8 x 40mm screws
13
11
13
12

Step 9
Pre-drill Holes and x truss into position
using 2x 100mm screws per side.
4 x 100mm screws
We strongly recommend pre drilling
holes before xing screws.
c
c
c
c
c
c
c
c
c
c
c
c
c
50mm
screw
50mm
screw
50mm
screw
50mm
screw
70mm
screw
Step 10
Attach roof block to corner of one the roof panels as show below, pre drill
holes from the outside and x using 2 x 50mm screws.
Place roof panels on top making sure the roof block ts over the corner of
the building as shown below. Fix the roof block to the corner using 1
x70mm screw, ensure to pre-drill hole rst.
Fix roof panels to building using 50mm screws
1 x 70mm screws
20 x 50mm screws
We strongly recommend pre drilling
holes before xing screws.
7
7
19
100mm
screw

26
We strongly recommend pre drilling
holes before xing screws.
Cut felt into four sheets ensuring
they are long enough to cover roof
with 50mm overhang around the
sides. Overlap where the sheets
meet and x onto roof using felt
tacks at 10cm intervals.
Step 12
29
Fix all panels to oor using 50mm screws
in the position shown, again we recom-
mend pre drilling holes before hand to
reduce the risk of splitting the wood.
Make sure to align the screws with the
oor joists.
50mm
screw
50mm
screw
17 x 50mm screws
Step 13
40mm
screw
Step 11
Fix Roof Eaves to the back of the roof panels as shown. Using 3 x 40mm
screws per piece. Ensure to pre-drill holes rst to avoid splitting wood.
6 x 40mm screws
We strongly recommend pre drilling
holes before xing screws.

16
17
We strongly recommend pre drilling
holes before xing screws.
We strongly recommend pre drilling
holes before xing screws.
Fix Corner trims into position
using 3 x30mm screws. Pre-drill
holes rst.
24 x 30mm screws
30mm
screw
23
24
18
18
15
16
Step 14
Fix rear cover trim to back
corner using 3 x 30mm screws.
Pre-drill holes rst.
30mm
screw
3 x 30mm screws
20
Step 15
Fit the fascias to the building over
the felt and secure in place with
40mm screws as shown.
Pre drill to avoid splitting.
18 x 40mm screws
40mm
screw 21
21
22
22
21
21
Step 16
Pre drill holes then fix Chrome Handle using 45mm bolt as shown in diagram.
We strongly recommend pre drilling
holes before xing screws.
30
Step 17
2 x 45mm bolt

I
t
i
s
E
S
S
E
N
T
I
A
L
t
h
a
t
y
o
u
a
p
p
l
y
w
o
o
d
t
r
e
a
t
m
e
n
t
i
m
m
e
d
i
a
t
e
l
y
a
f
t
e
r
t
h
e
b
u
i
l
d
i
n
g
h
a
s
b
e
e
n
a
s
s
e
m
b
l
e
d
.
8 x 30mm screws
AFTER TREATMENT:
score around protective
cover on glazing and
carefully peel
covering back
Attach to this door
Attach to this door
30mm
screw
30mm
screw
Fix Door strips to outside, make sure to fit them to
the door without a handle on either side. Ensure
there is enough cover over the other door. Fix using
4x30mm screws per strip making sure to pre drill
Step 18
27 27