Mark U12-4440 User manual

Installation Advice
As the detector responds to changes in temperature, avoid the
following situations:
n
Avoid pointing the detector towards objects with highly
reflective surfaces, such as mirrors etc.
n
Avoid mounting the detector near heat sources, such as heating
vents, air conditioning units, light etc.
n
Avoid pointing the detector towards objects that may move in
the wind, such as curtains, tall plants etc.
n
Unload the transparent vinyl cover which is at the bottom of the
sensor.
n
Loose the screws in the connection terminal, and then connect
the power to connection terminal of sensor according to
connection-wire diagram.
n
Install back the transparent vinyl cover into the original
location.
n
Fold the metal spring of the sensor upwards, until they are in
“I” position with sensor, and then put the sensor into the hole or
installation box which is on the ceiling and has the similar size
with the sensor. Releasing the spring, the sensor will be set in
this installation position.
n
After finishing installing, turn on the power and then test it.
Connection
Warning. Danger of death through electric shock!
n
Must be installed by professional electrician.
n
Disconnect power source.
n
Cover or shied any adjacent live components.
n
Ensure device cannot be switched on.
n
Check power supply is disconnected.
Specification - Part Code U12-4440
Power Source: 220-240V/AC Detection Range: 360°
Power Frequency: 50/60Hz Detection Distance: 8m max(<24℃)
Time Delay: Min.10sec±3sec Ambient Light: <3-2000LUX (adjustable)
Max.15min±2min Working Temperature: -20~+40℃
Rated Load: Max.1200W Working Humidity: <93%RH
600W Power Consumption: approx 0.5W
Installation Height: 2.2-4m Detection Moving Speed: 0.6-1.5m/s
Infrared motion sensor - installation and operation manual
Kit Contents
IP65 360° PIR sensor single channel
The product adopts good sensitivity detector and integrated circuit. It gathers automatism, convenience, safety, saving-energy and
practical functions. It utilises the infrared energy from human as control-signal source and it can start the load at once when one enters
detection field. It can identify day and night automatically. It is easy to install and used widely.
Function:
n
Can identify day and night: The consumer can adjust working state in different ambient light. It can work in the daytime and at
night when it is adjusted on the “sun” position (max). It can work in the ambient light less than 3LUX when it is adjusted on the “3”
position (min). As for the adjustment pattern, please refer to the testing pattern.
n
Time-Delay is added continually: When it receives the second induction signals within the first induction, it will restart to time from
the moment.
[e-mail]
www.tlwglobal.com
[phone]
Mark Lighting

Installation
1 2 3 4
Problem Solving
Sensor Information Test
No activation
n Please check the connections to the PIR sensor
n Please check the power and load connection is live
n Please check the light fitting is in good working order
Sensitivity is poor
n Make sure nothing is blocking the PIR sensor’s detection view
n
Please check that the ambient temperature is within acceptable
operation range
n
Please check that the signal/activation source is within the
detection range of the PIR sensor
n
Please check the installation height does not exceed the
permitted range
The PIR sensor does not turn off as expected
n Please check the TIMER is set to the correct desired delay
n Please check the LUX setting is set to the correct desired level
n
Please check that an activation source is not present in the
room, causing the PIR sensor to remain active
n
Turn the TIME knob anti-clockwise on the minimum (10s).Turn the LUX knob clockwise on the maximum (sun).
n
Switch on the power; the sensor and its connected lamp will have no signal at the beginning. After Warm-up 30sec, the sensor can
start work .If the sensor receives the induction signal, the lamp will turn on. While there is no another induction signal any more, the
load should stop working within 10sec±3sec and the lamp would turn off.
n
Turn LUX knob anti-clockwise on the minimum (3). If the ambient light is more than 3LUX, the sensor would not work and the lamp stop
working too. If the ambient light is less than 3LUX (darkness), the sensor would work. Under no induction signal condition, the sensor
should stop working within 10sec±3sec.
Note: when testing in daylight, please turn LUX knob to (SUN) position, otherwise the
Height of installation: 2.2-4m
Detection Distance: Max.8m
[e-mail]
www.tlwglobal.com
[phone]
Mark Lighting