Marq Gesture Spot 300 User manual

Quickstart Guide English

2
Introduction
Box Contents
Gesture Spot 300 Quickstart Guide
Power Cable Safety & Warranty Manual
DMX Cable
Important: Visit marqlighting.com to download the complete User Guide.
Support
For the latest information about this product (documentation, technical specifications, system
requirements, compatibility information, etc.) and product registration, visit marqlighting.com.
For additional product support, visit marqlighting.com/support.
Safety Notes
Important: In addition to the notes below, please refer to the included safety & warranty manual for
additional safety information.
•Carry this product by the hanging/mounting bracket or the handles only.
•Use this product indoors only (IP20). To prevent risk of fire or shock, do not expose this product
to rain or moisture.
•Do not use this product for permanent installations.
•Connect this product to grounded and protected circuits only.
•Always disconnect it from its power source before cleaning or replacing this product’s fuse.
Replace the fuse with another of the same type and rating.
•Before connecting the product to a power source, make sure the power cable is not crimped or
damaged.
•Make sure the power outlet’s voltage is within the range stated on this product (on its housing or
decal).
•Never connect this product to a dimmer or rheostat.
•Never disconnect this product from the power cable by pulling or tugging on the cable itself.
•If you mount this product overhead, use a safety cable.
•Always make sure this product is used in a location with adequate ventilation with at least 20”
(50cm) from adjacent surfaces. Make sure none of this product’s ventilation slots are obstructed.
•Do not use this product at ambient temperatures higher than 104 °F / 40 °C.
•Do not allow flammable materials near this product during use.
•Do not look at the light source when the product is on.
•Do not touch this product while it is powered on or immediately after powering it off. The product
and its housing can reach high temperatures.
•If you encounter a serious problem while using this product, stop using it immediately.
•Do not open this product’s housing. It contains no user-serviceable parts and will void your warranty.

3
Features
Rear Panel
1. Power In: Use a standard power
cable (included) to connect this
input to a power outlet.
2. Fuse: This compartment holds the
fuse. Before cleaning or replacing
the fuse, disconnect Gesture
Spot 300 from its power source.
Use a screwdriver or other tool to
remove the compartment (do not
pull it out by the tab only). Replace
the fuse only with a new fuse with
the same rating (250 V, 4 A).
3. DMX In: Use a standard 3-pin DMX cable to connect this input (A) to your DMX controller or (B)
to another fixture that will pass DMX data through it to this one. Gesture Spot 300 receives DMX
data over this connection. Please see Setup > Linking > DMX for information about linking
multiple fixtures.
4. DMX Out: Use a standard 3-pin DMX cable to connect this output to an additional fixture.
Gesture Spot 300 sends its data to an additional fixture over this connection. Please see Setup >
Linking > DMX for information about linking multiple fixtures.
Front Panel
5. Display: This display shows
messages and values indicating
the fixture’s current status.
6. Menu: Press this button to access
Gesture Spot 300’s menu.
7. Up: Press this button to select the
next-highest menu option or to
increase the value by 1.
8. Down: Press this button to select
the next-lowest menu option or to
decrease the value by 1.
9. Enter: Press this to confirm your current selection or value.
10. DMX: This light will illuminate when Gesture Spot 300 is receiving DMX data properly through its
DMX In.
11. Error: This light will illuminate when Gesture Spot 300 receives an invalid DMX command.
5
6789
10
11
1
234

4
Setup
Note: Items not listed under the Introduction > Box Contents are sold separately.
Power Information
Before connecting the fixture to a power outlet, make sure the power cable is not crimped or
damaged. Also, make sure the power outlet’s voltage is within the range stated on this product (on
its housing or decal).
Before cleaning or replacing the fuse, disconnect Gesture Spot 300 from its power source. Use a
screwdriver or other tool to remove the compartment (do not pull it out by the tab only). Replace the
fuse only with a new fuse with the same rating (250 V, 4 A).
Mounting/Rigging
Standing
Place the fixture on a flat, stable surface. Make sure all cables are secured and placed so that no one
will trip over them.
Suspended
1
345
2
Clamp (not included)
Hanging Bracket
1/4-turn
1/4-turn
Follow these steps to use the
hanging bracket (included) for
mounting the fixture to a truss.
(tighten until
secure)

5
Linking
When using multiple Gesture Spot 300 fixtures, you can link (“daisy-chain”) them so that each each
fixture sends DMX data to the next one. This helps reduce clutter in your cabling and save you setup
time.
DMX
Use a standard 3-pin DMX cable to connect the DMX Out of one fixture to the DMX In of another.
Your connected DMX controller will send its data to the fixtures in sequence. All fixtures in this chain
will receive all DMX data.
According to the DMX standard, you can link up to 32 fixtures with up to 300 feet (91 meters)
between each fixture, without amplification. Keep in mind the number of channels you are using as
well as the starting address.
Gesture Spot 300 Gesture Spot 300 Gesture Spot 300
DMX Controller

6
Operation
Menu Options
Menu Submenu Settings/Values Description
DMX
Function
DMX Address 001
–
512 DMX address setting
Channel Mode 13Ch 13-channel operation
7Ch 8-channel operation
No DMX Signal Keep When no DMX signal, do nothing (hold)
Auto When no DMX signal, enter Run Mode
Clear When no DMX signal, black out
DMX Monito
r
V
iew values received on DMX channels
Auto
Movement
Run Mode See Description DMX, Sound, Random, 8 auto movement programs
Sound Active On, Of
f
Sound activation
Sound Sense 000
–
100 Sound-activation microphone sensitivity, low (000)
to high (255)
Slave Mode Slav 1
–
4 4 slave modes
Manual
Test
Pan 000
–
255 Pan angle, 0° (000) to 540° (255)
Pan Fine 000
–
255 Fine control of panning
Tilt 000
–
255 Tilt angle, 0° (000) to 270° (255)
Tilt Fine 000
–
255 Fine control of tilting
Pan/Tilt Time 000
–
255 Pan/tilt speed, fast (000) to slow (255)
Dimme
r
000
–
255 Dimmer, dark (000) to bright (255)
Stop/Strobe 000
–
255 Shutter (see 13-Channel Operation > Channel 7
)
Colo
r
000
–
255 Color options (see 13-Channel Operation > Channel 8
)
Gobo Change 000
–
255 Gobo options (see 13-Channel Operation > Channel 9
)
Gobo Rotation 000
–
255 Rotation, slow (000) to fast (255)
Prism Insertion 000
–
255 3-facet prism
Macro Function 000
–
255 Macro functions (see 13-Channel Operation >
Channel 12)
Ctrl Functions 000
–
255 Blackout & reset functions (see 13-Channel Operation
> Channel 13)
Fixture
Settings
Pan Limit 540
˚
, 360
˚
, 180
˚
Select range of pan angle: 540°, 360°, or 180°
Tilt Limit 270
˚
, 180
˚
, 90
˚
Select range of tilt angle: 270°, 180°, or 90°
Invert Pan On, Of
f
Invert pan direction
Invert Tilt On, Of
f
Invert tilt direction
Swap Pan-Tilt On, Of
f
Switch pan and tilt
Pan-Tilt Correction On, Of
f
Correct pan and tilt
Load Default All OK, Cancel Restore default pan and tilt settings

7
Menu Options (continued)
Display
Settings
Inverse Invert control panel’s display
Auto-Of
f
On, Of
f
Automatically turn off display when not in use
Fixture
Information
Firmware Currently installed firmware version
Total Use Hours Total running time (HHHHH:MM)
Current Use Hours Current use running time (HHHHH:MM)
Offset
Calibration
Pan Calibration -128
–
+127 Offset for pan value
Tilt Calibration -128
–
+127 Offset for tilt value
Color Calibration -128
–
+127 Offset for color value
Gobo Calibration -128
–
+127 Offset for gobo value
Gobo Rot. Calibration -128
–
+127 Offset for gobo rotation value
Prism Insertion -128
–
+127 Offset for prism value
Reset All OK, Cancel Restore all default settings
DMX Functions
You can control Gesture Spot 300 by linking it to a DMX controller. Please see the complete User
Guide at marqlighting.com to learn how to do this. See below for charts of available functions.
13-Channel Operation
Channel Function Value Description
1 Pan 000
–
255 Pan angle, 0° (000) to 540° (255)
2 Pan Fine 000
–
255 Fine control of panning
3 Tilt 000
–
255 Tilt angle, 0° (000) to 270° (255)
4 Tilt Fine 000
–
255 Fine control of tilting
5 Pan/Tilt Speed 000
–
255 Pan/tilt speed, fast (000) to slow (255)
6 Dimme
r
000
–
255 Dimmer, dark (000) to bright (255)
7 Shutte
r
000
–
003 Closed
004
–
007 Open
008
–
076 Strobe, slow (008) to fast (076)
077
–
145 Pulse, slow (077) to fast (145)
146
–
215 Random strobe, slow (146) to fast (215)
216
–
255 Open

8
13-Channel Operation (continued)
Channel Function Value Description
8 Color Wheel 000
–
006 White
007
–
013 Red
014
–
020 Green
021
–
027 Blue
028
–
034 Yellow
035
–
041 Purple
042
–
048 Light Blue
049
–
055 Orange
056
–
063 Pin
k
064
–
127 Color indexing
128
–
189 Clockwise, fast (128) to slow (189)
190
–
193 Stop
194
–
255 Counterclockwise, slow (194) to fast (255)
9 Gobo Wheel
See Technical Specifications >
Gobos to view gobo patterns.
000
–
007 Open/white
008
–
015 Gobo 1
016
–
023 Gobo 2
024
–
031 Gobo 3
032
–
039 Gobo 4
040
–
047 Gobo 5
048
–
055 Gobo 6
056
–
063 Gobo 7
064
–
071 Open spot shaking, slow (064) to fast (071)
072
–
079 Gobo 1 shaking, slow (072) to fast (079)
080
–
087 Gobo 2 shaking, slow (080) to fast (087)
088
–
095 Gobo 3 shaking, slow (088) to fast (095)
096
–
103 Gobo 4 shaking, slow (096) to fast (103)
104
–
111 Gobo 5 shaking, slow (104) to fast (111)
112
–
119 Gobo 6 shaking, slow (112) to fast (119)
120
–
127 Gobo 7 shaking, slow (120) to fast (127)
128
–
189 Counterclockwise gobo change, fast (128) to slow (189)
190
–
193 Stop at current position
194
–
255 Clockwise gobo change, slow (194) to fast (255)
10 Gobo Rotation 000
–
127 Indexed position, 0° (000) to 360° (127)
128
–
189 Counterclockwise gobo scroll, fast (128) to slow (189)
190
–
193 Stop at current position
194
–
255 Clockwise gobo scroll, slow (194) to fast (255)
11 Prism 000
–
127 No function
128
–
255 Prism effect

9
13-Channel Operation (continued)
Channel Function Value Description
12 Macro Functions 000
–
007 No function
008
–
023 Automatic movement 1
024
–
039 Automatic movement 2
040
–
055 Automatic movement 3
056
–
071 Automatic movement 4
072
–
087 Automatic movement 5
088
–
103 Automatic movement 6
104
–
119 Automatic movement 7
120
–
135 Automatic movement 8
136
–
151 Sound-active movement 1
152
–
167 Sound-active movement 2
168
–
183 Sound-active movement 3
184
–
199 Sound-active movement 4
200
–
215 Sound-active movement 5
216
–
231 Sound-active movement 6
232
–
247 Sound-active movement 7
248
–
255 Sound-active movement 8
13 Control Functions
All functions are executed
after 2 seconds.
000
–
049 No function
050
–
059 Blackout during pan/tilt or colo/gobo change
060
–
069 Disable blackout during pan/tilt or colo/gobo change
070
–
079 Blackout during pan/tilt
080
–
089 Disable blackout during pan/tilt
090
–
099 Blackout during color change
100
–
109 Disable blackout during color change
110
–
119 Blackout during gobo change
120
–
129 Disable blackout during gobo change
130
–
139 No function
140
–
149 Reset pan/tilt
150
–
169 Reset color/gobo/focus/prism
170
–
199 No function
200
–
209 Reset all
210
–
255 No function

10
7-Channel Operation
Channel Function Value Description
1 Pan 000–255 Pan angle, 0° (000) to 540° (255)
2 Tilt 000–255 Tilt angle, 0° (000) to 270° (255)
3 Shutter 000–003 Closed
004–007 Open
008–076 Strobe, slow (008) to fast (076)
077–145 Pulse, slow (077) to fast (145)
146–215 Random strobe, slow (146) to fast (215)
216–255 Open
4 Color Wheel 000–006 White
007–013 Red
014–020 Green
021–027 Blue
028–034 Yellow
035–041 Purple
042–048 Light Blue
049–055 Orange
056–063 Pink
064–127 Color indexing
128–189 Clockwise, fast (128) to slow (189)
190–193 Stop
194–255 Counterclockwise , slow (194) to fast (255)
5 Gobo Wheel
See Technical Specifications >
Gobos to view gobo patterns.
000–007 Open/white
008–015 Gobo 1
016–023 Gobo 2
024–031 Gobo 3
032–039 Gobo 4
040–047 Gobo 5
048–055 Gobo 6
056- 063 Gobo 7
064–071 Open spot shaking, slow (064) to fast (071)
072–079 Gobo 1 shaking, slow (072) to fast (079)
080–087 Gobo 2 shaking, slow (080) to fast (087)
088–095 Gobo 3 shaking, slow (088) to fast (095)
096–103 Gobo 4 shaking, slow (096) to fast (103)
104–111 Gobo 5 shaking, slow (104) to fast (111)
112–119 Gobo 6 shaking, slow (112) to fast (119)
120–127 Gobo 7 shaking, slow (120) to fast (127)
128–189 Counterclockwise gobo change, fast (128) to slow (189)
190–193 Stop at current position
194–255 Clockwise gobo change, slow (194) to fast (255)
6 Gobo Rotation 000–127 Indexed position, 0° (000) to 360° (127)
128–189 Counterclockwise gobo scroll, fast (128) to slow (189)
190–193 Stop at current position
194–255 Clockwise gobo scroll, slow (194) to fast (255)
7 Prism 000–127 No function
128–255 Prism effect

11
Technical Specifications
Specifications are subject to change without notice.
Light Type LED
Power 60 W
Colors 8 + white, split colors, scrolling
Gobos 7 + open, slot-and-lock replaceable with rotation,
indexing, gobo shake & scrolling
0.93” (23.5 mm) outside
0.75” (19 mm) image
0.04” (1.1 mm) max thickness
Illuminance 3,700 lux @ 3 m (9.8 ft.)
Beam Angle 18°
Strobe Rate 0
–
20 Hz + pulse and random
Pan Ranges 540°, 360°, 180°
Tilt Ranges 270°, 180°, 90°
Focus Manual
Prism 3-facet with rotation and indexing
DMX Display
Full-color LCD
Connections
1 3-pin input for DMX
1 3-pin output for DMX
Channel Profiles 7, 13
Power Supply
Switching (internal)
Automatic voltage selection
Connection Standard IEC input
Consumption 84 W, 36 V, 2 A at 230 V, 50 Hz
Input Voltage 110
–
240 VAC, 50/60 Hz
Fuse 250 V, 4 A
Physical / Mechanical Mounting 1/4-turn hanging bracket
(
clamp not included)
Dimensions
(width x depth x height)
23.8” x 12.6” x 11.0”
605 x 320 x 279 mm
Weight 12.4 lbs.
5.6 kg

Lumen Output
Lumens: 41700 3700 1390
Distance (m):0 1 3 5
(ft.): 0 3.3 9.8 16.4
Diameter (cm): 0 33 107 180
(in.): 0 13.0 42.1 70.9
Gobos
These are the 7 gobos included with Gesture Spot 300.
marqlighting.com
Manual Version 1.2
18°